Use and Care Manual

ManualsBrandsPower King ManualsEdgers24 in. 14 HP Gas Walk-Behind Trencher with Kohler Engine

Part III: Operating the Trencher

a. Plug chain adapter(13) to the chain axle(2);

b. Hold the chain(6) around chain adapter(13) and axle(2), then secure two head of the

chain with chain pin(4) and chain lock(3);

c. Secure bolt(55) until the chain is tight enough;

d. Assemble chain cover(14) to the fixation(70) and secure with bolt(67) tightly.

Starting

Be sure the depth control is in the “0” depth position and move both stop switches to the

“ON” position. Always stand to the rear of the trencher, away from the side delivery auger

and digging chain while starting the engine. Always start the trencher at the job site and

allow it to warm up. While the machine is running, check that all controls are working

properly before using.

Start the engine following the procedures:

1. Make sure the fuel shut-off valve is in the “ON” position.

2. Move the choke control lever to the “CHOKE” position (should only be needed if the

engine is cold).

3. Move the throttle control lever to the “FAST” position.

4. Recoil Start: Turn the Ignition Switch to the “On” position. Grasp the recoil starter

handle and slowly pull until you feel resistance. Let the cord retract a little bit then pull

the cord rapidly to start the engine. One or two pulls usually starts the engine.

5. Electric Start: Turn and hold the Key in the start position until Engine starts then let

the Key return to run position.

6. Move the choke control lever (if used for cold engine) slowly back to the “RUN”

position when the engine is running well.

7. If the Trencher has not been running (cold engine), warm up the engine by running the

engine at half throttle for 3 to 4 minutes, then advance the engine throttle control to the

maximum speed.

Summary of content (7 pages)

PAGE 1
Part III: Operating the Trencher a. Plug chain adapter(13) to the chain axle(2); b. Hold the chain(6) around chain adapter(13) and axle(2), then secure two head of the chain with chain pin(4) and chain lock(3); c. Secure bolt(55) until the chain is tight enough; d. Assemble chain cover(14) to the fixation(70) and secure with bolt(67) tightly. Starting Be sure the depth control is in the “0” depth position and move both stop switches to the “ON” position.
PAGE 2
Part III: Operating the Trencher Trenching Be sure the digging chain is not turning when the engine is at an idle. Be sure the engine is off or at an idle before moving the trencher at the job site. Figure 1 WORK POSITION 450mm TRENCHER 600mm TRENCHER Depth “0” 0mm 0mm Depth “1” ,1 ,1 Depth “2” ,1 ,1 Depth “3” ,1 ,1 Depth “4” ,1 NOTE: All depths are approximate. Actual depth may vary depending upon soil conditions and trencher blade wear.
PAGE 3
Part III: Operating the Trencher 4. Using an intermittent pulling action, pull the trencher toward you 4 to 6 inches then relax your pull, allowing the trencher to again reach the chosen depth. 5. Repeat this action until you have finished the job. The wheel lock will aid you in this operation by helping to hold the trencher in position until the next motion is started. Stopping There are two stop switches on the trencher; one on the handle bar and one on the engine.
PAGE 4
Part III: Operating the Trencher Fuel Safety WARNING A. B. C. D. E. F. Refuel outdoors and where no sparks and flames. Store fuel in a container approved for gasoline. Do not smoke or allow smoking near fuel or the trencher or while using the trencher. Clean up all fuel spills before starting engine. Move at least 10 feet away from fueling site before starting engine. Stop engine before removing fuel cap. Digging Safety WARNING A.
PAGE 5
Part IV: Maintaining The Thencher PART IV: Maintaining Your Trencher Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures. Maintenance Safety NOTICE A. Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. B. Disconnect the spark plug wire, keeping it away from the spark plug.
PAGE 6
Part IV: Maintaining The Thencher Lubrication NOTICE All Bearings of Trencher are sealed units and should have sufficient lubricant to last the life of your machine with normal use. Transportation and Storing NOTICE A. Always shut off the fuel valve and engine. B. Always allow the engine to cool. C. Store trencher and fuel where fuel vapors cannot reach sources of combustion like, water heaters, electric motors, switches, furnaces, etc. D.
PAGE 7
Part VI: Troubleshooting and Parts List PART V: Troubleshooting and Parts List Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact the dealers in your area. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it away from the spark plug.