Welcome Please read this manual thoroughly before installing and operating your new PowerBrightTM Power Inverter. This manual contains information you need to obtain the performance required for your application. Keep this manual for future reference. About PowerBrightTM Inverters PowerBrightTM, an innovator in portable inverter design, has developed a new line of super-efficient power inverters with the highest surge capability in the industry.
• • • • • • • • • • • • • • • WARNINGS: INVERTER OUTPUT This is a heavy-duty device that produces voltages similar to commercial AC power. Danger of shock or electrocution - treat inverter output the same as commercial AC power. Do not use the inverter near flammable materials or in any locations that may accumulate flammable fumes or gases. This is an electrical device that can briefly spark when electrical connections are made or broken. Do not allow water or other liquids to contact the inverter.
• • • • • • • • that plug into AC receptacles to supply a low-voltage DC or AC output to the appliance. Some fans with synchronous motors may slightly increase in speed (RPM) when powered by the inverter. This is not harmful to the fan or to the inverter. Route appliance cords and extension cords to prevent accidental pinching, crushing, abrading and tripping people, Use safety approved extension cords rated at15 amps or higher. GFCI devices may not work with modified sine wave (MSW) power.
• Making the connection to the Positive terminal may cause a spark as a result of current flowing to charge capacitors within the inverter. This is a normal occurrence. • Because of the possibility of sparking, however, it is extremely important that both the inverter and the 12 volt battery be positioned far from any possible source of flammable fumes or gases. Failure to heed this warning could result in fire or explosion.
Front Panel PW3500-12 A. LED Display (Input Voltage/Output Wattage) B. Display Reading Selection Switch (Volt /Watt) C. Four standard North American AC outlets D. ON/OFF Switch. Turns the inverter circuits ON and OFF. E. Overload LED Indicator. If continuous power draw of appliance(s) exceeds 3500 watts, this light will turn ORANGE/RED and the inverter will automatically shut down.
Rear Panel PW3500-12 F. High-Speed Cooling Fans. When the temperature inside the inverter exceeds a preset limit, the Cooling Fan automatically turns on to cool the inverter. When the temperature reduces, the fan turns off G. Positive Power Input Terminal H. Negative Power Input Terminal I. Ground Terminal Determining the DC Power Requirements Powering multiple appliances from the high-power PW3500-12 inverter requires a 12 volt battery.
Sizing the Battery To determine the minimum battery bank ampere-hour rating that you will need to operate appliances from the inverter, and any DC appliances powered by the battery bank. Follow these steps: 1. List the maximum wattage that the inverter has to provide (as above). 2. Estimate the number of hours the appliances will be in use between battery recharges. This will differ depending on appliances.
Cable Gauges When connecting the inverter to a battery bank use the thickest stranded insulated copper wire available, in the shortest length practical. If the inverter and the battery are positioned within four feet of each other, a minimum of #2 gauge wire should be used to make the connections. When the distance between inverter and battery bank is four to six feet, a minimum of #0 gauge wire is required.
6. Connect the unfused cable to the Negative (-) terminal of the battery bank. 7. Connect the Negative cable to the Inverter’s Negative (-) terminal. 8. Insulate the end of cable to be connected to the Pos (+) Inverter terminal. 9. Connect the fused cable to the battery bank Pos (+) terminal. 10. Connect the Pos cable end to the Pos (+) inverter terminal. NOTE: Sparking is normal for the first connection. Make sure you have good secure connections – Do not over-tighten. Operation 1.
5. Attach a "Ferrite Data Line Filter" to the television power cord. More than one filter may be required. These filters are available at most electronic supply stores. Note: Some inexpensive audio systems may produce a slight "buzzing" sound when operated with the inverter. The only solution to this problem is to use a sound system with better power supply filtering.
Troubleshooting PROBLEM: No Input Voltage Reason Poor contact with battery terminals. Blown DC battery fuse(s). Solution Shut down inverter and disconnect. Clean terminals thoroughly and reconnect Turn off inverter. Fix problem. Replace fuse(s) with same type and rating PROBLEM: Inverter is Shut Down Reason Solution Battery voltage below 10 Volts Charge or replace battery. Inverter is too hot (thermal shut down mode). Red indicator is lit Unit may be defective. Allow inverter to cool.
Specifications Name Description Input 12V (10-15V) DC Output 110V AC Output waveform Modified Sine Wave (MSW) Continuous power 3500 Watt Surge power 7000 Watt Efficiency Approx. 90 % Power Switch ON/OFF Control No Load Draw <0.5A DC Battery low alarm 10 ± 0.5 V DC Battery low shutdown 10 ± 0.5 V DC AC output sockets 4 North American Standard 15 amps Internal fuses 30 amp (automotive spade type) Dimensions 8.9” (W) x 6.1” (H) x 19.
Warranty All PowerBrightTM products are warranted to the original purchaser of this product. Please keep a copy of your purchase receipt. Warranty Duration: This product is warranted to the original purchaser for a period of one (1) Year from the original purchase date, to be free of defects in material and workmanship. PowerBrightTM disclaims any liability for consequential damages. In no event will PowerBrightTM be responsible for any amount of damages beyond the amount paid for the product at retail.
Bienvenue S’il vous plaît lire soigneusement ce manuel avant d'installer et d'utiliser votre Onduleur PowerBright®. Ce manuel contient des informations dont vous avez besoin pour obtenir les performances nécessaires pour votre application. Conservez ce manuel pour référence ultérieure. A propos des Onduleurs PowerBright® PowerBright, un innovateur en matière d’énergie portable, a mis au point une nouvelle gamme d’onduleur. Nos onduleurs sont extrêmement efficace (jusqu'à 90%).
