21 030 OWNER’S MANUAL Model QCT348 Mfg. ID No. 96072000800 Product No. 960 72 00-08 48 Inch Mower Grass Catcher • • • • Printed in U.S.A. Assembly Operation Customer Responsibilities Repair Parts 402345 Rev. 1 12.19.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug.
SAFETY RULES Safe Operation Practices for Ride-On Mowers IV. TOWING • • • • • • Tow only with a machine that has a hitch designed for towing. Do not attach towed equipment except at the hitch point. Follow the manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Never allow children or others in or on towed equipment. On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Travel slowly and allow extra distance to stop.
KNOW YOUR GRASS CATCHER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE ASSEMBLING OR OPERATING YOUR GRASS CATCHER. Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to prevent injury to yourself and others. Save this manual for future reference.
ASSEMBLY 1 BAGGER SUPPORT ASSEMBLY 3. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 4. Be sure support assembly is seated properly and secure with retainer spring supplied. Determine which type drawbar you have on your tractor. Compare the drawbar illustrations below to the drawbar located at the rear of your tractor. Follow the support assembly instructions that apply to your type drawbar.
2 3 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2.
4 6 CONTAINER MOUNTING (See Fig. 4) UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bagger indicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 1.
OPERATION • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • Your bagger is equipped with a full bagger indicator. Movement of the wheel increases as the bags fill. The wheel will be spinning fastest just before the bags fill completely. When the wheel stops, it indicates that the bags are full and the chutes have become clogged.
CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS STORAGE Always observe safety rules when performing any maintenance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. Store in a clean, dry place. CAUTION: Do not leave grass in bagger containers. Empty containers after each use and before storing.
REPAIR PARTS/PIÈCES DE RECHANGE GRASS CATCHER - MODEL QCT348 (MFG. ID 96072000800) / RAMASSE-HERBE - MODÈLE QCT348 (MFG. ID 96072000800) PRODUCT NO. 960 72 00-08 / NUMÈRO DE PRODUIT 960 72 00-08 4 5 6 7 8 10 2 9 12 13 9 11 14 2 18 38 20 15 38 20 34 15 9 20 12 37 10 14 3 20 33 26 AW NR n oD I o to bus j GtN rep tce rc e a ot kca om aew de rew na r ad ro lnu d se ted gam c s rei .de no roi iat ita esU ren C .no ylno si rp kceh er a po oc lre ab siy rf g emm tsn euqe edn lla d de .
REPAIR PARTS/PIÈCES DE RECHANGE GRASS CATCHER - MODEL QCT348 (MFG. ID 96072000800) / RAMASSE-HERBE - MODÈLE QCT348 (MFG. ID 96072000800) PRODUCT NO. 960 72 00-08 / NUMÈRO DE PRODUIT 960 72 00-08 KEY NO. PART NO.