Quick Tips • Both positive and negative cables must be connected to a battery • Negative cables should not be connected to the chassis • The use of longer cables will require you to increase the gauge of the cables • Please be sure to consult owner's manual for proper cable sizing
1. General Information The POWERDRIVE Inverter App can be installed and used on smartphones with Andriod or IOS. Supports Andriod 4.2 or above. Supports IOS 7.0 or above. fl:t•t❖l< 1 J 1 l 11','fll[IJ.l• IUl!JlJ~ Android phone: Go into Google Play and search "POWERDRIVE". iPhone: Go into the App Store and search "POWERDRIVE". 3. How to set up the connection between your smartphone and inverter Connected POWERD A\VE t oO SETTINGS OONte:T n, ~ TESTING STATUS @ ON/OffSWITH Photo 1 Photo 2 11
A11T• __ , 4:21 PM Not connected A11T• c:nPM 100\- Not connected DEVICES DEVICES ...... Searching Photo 3 · ~ 1500W mr• POWERDRIVE-AEC3 NotPaued POWERDRIVE-BECD Not Pairtd POWERDRIVE·CDFE Not Paired Photo 4 4:2111M [I] ~ [~ [~I ~ I.SETffl.
(1) Please ensure the Bluetooth® on your phone is ON. (2) Click the icon on the screen to activate the APP (Photo 1). (3) Click the "CONNECT" icon (Photo 2). (4) Your phone will automatically search for the inverter (Photo 3). Click the device name to set up the connection (Photo 4). (5) Your phone will ask you to key in a code to set up the connection. The default code is "8888". (6) Once the connection has been made, all 4 working modes are available to use (Photo 5) . 4. Operation tip on t ,, ..
(1) On occasions the Andriod phone will be unable to detect the inverter in the App. If this happens, go to the Bluetooth page on your phone's 11 Settings11 to pair with the inverter. (2) If your Andriod phone has Bluetooth 4.0 or above, you will see two devices in the Bluetooth page, one with an "L" in its name and one without. Always select the one without the 11L11 in its name in your Andriod phone (Photo 6).
(1) Open the App. (2) Click the 11 CONNECT11 icon (Photo 8). (3) Click the name of your inverter, your smartphone and inverter are now disconnected. 6. How to reset the passcode of the inverter To avoid other people connecting with your inverter by mistake. t:21 N ATIT• 1500W C:21 PM 100\~ 1500W ( SETTINGS X INVERTER ALARM [::] * C:OSIECT ~ (1\ STATUS TEJTIN8 PHONE ALARM OU ) LOW/OVER VOLTAGE PROTECTION Off ) LOW NOISE MODE Fmt w,-:1 n,n at low 1,-d with low noiM mode Hltc1ed.
a,ar• 4:11PM t _. . . 1500W < RESET THE PASSCOOE X Please key 111 the ex,sung puscode. II (lxxxx Please key in lhl! lll!W pass~' Ijxxxx u Please key In the new passcode again, Ilxxxx 11 El-. II iI Photo 12 (1) Click the "SETTINGS" icon {Photo 10). (2) Click the "Reset the passcode" and proceed to follow the instructions in Photos 11 & 12.
q il1 ii l{I] {! t•il )161ii ltii •6t{-fij,j, ti?i 1 11 , Photo 13 (S01) Photo 14 (S02) Photo 15 (Battery voltage) (1) Ensure your inverter is connected with a battery successfully. (2) Turn off the inverter. (3) Press and hold the ON/OFF switch for 5 seconds. You will see the digital display flash "S01 11 twice (Photo 13), then flash 11 S0211 three times (Photo 14). Finally, it will show the voltage of the battery (Photo 15).
The inverter can be used in a distance from the battery. POWERDRIVE LEN8l'H Ht 2ft 3ft 4ft 5ft 6ft 7ft 8ft 9ft 10ft AMPERAGE PD1000 PDIP81000I PD1IOO 8AWG 8AWG 8AWG 8AWG 8AWG 6AWG 8AWG 8AWG 6AWG 6AWG 6AWG 4AWG 4AWG 4AWG 4AWG 2AWG 2AWG 2AWG 2AWG 2AWG 2AWG 2AWG 2 AWG 2 AWG 2AWG 2AWG 2AWG 2 AWG 2AWG 2AWG RECOMMENDED FUSE SIZE 150A I 100A I 100A PDIOOO PDIOOO 6AWG 4AWG 4AWG 2AWG 2AWG 1/0AWG 2/0AWG 3/0AWG 3/0AWG 3/0AWG 4AWG 4AWG 2AWG 2AWG 2AWG 1/0AWG 2/0AWG 3/0AWG 3/0AWG 3/0AWG 200A 300A 9.
c::> = = w = = Qn, c:::J C/.) = ....... '1:1 c:,GJ "'~ = = ....... '1:1 ~ 0n, ::::0 c.n = .... :E = = = ....... '1:1 = ....
Please read this manual thoroughly before installing and operating your Inverter. This manual contains information you need to obtain the performance required for your application. Keep this manual for future reference. The PowerDrive®Bluetooth®inverter is the first of its kind in the market! This inverter has high starting capability and max efficiency up to 90%. This Bluetooth® inverter can connect with all Andriod®and iOS® smartphones.
• Do not connect to transfer switch. • Do not connect to household outlets. CAUTIONS: INVERTER OPERATING ENVIROMENT • Surrounding air temperature should be between -4°F-104°F - ideally between 32°F-104°F. • Keep the inverter away from direct sunlight, if at all possible. Keep the area surrounding the inverter clear to ensure free air circulation around the unit. Do not place items on or over the inverter during operation. The unit will shut down if the internal temperature gets too hot.
