POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM 5” 14HP Chipper Shredder 4” 9.5HP Chipper Shredder MODEL PK0915 (5”) / PK0903 (4”) OWNER’S MANUAL AND OPERATIONS GUIDE WARNING: This product can expose you to chemicals including benzene, carbon monoxide, and lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM General Safety Rules Read this Safety & Operating Instructions manual before using your Power King Chipper Shredder. Become familiar with the operation and service recommendations to ensure the best performance from your machine. If you have any questions or need assistance, don’t hesitate to give us a call at 1-800-344-3371 or send us an E-mail at support@qvtools.com.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Protecting Yourself and Those Around You This is a high-powered machine, with moving parts operating with a high amount of energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you as well as anyone else in the vicinity.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Safety with Gas Powered Engines Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always follow these precautions: • Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon monoxide, which is an odorless, tasteless, and a deadly poisonous gas.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM • The muffler and engine become very hot and can cause severe burns. DO NOT TOUCH! A Note to all Users No list of warnings and cautions can be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate the chipper in a safe manner.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Chipper Operation All branches should not exceed 5in (PK0915)/ 4in (PK0903) diameter. Fresh cut branches and straw are recommended for best performance. Due to different hardness and moisture content, the engine may struggle but will continue to chip. Proper insertion of branches is large diameter to smaller diameter. It is best to put branches with leaves all together. Small logs are not recommended. Procedure 1. 2. 3. 4. 5. 6. 7. 8. 9.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Before performing any maintenance procedure or inspection, stop the motor, unplug the spark plug and wait 5 minutes to allow all parts to cool. Disconnect the spark plug wire to prevent accidental startup. Important Setup Notes Our unit does NOT have a GEAR REDUCTION SYSTEM as noted in the Kohler manual. This engine does not need OIL for a GEAR REDUCTION SYSTEM. Unit does NOT come with oil.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM The blades can be removed by using the included T-bar wrench or a 17mm Socket with extension and ratchet driver. Make sure to use scrap wood or any soft material in the drum to prevent it from moving. If the drum moves, you may strip the bolts. Also, use rags or paper towel in the entry to prevent bolts or blades from falling into the drum. Bar Blade The bar blade is located at the bottom of the drum housing towards the entry chute.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Troubleshooting SYMPTOM The engine won’t start. (Please refer to the engine user manual for engine-specific procedures.) The engine lacks power or is not running smoothly. (Please refer to the engine user manual for engine-specific procedures.) Engine smokes. (Please refer to the engine user manual for engine-specific procedures.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Assembly Number Part 1 Drum Housing 2 Wheel 3 Axle Stand 4 Support Leg 5 Tow Bar Joint 6 Tow Bar 7 Locking Knob 8 Safety Pin Installation Procedure: 1. Lay the Drum Housing (1) on a small platform. Make sure it has space on the sides for installation of the wheels (2) and support leg (4). 2. Attach wheels (2) to axle stand (3) and use the proper nuts to secure. 3. Attach wheels (2) with axle stand (3) to the drum housing (1) using proper bolts 4. 5.
POWERKING Number Part 1-800-344-3371 9 Entry Chute 10 Exit Chute SUPPORT@QVTOOLS.COM 11 Adjustable diverter 12 Set Knob 10. Attach the hinge of the entry chute (9) to the hinge on the drum housing (1). Use latch mechanism to secure. 11. Attach the hinge of the exit chute (10) to the hinge on the drum housing (1). Use latch mechanism to secure. 12. Attach adjustable diverter (11) to top of exit chute (10) and use set knob (12) to secure.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.
POWERKING part No.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM WARRANTY POLICY Thank you for choosing QV TOOLS Products. We're here to ensure that your experience is perfect. In some rare instances, you may need some help with a warranty claim. Please call us at 1-800-344-3371. Product must be registered to activate the warranty. Warranty registration is below. Warranty begins from date of purchase. Engine Warranty Kohler engines are covered with a 3-year commercial and 3-year residential warranty for Command Pro series.