Use and Care Manual
24
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
3. Hex Screw,5/16-24×19 S=12.5
42 Washer,Bell,ij30×ij16×1.6
4. Washer,Bell,ij24×ij8×2
43 Spacer
5. Wheel,Assembly Complete
44 Support Bracket Ass'y,Friction Wheel
6. Spacer
45 Spring, Shift, Lever
7. Friction Disc,Wheel
46. U-Washer,Saddle
8. Hex Screw,ij31×ij20×1.6
47 Nut,Hex Look,5/16-18 S=12.5
9. Friction Disc,Wheel
48 Nut,Hex Look,1/4-20 S=10
10. Ring E-Type,GB/T896-1986 15
49 Regulating-Position Flat
11 Bearing 6203 RSNRC 3
50
Screw,Self-Tapping,ST1/4-20×16-
ij9.40×2.8-
ij13.7×2 S=9.5
12
Screw,Self-Tapping,ST1/4-20×16-
ij9.40×2.8-ij
13.7×2 S=9.5
51. Screw,Self-Tapping,ST1/4-20×16 S=9.5
13 Screw,self-tapping,1/4-20×26 S=9.5 52 Nut,Hex Look,M8X25
14 Screw,self-tapping, ST1/4-20×16 S=9.5 53 Washer,Bell,ij38×ij8×4
15 45rebbuR,leehW Key Flat,8X7×18
16 Guide Bracket, Front, Auger Cable 55 Pulley,Half
17. Guide Bracket, Auger Cable 56 Pulley,Auger
18 7504X01M,wercSxeH Spacer
19 85,lleB,rehsaW,01M Key Flat,8X7×14
20
Screw,Self-tapping,ST1/4-20×16 S=9.5 59
Pulley,Half
21 Ring E-Type,GB/T896-1986 17 60 V-belt
22 16orp-iH,yeK Screw,Self-Tapping,3/8-16×27 l=44 S=14
23 26ylbmessAraeG Pulley Step Shaft
24 3.6xeH,tfahSebirD Gasket
25 Roller Bracket,Dtive Cable 64 Bearing,6000-2RS
26 56revoCemarF Shell of Bearing
27 66tfihS,ylbmessAdoR Pulley Arm
28 Spring,Tensileij1.2×ij10×60
67 Spring,Reversion,ij2.2×ij27×7
29 Screw,Self-Tapping,ST1/4-20×16 S=9.5 68 Pulley Bush
30. 96tfahSraeG Only Back-chip, Plum
31 Dynamic Guard
70
Screw,Self-Tapping,ST1/4-20×16-
ij9.40×2.8-
ij13.7×2 S=9.5
32 17lleB,rehsaW Gasket
33 2702×8M,kooLxeH,tuN Screw,Self-Tapping,ST1/4-20×16 S=9.5
34 Screw,self-Tapping,5/16-18×19 S=12.5 73 Plate,Friction
35 Washer,Bellij24×ij 472×8 Friction Wheel Rubber
36 57epyT-EgniR Plate,Friction,Extrs
37. 67emarF Hub,Friction Wheel
38 Nut,Hex Look,3/8-16 S=14 77 Ring E-Type,GB/T 894.2 35
39 Screw,Self-tapping,ST1/4-20×16 S=9.5 78 Bearing Assembly,Friction Wheel
40 Nut,Hex Look,5/8-18 S=21 79. Gearing,6000-2RS
41 Spring,Tensileij1.2×ij10×35
80 Pin,Friction Disc Bearing,5/8-18×15-ij30×13