L2-402 L2-462 L2-522 L2-652 L2-675 L2-682 L2-692T L2-693 L2-690D L2-700 AUTOSOUND L SERIES SPEAKERS Application Guide Please read through this manual to familiarize yourself with your new speakers. Should your PowerBass Autosound speakers ever require service, you will need to have the original dated receipt.
Thank you and Congratulation Congratulations on your purchase of Powerbass Autosound speakers. You now own a speaker of uncompromising design and engineering from a factory that truly believes in the relentless pursuit of perfection. Incorporating the highest quality parts and state-of-the-art materials, these speakers display the ultimate balance between high fidelity, extreme performance and long-lasting reliability. At Powerbass USA, Inc.
POWERBASS AUTOSOUND L2 FULL RANGE FEATURES Advanced Injection Molded Cone: An injection molded PP cone was developed for better bass performance while minimizing distortion. This ultra lightweight cone is resistant to elements of the environment while giving the listener impeccable listening experience over the factory speakers. Aluminum Hard Dome Tweeter: Ferrofluid enhanced aluminum dome tweeters deliver sharp clarity and crisp treble reproduction.
SPECIFICATIONS FOR POWERBASS L2 SERIES SPEAKERS (Due to Constant Improvements, Specifications and Parameters are subject to change without notice.)* Model * * * *† * Size Nominal Impedance Frequency Response Sensitivity 1W/1M Magnet Size Mounting Depth Power RMS/ Peak L2-402 4” 2-ohm 80-21kHz 87dB 6 oz. 1.75”/44.5mm 40W/80W L2-462 4x6” 2-ohm 70-21kHz 87dB 8 oz. 1.86”/47.4mm 40W/80W L2-522 5.25” 2-ohm 62-21kHz 88dB 10 oz. 1.95”/49.5mm 50W/100W L2-652 6.
Before beginning your installation, thoroughly read this guide and keep it as a reference. It will give you tips on proper placement, wiring, and installation as well as how to obtain the best sound from the PowerBass speakers you have selected. INSTALLATION EXPERIENCE Installation of PowerBass Autosound Speakers requires experience with a variety of mechanical and electrical procedures. This manual only provides general installation and operation instructions.
PREPARING FOR INSTALLATION NOTE: The tools listed below may be required for proper installation. • An electric drill with drill bits • Phillips-head and standard screwdrivers • Wire strippers • Crimping tool and needle-nose pliers INSTALLATION PRECAUTIONS NOTE: Proceed only if you are a qualified installer otherwise; let your dealer do it. • Always wear protective eyewear when using tools. • Turn off all stereo and other electrical devices before you begin.
L2-690D WIRING DIAGRAM The L2-690D has been designed to work with multiple impedance requirements. The dual voice coil dsign can be wired into two different configurations depending on the impedance requirement of your OEM amplifier. * Both coils must be wired in one of the above configurations to ensure proper operation of this speaker.
POWERBASS AUTOSOUND LIMITED WARRANTY POLICY PowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms: PowerBass Autosound Speakers are to be free of defects in material and workmanship for a period of one (1) year. This warranty applies only to PowerBass products sold to consumers by Authorized PowerBass Dealers in the United States of America.
PowerBass Autosound – A division of PowerBass USA, Inc. 2133 S. Green Privado – Ontario, CA 91761 Tel. (909) 923-3868 – Fax (909) 923-8048 www.powerbassusa.
E91B0623 8 3/4” (222.0mm) Cut Out Diametre 4 3/ 4”(120.0mm) Center of Hole to Hole 6” (152.0mm) Cut Out Diameter 6 5/ 8” (169.0mm) Center of Hole to Hole S-693 ww w. p o we Mounting Depth Profundeur D’encastrement Profundida De Montaje S-693 3 3/8” 85.7mm L-6903x 3 3/8” 85.7mm L-6903x rbass m o c usa.
