Use and Care Manual

28
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
5.21=S81-61/5,kooLxeH,tuN.33gniraeB,gnisuoH.1
edilS,eohS.43egnalF,gnihsuB.2
3. Washer,Bell,ij38×ij19.2×0.8 35. Nut,Hex Look,3/8-16 S=14
evahS,etalP.63egnalF,gnihsuB.4
5.9=S91×02-4/1gnippaT-fleS,wercS.73HL,ylbmessAlaripS.5
ylbmessArellepmI.83trohS,recapS.6
noisneT,mrA.93niPraehS.7
looTtuOnaelC,tnuoM.04elytS-B,niP.8
looTtuOnaelC.14gnoL,recapS.9
mulP,kcoLegnalF,tuN.24edistuO,liO,laeS.01
11. Housing.Auger,LH Reduced
43. Bolt,Carriage,5/16-18×51 dk=18
12. Hex Screw, 3/8-16×13-ij15.8×4.3 S=24
44. Nut,Flange Lock, Non-Metallic Piecesl5/16-18
S=12.5
rewoL,etuhC.5401M,sotsebsA,teksaG.31
reppU,etuhC.64llamS,egnalF,gniraeB.41
15. Washer,Flat,ij28×ij teviR.745.1×31 ij4x7
rewoL,etuhC,teksaGcitsalP.84mroW,tfahS.61
mulP,pihC-kcaBylnO.94lewoD,niP.71
elisneT,gnirpS.05tsurhT,ralloC.81 ij1.2×ij10×60
19. Washer,Bell,ij38×ij19.2×0.8
51. Nut,Hex Look,3/8-16×13-ij15.8×4.3 S=24
-31×61-8/3,kooLxeH,tuN.25giB,egnalF,gniraeB.02 ij15.8×4.3 S=24
21. Nut,Hex Look,5/16-18 S=12.5 53. Nut,Hex Look,3/8-16 S=14
yelluPreldL.458M,lleB,rehsaW.22
3/3-XBA4026,gniraeB.550101KH,gniraeB.32
24. Nut,Hex Look,5/16-18×16-ij10×16.5 S=12.6
56. Nut,Hex Look,5/16-18 S=12.5
retpadAyelluP.75liO,laeS.52
26. Sliding bearing, Knife Shaft 58. Hoursing,Bearing
27. Washer,Bell,ij38×ij19.2×0.8 59. Gasket, Wave-type,ij23×ij17×0.5
5.21=S22×42-61/5,kooLxeH,tuN.06orP-iH,yeK.82
,lleB,rehsaW.16mroW.92 ij38×ij8×4
30. Housing,Auger,RH Reduce
62. Pulley,Assembly
-61×61-8/3kooLxeH,tuN.36sixArettuC.13 ij12.5×8 S=19
32. Bolt,Carriage,5/16-18×13-8×8×4 dk=18
64. Nut,Hex Look3/8-16 S=14