• This inverter is not tested for use in marine applications. • In the event of a continuous audible alarm or automatic ' shut down, turn the inverter OFF immediately. Do not restart the inverter until the source of the problem has been identified and corrected. • When using your PowerDrive inverter to power lead acid battery chargers (Like those used for a car,boat or motorcycle) with modified sine wave, check the temperature of the battery charger after 1O minutes.
• Because of the possibility of sparking, it is extremely important that both the inverter and the 12-volt battery be positioned far from any possible source of flammable fumes or gases. Failure to heed this warning could result in fire or explosion. • Operating the inverter without correctly grounding the unit may result in an electrical shock. GETTING STARTED When some tools turn on, there is an initial surge of power to start. This surge of power is referred to as the "starting load" or "peak load.
@) .
FEATURES 1. Positive Power Input Terminal. 2. Negative Power ln1put Terminal. 3. High-Speed Cooling Fans. When the temperature inside the inverter exceeds a preset limit, the cooling fan automatically turns on to cool the inverter. When the temperature reduces, the fan turns off. 4. Ground Terminal. 5. Green LED: Battery voltage indicator. 6. Yellow LED: Output power indicator (KW), which will be activated when actual output power larger than 1000W. 7.
Sizing the Battery To determine the minimum battery bank Ampere-hour rating that you will need to operate appliances from the inverter, and any DC appliances powered by the battery bank. Follow these steps: 1. List the maximum wattage that the inverter has to provide (as above). 2. Estimate the number of hours the appliances will be in use between battery recharges. This will vary depending on appliances.
If there is any doubt about sizing the battery bank, it is safe to over estimate the Amp hour requirements of the battery bank. Note: The type of batteries you use to power your high-power inverter is important. Operating a high-power inverter will routjnely discharge batteries and they will require frequent recharging. Batteries used to start engines are not designed to repeatedly charge and discharge. We recommend using "deep-cycle" or "marine" rated batteries.
3. Position the inverter against the mounting surface and mark locations of the mounting screw openings. 4. Remove the inverter and drill four (4) mounting holes. 5. Fasten the inverter to the mounting surface using corrosion-resistant fasteners sized #10 or larger. Connecting the Inverter This inverter has two DC cable connections, one positive and one negative. The order of steps in the following procedure minimizes the danger of sparking near the battery bank. 1.
Note: Sparking is normal for the first connection. 1. Make sure you have good secure connections Do not over-tighten. 2. If you need the information on the panel at a distance, you can take out the panel and connect it to a 12 ' extension cord (included) or simply use the APP. Removable Faceplate Remote Control 1. Remove the screws fixing the panel (Keep the screws safe) 2. Follow the diagram below to connect the panel and extension cord. ~ Operation 1.
Notes: • When using an extension cord from the inverter to an appliance the extension cord should not be longer than 50 feet. TELEVISION AND AUDIO SUGGESTIONS Although all PowerDrive in'lerters are shielded and filtered to minimize signal interference with your television picture may be unavoidable, especially in weak signal areas. Here are some suggestions that may improve reception: 1. First, make sure that the television antenna produces a clear signal under normal operating conditions.
TROUBLESHOOTING PROBLEM: No Input Voltage Solution Cause Battery is defective Replace battery. Blown fuse Ask for help from technician. Lose cable connections Check the connection to the battery. Tighten as required. PROBLEM: Inverter Shut Down Cause The actual output power is higher than rated power of inverter, Overload protection has occurred The actual output is less than rated power, but high starting surge has caused overload .
PROBLEM: Low Battery Alarm on all the time Cause Input voltage below 11 v - buzzing sound Poor or weak battery condition Inadequate power being delivered to_ the inverter or excessive voltage drop Solution Keep input voltage aboye 11v to maintain regulation. Recharge or replace battery. Use lower gauge (heavier) cable. Keep cable length as short as possible. PR~BLEM: TV does not work Cause TV does not turn on Solution Contact TV manufacturer to find out if t~e TV is compatible with a modified sine wave.
SPECIFICATIONS Model PD1000 PD1500 Input PD2000 PD3000 11-15V DC Output 115VAC Output Frequency 58-62Hz Output Waveform 59-61Hz Modified Sine Wave (MSW) ~ontinuous ower 1000W 1500W 2000W 3000W ~u~e o er 2000W 3000W 4000W 6000W 88% Max Efficiency No Load Draw Low Battery Shutdown <1.0A <0.6A 10.5±0.3V DC USB Output Port 2.4A USB-C Output Port 3.
FCC STATEMENT This equipment has been tested andfound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the Instructions, may cause harmful interference to radio communications.
DAS COMPANIES, INC. POWERDRIVE™ ONE YEAR LIMITED WARRANTY This Limited Warranty covers this PowerDrive™ product. This product is warranted against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase ("Warranty Period"). This warranty extends only to the original purchaser and will end when the product is transferred to a subsequent owner.
benefits conferred by DAS’s One Year Limited Warranty are in addition to all rights and remedies conveyed by such consumer protection laws and regulations. How to obtain Warranty Service? Within the first thirty (30) days after the original purchase, products must be returned to the dealer. After thirty (30) days and for up to one (1) year the product may be returned to PowerDrive. When returning products to PowerDrive: Shipping to PowerDrive must be paid by you.
Questions? Please reference the enclosed owner's manual. OR Call 1-866-622-7979 A representative is available Monday - Friday (8 :0 0AM - 4:30PM EST) Send us an email : techsupport@roadprobrands.com Visit our video library: http://www.powerdnveinverters.