ower. . . . X XL-42SS XL-52SS XL-62SS XL-692SS XL-82SS POWERSPORTS SPEAKERS Application Guide Please read through this manual to familiarize yourself with your new speakers. Should your PowerBass Xtreme marine speaker ever require service, you will need to have the original dated receipt.
X Thank you and Congratulations Congratulations on your decision to purchase PowerBass Xtreme™ speakers. You now own a speaker of uncompromising design and engineering philosophy from a factory that truly believes in the relentless pursuit of perfection. Incorporating the highest quality materials and state-of-the-art machinery, these speakers display the ultimate balance between high fidelity, extreme performance and long-lasting reliability. At PowerBass USA, Inc.
XL POWERSPORTS SPEAKERS FEATURES Sealed Cone Design: Aunique interior trampoline gasket seals the pole piece to protect the voice coil from water and moisture. The interior surround and outer surround are constructed of synthetic rubber for long life and UV resistance. This in conjunction with the Polypropylene cone material offers increased performance even in exposed mounting locations.
SPECIFICATIONS FOR POWERBASS XTREME POWERSPORT SPEAKER (Due to Constant Improvements, Specifications and Parameters are subject to change without notice.) Model Size Nominal Impedance Frequency Response Sensitivity 1W/1M Power RMS/ Peak XL-42SS 4" 3-ohm 1OOHz-20kHz 87d8 40W/80W XL-52SS 5.25" 3-ohm 70Hz-20kHz 87d8 50W/100W XL-62SS 6.
INSTALLATION EXPERIENCE Installation of off road and marine audio speakers can require extensive experience with a variety of mechanical and electrical procedures. Although this application guide explains how to install PowerBass Xtreme speakers in a general sense, it may not show the exact installation method for your particular situation. If you feel unsure about personally installing the speaker system, don't attempt the installation yourself.
PREPARING FOR INSTALLATION NOTE: The tools listed below may be required for proper installation • • • • • • • • • • An electric drill with drill bits Phillips-head and standard screwdrivers Wire strippers Crimping tool and needle-nose pliers Silicone sealant or closed cell weather-stripping Metal file (half round) Dust mask (when cutting into fiberglass) Hole saw or jig saw Punch or countersink tool Eye protection NOTE: The stainless steel hardware supplied with your PowerBass Xtreme speakers has been cho
SPEAKER LOCATION The sound produced by your PowerBass XL coaxial speakers is directional. Find the best location for stereophonic sound. Adding more PowerBass Xtreme speakers to the system will not only help to balance the sound, but it will increase the power handling of the system enabling it to play louder. After determining the best mounting locations, carefully check the areas where the mounting hardware will be placed (see Fig 2).
MOUNTING The following drawing shows the typical flush mount installation into a fiberglass panel using the supplied hardware. e=>------ --- ~--------- e=>-----Mesh Grill Speaker Foam Gasket Panel (Flat mounting surface) NOTE: Be sure to use the supplied black putty to secure the mesh grill to the mounting ring. Always follow proper safety procedures. Use eye-protection at all times and a dust mask and gloves when cutting. Check both sides of the vessel before cutting any holes.
Fig. 3 Use template sheet inside Fig. 4 Cut hole Fig. 5 Drill pilot hole (see chart) carton to trace onto mounting location hole to radio + Connect or amplifier -=:)~=~;::::::::::::!!!::::= ......__ _ _ _ _ - Fig.
WIRING PROCEDURES Once the mounting holes have been cut, run the speaker wire from the speaker mounting locations back to the radio. If you are running wires through bulkheads, drill holes for the cable and use a marine grade grommet to properly insulate any rough edges from the wire insulation. Make sure the wires will clear any mechanical devices in the boat and secure them with wire ties. Carefully place the supplied speaker wire in a location that is free of standing water and moving components.
POWERBASS XTREME LIMITED WARRANTY POLICY PowerBass USA, Inc. offers limited warranty on PowerBass products under normal use on the following terms: PowerBass Xtreme Speakers are to be free of defects ·in material and workmanship for a period of one (1) year. The warranty is extended to three .(3) years for parts and labor, if an Authorized PowerBass Xtreme Dealer completes the installation.
PowerBass Xtreme - A division of PowerBass USA, Inc. 2133 S. Green Privado, Ontario, CA 91761 Tel. (909) 923-3868 - Fax (909) 923-8048 www.powerbassusa.
3 13/16" (97.5mm) Center of Hole to Hole /--- --~ ..... , ~ // 6 5/16" (160.0mm) Edge to Edge Out Side of Basket 5 7/16" (138.0mm) First Round Screw Hole /1 powerbAss::r \\ I TEMPLATE • CALIBRE • PLANTILLA \ 4 1/2" (114.
