Replacement Part List

10
1. Operation manual ņDFFRPSDQ\LQJ¿OH3OHDVHFDUHIXOO\
read the operation manual before operation and properly
keep the operation manual for future learning and
reference. The operation manual provides safety operation
skills and is necessary for the operator.
2. )ront EaIÀe ņLQVWDOOHGEHWZHHQWKHKDQGOHDQGFKDLQDQG
used to protect the hand of the operator from slipping off
WKHFDUU\LQJKDQGOHDQGEHLQJLQMXUHG7KHIURQWEDIÀHFDQ
also help to control the chain saw. The hand guard can also
help to activate the chain brake to stop the chain.
3. Carrying handle (held by the left hand) ņLQVWDOOHGRQ
the front part of the engine shell and used for supporting.
4. Rear handle (held by the right hand) ņLQVWDOOHGRQWKH
rear part of the engine shell and used for supporting.
5. Hand guard of rear handle ņUHIHUWRWKHH[WHQVLRQSDUW
under the rear handle, which is used to protect the hand
from being injured by the chain broken or moving out of
the slot.
6. Right side plate ņXVHGWRSURWHFWWKHJXLGHSODWHFKDLQ
clutch and sprocket during operation of the chain saw.
7. Tension ing device ņXVHGWRDGMXVWWKHFKDLQWHQVLRQ
8. Locking nut of right side plate ņXVHGWR¿[WKHULJKW
VLGHSODWHDQG¿[DQGGLVDVVHPEOHWKHJXLGHSODWHRIWKH
chain.
9. Guide plate ņXVHGIRUVXSSRUWLQJDQGJXLGLQJWKHVDZ
chain.
10. Chain ņXVHGDVDFXWWLQJWRRO
11. Fuel tank cover ņXVHGWRVHDOWKHIXHOFRQWDLQHU7LJKWHQ
it by means of clockwise rotation.
12. Oil tank cover ņXVHGWRVHDOWKHRLOWDQN7LJKWHQLWE\
means of clockwise rotation.
13. Starter handle ņUHIHUWRWKHKDQGOHRIWKHVWDUWHUXVHGWR
start the engine.
14. Stop switch ņXVHGWRGLVFRQQHFWDQGFRQQHFWWKHLJQLWLRQ
system to start and stop the engine.
15. Starter cover ņUHIHUWRDQLPSRUWDQWFRPSRQHQWIRU
installation of the start-up system and a power-driven
intake channel.
16. Trigger ņDFWLYDWHGE\WKH¿QJHUDQGXVHGWRFRQWUROWKH
engine speed.
17. Trigger control arm ņUHIHUWRDVDIHW\SURWHFWLRQGHYLFH
The trigger cannot be activated until the trigger control
arm is pressed. The trigger control arm can be used to
prevent misoperation of the throttle controller.
18. Choke valve pulling rod ņXVHGWRDGMXVWWKHPL[LQJ
ratio of fuel and air in the carburetor and assist the engine
start-up.
19. $ir ¿lter locking nut ņXVHGWR¿[WKHVPDOOFDSRIWKHDLU
¿OWHU
20. Small cap of air ¿lter ņXVHGWRSURWHFWWKHDLU¿OWHU
21. Large cap ņUHIHUWRWKHJULGVWKURXJKZKLFKFRROLQJDLU
ÀRZV7KHODUJHFDSLVXVHGWRSURWHFWWKHF\OLQGHUVSDUN
SOXJDQGPXIÀHU
22. Guide plate sleeve ņUHIHUWRDSURWHFWLYHGHYLFHXVHG
to cover the guide plate and chain when the chain saw is
relocated or not in use.