UPS Uninterruptible Power System UPS-200/250/400 USER MANUAL 66P-S025-036
TABEL OF CONTENTS 1.IMPORTANT SAFETY INSTRUCTIONS … … … … … … … … … … … … . . 1 2.INTRODUCTION … … … … … … … … … … . . … … … … … … … … … … … … … . 5 2.1 SYSTEM DESCRIPTION … … … … … … … … … … … … … . … … … . … … … 5 2.2 FEATURES … … … … … … … … … … … … … … … … … … .. … … … … … … … 5 2.3 OUTLOODING … … … … … … … … … … ... … … … … … … … … … … … … … 6 3.INSTALLATION AND OPERATION … … … … … … … … … … … … … … … . . 7 3.1 SITE SELECTION … … … … … … … … … … … … … … … … … … … … … … . 7 3.
1. IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE INSTRUCTIONS 1.1 • This manual contains important instructions for Model UPS series that should be followed during installation and maintenance of the UPS. • Unplug the unit from the AC outlet and make certain of all switches are in the “off” position before cleaning. Do not use liquid or aerosol cleaners, use only a water dampened cloth for cleaning. • Do not attempt to service this product by yourself.
1.2 SAFETY CAUTION: l l l l This unit is should be installed from service personnel. The equipment can be operated by any individuals with no previous experience. The socket-outlet shall be installed near the equipment and easily accessible. Attention, hazardous through electric shock. Also with disconnection of this unit from the main, hazardous voltage still may be accessible through supply from battery.
2.1 SYSTEM DESCRIPTION: This unit is a stand by uninterruptable power supply (UPS.), it can keep computers or other critical equipments performing through power disturbances and outages. 2.2 FEATURES: • Utilizes microprocessor based controls, minimizes the dependency on hardware, maximizes system flexibility and assures super reliability. • Extremely compact in size, suitable for any available space. • Unit can be TURNED ON any time with or without utility power.
1 UPS-200/250/400 Front Side View 1 BRAND NAME UPS-200/250/400 Rear Side View 2 POWER SWITCH 3 OUTLET SOCKET 4 INLET SOCKET 3 INSTALLATION AND OPERATION 3.
This unit can be installed besides the computer or equipment, do not install it in non-ventilated areas. 3.2 Unpacking The following items are included in the carton l User’s manual. l Power cord. l UPS 3.3 Connecting the UPS For UPS series: Use the power cord to connect the wall power (utility power) and inlet socket. Connecting the power cord of your computer to the UPS output receptacle. 3.4 Staring operation 3.4.
flash and buzzer will be slowly beeping. 3.4.2 Turn on the computer, if it is over loaded, the LED and buzzer will rapidly flash and beep, you should check the power rating of the loaded equipment then remove the less critical one. Generally, the total power consumption of one set of personal computer (color monitor) will not exceed the rating of this UPS. 3.4.3 Unplug the input power cord to test the UPS backup function. The LED and buzzer will be slowly flash and beeping.
A few helpful hints: -Periodically vacuum dust from ventilation openings. -Occasionally wipe exterior with a damp cloth. 5 TROUBLESHOOTING If the UPS fails to operate properly, please check the following TROUBLESHOOGING CHART. If the unit is to be returned for service, please note the following information and pack it in the original carton . a. model number, serial number. b. Date of purchase. c. Full description of problem.
1) Unplug unit from AC power source and disconnect all connected equipment. 2) Disconnect AC power cord from unit. 3) Turn unit upside down and using a phillips screws driver, unscrew the 4 screws holding the top of the unit to bottom. Put screws in a safe place for reconnection. 4) Holding the top together firmly with the bottom, turn the entire unit right side up. 5) Carefully lift top cover off and place to the side. The connecting wires and electronics will be exposed.
charged. Before storing, charger the UPS for at least 4 hours. Remove any accessories in the accessory slot and disconnect any cables connected to the computer interface port to avoid unnecessary draining the battery. 7.2 Extended storage During extended storage in environments where the ambient temperature is –15 to +30℃(+5 to +86℉),charge the UPS’s battery every 6 months. During extended storage in environments where the ambient temperature is +30 to +48℃(+86 to +118.
Frequency (on battery) Transfer Time Spike Protection Overload Protection 50 or 60 Hz +/-2% 2/4 milliseconds, including detection time 320 joules, 2ms UPS automatic shutdown if overload exceeds 110% of nominal at 60 seconds and 130% at 3 seconds.