PoulanPRO ! Por favor, el aparato al lugar de compra. Please do no not devuelva return unit to retailer. Veuillez ne pas retourner I'outil au detaillant. • 1-800-554-6723 www.poulan-pro.com Instruction Manual Manual de Instrucciones Manuel d'lnstructions BVM200VS & IMPORTANT MANUAL MANUAL IMPORTANTE - Do not throw away - No Io descarte MANUEL - A Conserver IMPORTANT WARNING: Read and follow alt Safety Rules and Operating Instructions before using this product.
zi ____.....A use can cause serious injury. iIWAI-ININB: This unit can be dangerous! t_1 Careless or improper and can follow all warnings and safety rules before operating the unit. to dooperator's so can result in serious operator's understand manual 1 Failure Read your manual carefully injury. until Save you completely The blower can throw objects violently. You can be blinded or injured. Always wear hearing protection and safety glasses marked Z87.
I® When using the vacuum attachment, the unit is designed to pick up dry material such as leaves, grass, small twigs, and bits of paper Do not vacuum stones, gravel, metal, broken glass, etc., to avoid severe damage to the impeller WARNING: Fire hazard. Never mix, pour, or store gasoline or use the unit near a flame or sparks (including smoking, open flames, or work that can cause sparks). WARNING: The muffler is very hot during and after use.
MAINTAIN • Move at _east 10 feet (3 meters) away from fuel and fueling site before starting engine. • Always store gasoline in a container approved for flammable liquids. OPERATE YOUR UNIT SAFELY Ai_WARNING: YOUR UNIT PROPERLY WARNING: Disconnect spark plug before performing maintenance except for carburetor adjustments. • Have all maintenance other than the rec- Stop the engine before opening the vacuum inlet door.
WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or b_ower tubes. The rotating blades can cause serious injury. Always disconnect the spark p_ug before performing maintenance or accessing movable parts. _:_WARNING; If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure.
b_ower tubes. The rotating blades can cause serious injury 1. Insert the tip of a screwddver into the latch area of the vacuum inlet. 6. Align slanted end of lower vacuum tube as shown. Firmly push lower vacuum tube into upper vacuum tube. Slanted Vacuum Inlet Cover 2. Gently tilt the handle of the screwddver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. 3. Hold the vacuum inlet cover open until upper vacuum tube is installed.
KNOW YOUR BLOWER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the Jltustrations with your unit to famitJadze yourself with the location of the various controls and adjustments. Save this manual for future reference. Upper Vacuum Tube Elbow Tube Lower Vacuum Throtbe Trigger STOP Switch _ Starter Rope Tube Spark Plug Upper Blower Tube Lower Blower Tube High-Speed Nozzle Fuel Mix Fill Cap Primer Button STOP SWITCH The STOP switch is used to stop the engine.
• To reduce noise _eveis, operate power blowers at the lowest possible throttle speed to do the job • Use rakes and brooms to loosen debds before blowing. • In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available. • Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens. • Watch out for children, pets, open windows, or freshly washed cars.
4 5 6 7 Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times. As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position. Pull starter rope sharply until engine runs, but no more than 6 pulls. NOTE: If the engine does n't start after 6 pulis (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times.
Cleaning the air filter: 1. Clean the cover and the area around it to keep debds from falling into the carburetor chamber when the cover is removed NOTE: Move choke lever to RUN position before opening air fi_ter cover. CHECK MUFFLER MOUNTING SCREWS Once each year, ensure muffler mounting screws are tightened securely to prevent damage. f- 2. Open air filter cover by pushing button (see illustration) Remove air filter. NOTE: Do not clean filter in gasoline or other flammable solvent.
CARBURETOR ADJUSTMENT Idle Speed Screw The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: • Engine will not idle when the throttle is released. Idle Speed Adjustment Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow). • Turn idle speed screw clockwise to increase engine speed if engine stalls or dies. • Turn idle speed screw counterclockwise to decrease engine speed.
TROUBLESHOOTING _ TABLE WARNING: Always stop unit and disconnect spark plug before performingany of the recommended remedies below other than remedies that require operation of the unit. TROUBLE CAUSE Engine will not start. REMEDY 1. Engine flooded. 2. Fuel tank empty. 3. Spark g_ug not firing. 4. Fuel not reaching carburetor. 5. Compression Engine will not idle properly. low ;i l. carburetor. Engine will not accelerate, lacks power, or 1+ Air filter dirty. 2. Fue{ not reaching carburetor.
In Canada, contact: Poulan PRO Poulan PRO, a division of Husqvarna Outdoor Products Inc., warrants to the odginal consumer purchaser that each new Foulan PRO brand gasoline tao_ or attachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as fo_bws from the odginal date of purchase.
of parts not made or approved by the orkjinaJ equipment manufacturer. You are responsible for presenting your small off-road engine to an Poulan PRO authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call Poulan PRO at 1-800-554-6723.