• Ne pas utiliser avec des appareils mouillés ou des câbles endommagés. • • MISES EN GARDE: l’environnement d'exploitation de l’onduleur • en périphérie de la température de l'air devrait être comprise entre -20 ° C et 40 ° C - idéalement entre 15 ° C et 25 ° C (60 - 80 ° F). • Gardez l'onduleur à l'abri du soleil, si possible. • Gardez la zone entourant l'onduleur clair pour assurer une libre circulation d’air autour de l'unité. Si la température interne devient trop chaude l'unité va s'arrêter.
• Cet onduleur n'est pas d'utilisation dans les applications marines. • Dans le cas d'une alarme sonore continu ou automatique arrêt, éteindre l'onduleur immédiatement. Ne pas redémarrer l'onduleur jusqu'à ce que la source du problème a été identifié et corrigé. • Lors de l’utilisation de chargeurs de batteries a plomb acide, surveiller la température du chargeur de batterie pour environ 10 minutes. Si le chargeur de batterie devient anormalement chaud, débranchez immédiatement l'onduleur.
Mise en route Quand un appareil motoriser où un outil s'allume, il produit une première poussée. Cette poussée de puissance que l'on appelle «la charge de pointe." Une fois démarrée, l'outil ou l'appareil nécessite moins de puissance pour fonctionner. Ce qu’on appelle la «charge continue" en termes de puissance. Vous devrez déterminer la quantité d'alimenter votre outil ou appareil a besoin pour démarrer (à charge) et la continuité du fonctionnement de charge nécessaires (charge continue).
Panneaux Frontale PW3500-12 A. Affichage à LED B. Commutateur de sélection (Volt/Watt) C. Quatre prises Nord-américaines D. ON / OFF Allume et éteint l’onduleur. E. LED indicateur de surcharge. Si la puissance continue de l'appareil (s) dépasse 3500 watts, ce feu passera ORANGE / ROUGE et l'onduleur s'arrêtera automatiquement.
F. Ventilateurs a Haute vitesse de refroidissement. Lorsque la température à l'intérieur de l'onduleur dépasse une limite prédéterminer, le ventilateur de refroidissement s'allume automatiquement pour refroidir l'onduleur. Lorsque la température diminue, le ventilateur s'éteindra. G. Bornes d'entrée de l’alimentation positive H. Bornes d'entrée de l’alimentation négative I.
Utilisation du 2000 watts (ou 100 ampères) pendant 10 heures comme exemple ci-dessus, puis 100 RSAP est nécessaire pour 10 heures. Cela nous donne la base ampère / heure (Ah) de la batterie qui est nécessaire. Dix heures à 100 ampères est égal à 1000 ampèresheures (Ah). Cette réponse n'est qu'un début, car il existe d'autres conditions qui déterminent la durée réelle.
Connexion de l'onduleur cet onduleur a un ensembles de câbles de connexion DC, un positif et un négatif. L'ordre des étapes de la procédure suivante minimise le risque de formation d'étincelles à proximité de la banque de batterie. 1. Préparer tous les câble assurer vous de l’épaisseur requise 2. Installer le fusible titulaire dans tous le câble Positif. 3. Assurez-vous que l'interrupteur ON / OFF situé sur le panneau avant de l'onduleur est en arrêt (O). 4.
Note: • L'alarme sonore peut momentanée faire un bref son, lorsque l'onduleur est éteint, également lorsque l'onduleur est connecté ou déconnecté de la batterie de 12 volt. • Lorsque vous utilisez une rallonge électrique a l'onduleur à un appareil, le cordon prolongateur ne doit pas être supérieure à 50 pieds.
Comment un onduleur a onde sinusoïdale modifier fonctionne. Il y’a deux étapes dans la conversion de 12 volt DC (ou de la batterie) a 110v AC. Stage1: l’onduleur utilise un convertisseur DC a DC qui augmenter la tension d'entrée 12V DC de la batterie à 145 volts DC. Stage2: L'onduleur convertit la haute tension à courant continu en 110v AC, en utilisant des transistors MOSFET dans une configuration en pont complet.
Dépannage Problème: pas de tension d'entrée Raison Mauvais contact avec les terminaux de batterie Fusibles DC brûler Solution éteindre l'onduleur et déconnectez. Nettoyer les terminaux de manière approfondie et reconnecter Éteignez l’onduleur. Remplacer les fusible avec le même type et capacité Problème: L’onduleur s’éteint Raison Le voltage de la batterie est en dessous de 10 Volt Onduleur est trop chaud (mode arrêt thermique).
Spécifications Nom Description Entrée 12V (10-15V) DC Sortie 110V AC Forme d'onde de sortie onde sinusoïdale modifiée Puissance continue 3500 Watt courant de charge 7000 Watt efficacité Approx. 90 % Contrôle Courant pas de charge Alarme de Batterie faible Arrêt Batterie faible AC 4 prises de courant Fusible interne ON/OFF Contrôle Dimensions 8.9” (W) x 6.1” (H) x 19.9” (D) Poids net 25 lbs <0.15 ADC 10 ± 0.5 V DC 10 ± 0.
Garantie Tous les produits PowerBrightTM sont garantis à l'acheteur original de ce produit. S’il vous plaît garder une copie de votre reçu de caisse. Durée de garantie: Ce produit est garanti à l'acheteur original pour une période de un (1) an à compter de la date d'achat d'origine, d'être à l'abri de défauts de matériel et de main-d'œuvre. PowerBrightTM décline toute responsabilité pour dommages et intérêts.