PD-710/ PD-710T In-Dash 7 ” Monitor Touch Screen DVD/CD/MP3/MP4 AM/FM Radio Built-in TV tuner Owner’s Manual Take the time to read through this owner’s manual. Familiarity with installation and operation procedures will help you obtain the best Performance from your new DVD-receiver.
WARNING! To promote safety, certain functions are disabled unless the parking brake is on. The Unit is designed to detect parked status and must be connected to the power supply side of the parking brake switch. Improper connection or use of his connection may violate applicable law and may result in serious injury or damage. To avoid the risk of damage and injury and the potential violation of applicable laws, this unit is not for use with a video screen that is visible to the driver.
CONTENTS WARNING! ................................................................................................................. 2 OPERATION PRECAUTIONS .................................................................................... 2 Accessories ................................................................................................................ 4 INSTALLATION / UN-INSTALLATION........................................................................ 5 WIRING CONNECTIONS ..................
Accessories Package contains the following accessories for installation and operation of the unit. (1) Washer, Spring Washer, M5 Nut 1 each (2) Mounting Strap 1 (3) Bolt 1 (4) Screw4*6 4 (5) Mounting Collar 2 (6) Release Key 2 (7) Screw 5*20 1 Power cable Remote Control Speaker cable Warranty card 1x AV-IN Cable Trim ring 1 Note: Product image may vary from the actual delivery.
INSTALLATION / UN-INSTALLATION Note Before starting installation of the unit, make sure the wiring is connected properly. Use only the parts provided with the unit to ensure proper installation. The use of unauthorized parts may cause malfunction. Install the unit where it does not get in the driver’s way and will not injure the passenger in case there is a sudden stop, like an emergency stop.
WIRING CONNECTIONS NOTE: Never connect cable to the system while it is connected to the battery power. Whenever the unit is disconnected from the battery, the preset memory will be erased and the unit will go back to its factory defaults. Note: To watch video the parking wire should be connected to break signal. 2 cables are connected to a Hands-Free device (not included).
Note: - - Only use groundless loudspeakers. Use only loudspeakers of minimal 40Watt, using fewer watts may result in damaging your loudspeakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit. Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car body (GND). The unit is using a BTL circuit and each loudspeaker must be connected with insulated cables according the diagram.
Front pane Inner panel 1. IR Sensor IR Remote control signal receiving window. Max distance is 6-8 meters, 45 angels. 2 VOL- button Press to decrease volume level.
3 VOL+ button Press to increase volume level. 4. POWER/MUTE Button Press it to turn on the unit, press it again to turn the unit off. Short press it to MUTE the volume output, press it again to resume volume when the power is on. 5. MODE Button Press it to select the mode: Radio, DISC (if there is a disc in unit), USB (if there is a USB device in the unit), CARD (if there is a SD/MMC card in the unit), TV (for PD-710T) and AV IN.
REMOTE CONTROL 1: 2: 3: 4: 5: 6: 7: 8: 9: MODE POWER BAND/RANDOM ENTER UP/DOWN/LEFT/RIGHT EJECT STEREO/MONO P.SCN/RPT BACKWARD/SEEKFAST BACKWARD 10: LOUD 11: OSD 12: PBC/STOP 13: Digit numbers 14: Play/Pause 15: MUTE 16: MENU 17: SUBTITLE 18: SETUP 19: ANGLE 20: INT 21: VOLUME PLUS 22: A-B/ZOOM 23: SEL 24: FORWARD/SEEK+ FAST FORWARD 25: VOLUME MINUS 26: AUDIO/GOTO 27: DUAL (Option without function) 28:OPEN/TILT (Option without function) 1.
9. / seek- buttons In DVD mode, Press button to skip to the previous track. Press and hold button for two seconds to activate fast reverse (REW) search in a track. In RADIO mode, press button to start searching automatic, press and hold for two seconds to start manual searching. button Frequency down. 10. LOUD button Press to set LOUD on or OFF. 11. OSD button In DVD mode press it to enter the OSD menu, press and hold for 2 seconds to set video setup.
26. AUDIO/GOTO button In DVD mode press it to select the audio language. In VCD mode, press it to select the sound track in the sequence of MONO L =>MONO R =>STEREO. Go to: in DVD mode,press and hold for 2 seconds to show TIME SEARCH menu, select number and confirm to go to certain position directly. When press button to enter TITLE/CHAPTER selection mode, select number and confirm to go to certain TITLE or CHAPTER position directly. 27. DUAL button (Option without function) 28.
MAIN MENU The best way to discover the program is to explore each screen in detail, and to find out how to move from one to another. Read this chapter for a guided tour. Unit starts by displaying the Main menu. This is the root of the screen hierarchy, and you can simply access all features by tapping on the touch screen buttons. Tap the corresponding icons to enter a desired mode. ◆ RADIO PLAYER To start Radio, tap RADIO button on main menu screen.
◆ DVD PLAYER To start DVD Player, tap on DVD button from main menu screen. TOUCH SCREEN MENU You will not see any buttons while DVD is played. Buttons will appear when you tap on TFT screen. Tap the screen again to hide the buttons. Insert DVD disc insert VCD disc NOTE DVD Player will automatically start playing when you insert any DVD disc, MEMORY card or USB device. 2. Warning displays if the vehicle is moving for driver's safety. 3.
