en tain t con er. em om e on t to ar we d de an tier eck n. Ch atio ior qu g fre ba tly. en pla Re ce cke cra en wh d or da ma ge ly a me ed nd lac rep rec d. Us jec ub er. tain t con en iss s con G we NINte mo era t op WAR no er tain rly pe is pro les r un Do t to ub er tain s con ar we tier d de an atio ior n. Ch eck ba tly. en qu g fre ce pla Re d or cke cra en wh d.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • Read, understand, and follow all instructions in the manual and on the machine before starting. • Only allow responsible adults, who are familiar with the instructions, to operate the machine.
SAFETY RULES Safe Operation Practices for Ride-On Mowers • • • • • • • • • • • • • • Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. Never carry passengers or children even with the blades off. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Never carry children. They may fall off and be seriously injured or interfere with safe machine operation.
KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference.
ASSEMBLY 1 2 BAGGER SUPPORT ASSEMBLY (See Figs. 1A & 1B) MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting coverassembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. 1. Remove and discard the upper bolt on both sides of the drawbar.
3 4 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side first with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right container should always overlap left container at center supports. 2.
5 6 LOWER CHUTE (See Fig. 5) 1. Raise and hold deflector shield in upright position. 2. Place slot in lower chute over tab on mower deck and position lower chute over deck opening as shown. 3. Hook rear latch into flange hole on back of mower deck. 4. Hook front latch into tab hole on front of mower deck. UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover.
OPERATION • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • Your bagger is equipped with a dump bag indicator. As the bags become full, the flow indicating ball will drop down in its slot, indicating that the bags are full or the chutes have become clogged.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. CAUTION: Do not leave grass in bagger containers. Empty containers after each use and before storing.
REPAIR PARTS/PIÈCES DE RECHANGE GRASS CATCHER - - MODEL NUMBER LTB48A / RAMASSE-HERBE - - NUMÉRO DE MODÈLE LTB48A PRODUCT NUMBER 964 77 62-00 / NUMÉRO DE PRODUIT 964 77 62-00 3 5 20 2 4 6 34 7 8 2 20 37 10 12 9 13 20 20 14 39 38 9 40 18 20 20 40 2 15 16 2 15 20 W RA D INo tonbous p ej GtN are t tc arc 10 e o kc om aew de rew na r ad ro lnu d se ted gam c s rei .de no roi iat ita esU ren C .no ylno si rp kceh er a po oc lre ab siy rf g emm tsn euqe edn lla d de .yltn lper C.
REPAIR PARTS/PIÈCES DE RECHANGE GRASS CATCHER - - MODEL NUMBER LTB48A / RAMASSE-HERBE - - NUMÉRO DE MODÈLE LTB48A PRODUCT NUMBER 964 77 62-00 / NUMÉRO DE PRODUIT 964 77 62-00 KEY NO. PART NO.