A u 0 o u n L2-6C AUTOSOUND L2 SERIES COMPONENT Application Guide Please read through this manual to familiarize yourself with your new speakers. Should your PowerBass Autosound speaker components ever require service, you will need to have the original dated receipt.
_.._._,.ower~ A u 0 o u n Thank you and Congratulation Congratulations on your purchase of Powerbass Autosound speakers. You now own a speaker of uncompromising design and engineering from a factory that truly believes in the relentless pursuit of perfection. Incorporating the highest quality parts and state-of -the-art materials, these speakers display the ultimate balance between high fidelity, performance and long-lasting reliability. ••• ••• At PowerBass USA, Inc.
POWERBASS AUTOSOUND L2 COMPONENT FEATURES Advanced Injection Molded Cone: An injection molded PP cone with carbon fiber was developed for better bass performance while minimizing distortion. This ultra lightweight cone is resistant to elements of the environment while giving the listener impeccable listening experience over the factory speakers.
SPECIFICATION S FOR POWERBASS L2 COMPONENTS (Due to Constant Improvements, Specifications and Parameters are subject to change without notice.) Model Size Nominal Impedance Frequency Response Sensitivity 1W/1M Magnet Size Mounting Depth Power RMS/ Peak L2-6C 6.5" 2-ohm 58Hz-21kHz 90dB 8.6oz. 2.13" (54mm) 75W/225W Before beginning your installation, thoroughly read this guide and keep it as a reference.
TIPS TO GET THE MOST OUT OF YOUR POWERBASS SYSTEM Your PowerBass Autosound speakers have been meticulous engineered and designed to handle high power musical reproduction. Despite their rugged construction, it is possible to damage your speaker if they are improperly used. In general, you will hear distortion as a so-called warning before any damage occurs. If you hear distortion in your system, immediately reduce the musical level to the point where the sound retains its clarity. 1.
INSTALLATION PRECAUTIONS NOTE: Proceed only if you are a qualified installer otherwise; let your dealer do it. • Always wear protective eyewear when using tools. • Turn off all stereo and other electrical devices before you begin. • Disconnect the (-) negative lead from your vehicle's battery. • Keep the speakers in the package until final installation. • Locate all fuel lines, brake lines, oil lines, and electrical cables when planning your installation.
COMPONENT SYSTEM INSTALLATION Component Midrange The proper installation procedure for mounting these high performance mid-range speakers is to secure the speaker to the vehicle's speaker mounting hole. Once the speaker is in place, determine if the supplied grill needs to be installed. If so, place the grill in place over the speaker and screw the speaker into the mounting hole. Component Tweeter These high quality tweeters come complete with several mounting housings for installation versatility.
INSTALLATION PROCEDURES By mounting the tweeter separately from the woofer (or mid-range driver) the installer can choose the best location for sound quality and imaging. Three mounting types are possible allowing more versatility for the tweeter location. These are flush mount, surface mount, and angle mount. Flush Mounting (Type A) The best location for the tweeter is usually high up on the door and as far forward as possible without interference from the dashboard.
AUTOSOUND COMPONENT TWEETERS These high quality tweeters come complete with several mounting housings for installation versatility. Typically tweeters should be mounted on axis and as close to ear level as possible. After you have chosen the housing to be used, gently press the tweeter in the proper mounting base. Once the tweeter base is mounted, push and "twist" the housing until it locks to the base. Below are exploded views showing the possible types of tweeter mounting.
CROSSOVER NETWORK INSTALLATION AND WIRING Your PowerBass Autosound Component system contains two separate 2-way crossover networks. When choosing a location to mount the crossovers, keep in mind they contain electronic parts which can be damaged by moisture and dirt. Correct wiring of the crossover is critical to avoid damage to the speakers and ensure true high fidelity sound.
POWERBASS AUTOSOUND LIMITED WARRANTY POLICY PowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms: PowerBass Autosound Speakers are to be free of defects in material and workmanship for a period of one (1) year. This warranty applies only to PowerBass products sold to consumers by Authorized PowerBass Dealers in the United States of America.
••• • • ® PowerBass Autosound -A division of PowerBass USA, Inc. 2133 S. Green Privado - Ontario, CA 91761 Tel. (909) 923-3868- Fax (909) 923-8048 www.powerbassusa.
/ ' / / / powerbAss::r / I I I '' "'\ cv6 11/16" (170.0mm) Edge to Edge Out Side of Basket \ cv5 11/16"(144.0mm) Cut Out Diameter \ TEMPLATE • CALIBRE • PLANTILLA \ I I I I \ \ cv6 1/8"(155.0mm) Center of Screw Holes \ \ I \ \ \ \\,~ I S-65T S-652 S-6C L2-652 L2-6C " "~/J ',0 b p ::: I 0~1 s '0- .v,/ Werbassu, / 2 5/16" (59.3mm) Center of Hole to Hoi I I Mounting Depth Profundeur D'encastrement Profundida De Montaje S-65T 2" 50.8mm S-652 2 3/8" 60.