In DVD mode touch it to enter TITLE MENU (Enable only if the DVD disc with title menu). / Touch it to select previous or next track. ◆File DISC/USB/SD/MMC interface When a file disc, USB or a memory card is played, the screen will show following interface: Mute the sound. Stop button. Press it to Stop playback from the current position, press it again to final stop to the very beginning Play/pause button. Press it to pause the track, press again to resume.
◆AV-IN Mode To start AV-IN Mode, tap on AV-IN button from main menu screen. Connect the external audio/video signal source to this unit. Select AV-IN mode in the main menu or by pressing repeat Mode button on the front panel. Note: If there is no external video input, the TFT displays “NO SIGNAL”. Press the icon to be back to main menu. ◆SETTING CONTROL Your device has default system settings. You can customize the settings to suit your personal needs.
DISPLAY CONTROL Tap DISPLAY button to show DISPLAY menu. SCREEN Screen setting 16:9, 4:3,FULL Backlight Backlight setting LOW, MID, HIGH AREA Set AREA:EUROPE-U.S.A-SOUTH AMERICA-RUSSIA RADIO CONTROL Tap RADIO button to show RADIO menu. STEREO Set STEREO ON or OFF LOCAL Set LOCAL ON or OFF GENERAL CONTROL Tap GENERAL Button to show GENERAL menu.
[1]. Subtitle Lang setting: With this option you can select the preferred language for the subtitles. When the selected language is recorded on the disc then this language will automatically be shown. If not, the first language recorded on the disc is displayed. [2].Audio Lang setting: With this option you can select the preferred language for the audio output. When the selected language is recorded on the disc (not all discs have multiple languages recorded) then this language will automatically be played.
[7] NTSC/ PAL: Select this menu item to set up your preferred video output format. PAL is commonly used in Europe, NTSC is commonly used in the USA and Japan. Auto is commonly used. [8] DEFAULT: Factory reset. Set all values to Factory default values including memory and preset stations. SYSTEM INFORMATION Press SYSTEM button to show the information of the system. You can view detail system information including serial number of the software.
TV SECTION (For PD-710T only) Connect a TV antenna to the TV antenna jack of the unit. Select TV mode; press on the center of the touch screen, and following interface will be display: 1. In TV mode, press the Play/Pause buttons on remote once to enter TV menu setting, or press touch-screen to choose TV MENU icon to enter TV MENU. 2. Press the / on remote or tap the screen to select one of the setup pages: Auto program => Manual program. 3.
Select this menu item is to set TV system: SECAM => NTSC =>PAL ,press NTER button on the remote or tap the screen to select. Audio Select this menu item is to set the TV sound system: When system setting PAL, press ENTER on remote or tap the screen button to select TV sound system: D/K=>M/N=> B/G=> I. When system setting SECAM, TV sound system B/G=>I=>D/K. When system setting NTSC, press button to automatic skip TV channel term.
NOTES ON DISC Only use groundless loudspeakers. Use only loudspeakers of minimal 40Watt, using fewer watts may result in damaging your loud speakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit. Do not use 3-cable loudspeakers and do not connect the loudspeakers minus to the car body. (GND). using a BTL circuit and each loudspeaker must be connected with insulated cables according the diagram.
TROUBLESHOOTING Symptom CD General Power does not turn on. (No sound is produced.) No sound output when operating the unit with amplifiers or power antenna attached. Cause Remedy Fuse is blown In correct wiring Power antennal lead is shorted to ground excessive current is required or remote on the amplifiers or power antenna. Nothing happens The microprocessor when buttons are has malfunctioned pressed. due to noise, etc.
TROUBLESHOOTING SYMPTOM NO POWER DISC CANNOT BE LOADED. CAUSE THE CAR IGNITION IS NOT ON. THE FUSE IS BLOWN. REPLACE THE FUSE. PRESENCE OF DISC INSIDE THE PLAYER REMOVE THE DISC IN THE PLAYER THEN PUT A NEW UPWARD. INSERT THE COMPACT DISC WITH THE LABEL FACING UPWARD. CLEAN THE DISC OR TRY TO PLAY A NEW ONE. INSERTING THE DISC IN UPSIDE DOWN. DISC CANNOT BE READ. SOLUTION IF THE POWER SUPPLY IS PROPERLY CONNECTED TO THE CAR ACCESSORY SWITCH THE IGNITION KEY TO “ACC”.
TECHNICAL SPECIFICATIONS General Power supply: Current consumption: Maximum power output: Compatible formats: Dimensions (W x D x H) / weight: Working temperature range: ESP function: 11~16V DC max. 15 A 52W x 4 channels (max) DVD/SVCD/VCD/HDCD/MP3/MP4/VIDEO/CDDA/Picture CDCD-R/-RW/DVD±R/±RW playback 165*178*50 mm/2 kg -10℃ - +60℃ 10 sec. for Audio CD, 120 sec.