POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM 2.8” Direct Drive Chipper Shredder with Kohler RH265 Engine Due to continuing improvements, actual product may differ slightly from the product described herein.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Contents General Safety Rules ......................................................................................................................................... - 2 Getting Familiar with your Wood Chipper ........................................................................................................ - 7 Operating the Wood Chipper ....................................................................................................................
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Additional Information and Potential Changes We reserve the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. General Safety Rules Safety Labels Found on Your Unit Read entire instruction manual before operating. DANGER, pay close attention. Keep hands away from moving parts. Warning: Sharp Blades.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM CAUTION This machine is designed solely to chip wood and must not be used for any other purpose. It should only be used by trained operators who are familiar with the content of this manual. It is potentially hazardous to fit or use any parts other than authorized dealer parts. We disclaim all liability for the consequences of such use, which in addition voids the machine warranty.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Protecting Yourself and Those Around You WARNING Unsafe operation can create several hazards for you, as well as anyone else in the vicinity. Always take the following precautions when using this machine: A．Keep in mind that the operator is responsible for accidents or hazards occurring to other people, their property, and themselves.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM gas. B．Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and open flame, and out of the reach of children. C．Replace rubber fuel lines and grommets when worn or damaged. D．Fill the gasoline tank outdoors, after the engine off and completely cooled. Don't handle gasoline if you or anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM E．Never use the machine without ensuring that all guards and shields are in place. F．Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the Wood Chipper. This includes all shields and guards. Modifications to your machine could cause personal injuries and property damage and will invalid your warranty.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Getting Familiar with your Wood Chipper It may be helpful to familiarize yourself with the controls and features of the Wood Chipper. If you have any question, please contact the QVTools Power King support at 1-800-344-3371 or Support@QVTools.com. Technical Specs Model: PK0913DD Max. Chipping Capacity: 2.8inch Function: Chipping leaves, branches, crop straw and farming feed, etc. Max. Blade Speed: 3600r/min Engine: 6.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Operating the Wood Chipper WARNING A．Read and understand all instructions, safety precautions, and/or warnings listed in “General Safety Rules” before operating the WOOD CHIPPER. If any doubt or question arises about the correct or safe method of performing anything found in this manual, please contact the dealers in your area. B．When operating the Wood Chipper, make sure you are standing in the on the side of the entry chute.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM engine at idle for 3 to 4 minutes, then advance the engine throttle control to the maximum speed. 8. Always keep unit at full throttle when chipping. Stopping Turn the Multi-Use lever to the OFF position. WARNING Do not put your hands into the chute when loading. This is a very UNSAFE method and could result in injury to your hands.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Maintenance Regular maintenance is the way to ensure the best performance and long life of your machine. Check all the parts regularly with 1-2 times monthly including bearing, blades, etc. Replace the blades as soon as the chipping performance begins to deteriorate. The blunt blades will lower working efficiency and cause the damage of machine. Please refer to this manual and the engine manufacturer's user manual for maintenance procedures.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Lubrication NOTICE All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use. Tire Pressure Recommended tire pressure is 10PSI. Blade Replacement Put a log or wood branch to keep drum from rotating. Put a rag under the blade to prevent any bolts from dropping into the drum. Using a 13mm socket wrench break the bolts loose.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Assembly Step 1: Install wheels with Axle, affix with Pin. Step 2: Install the Axle on the frame by bolts, washers and nuts.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Step 3: Fix engine on the frame by bolts, washers and nuts.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM Troubleshooting The common faults 1 The engine cannot be started Elimination method Read the engine users’ manual, check the fuel ON-OFF valve and check proper oil level. Check if the engine is stopped by overloading, check 2 Engine flameout midway if something blocked in the chipping hopper, check the emergency stop button and protection switch.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.
POWERKING 1-800-344-3371 No. SUPPORT@QVTOOLS.
POWERKING 1-800-344-3371 SUPPORT@QVTOOLS.COM WARRANTY POLICY Thank you for choosing QV TOOLS products. We're here to ensure that your experience is perfect. In some rare instances, you may need some help with a warranty claim. Please call us at 1-800-344-3371 or E-mail support@qvtools.com. Product must be registered to activate the warranty. Warranty registration is below. Warranty begins from date of purchase.
