Product Manual
Table Of Contents
- Powermate PM3800, PM4400E, PM4500 Portable Generator Owner’s Manual
- Table of Contents
- Section 1 Introduction and Safety
- Section 2 General Information and Setup
- Section 3 Operation
- Operation and Use Questions
- Before Starting Engine
- Prepare Generator for Use
- Grounding the Generator When Used as a Portable
- Know Generator Limits
- Transporting/Tipping of the Unit
- Starting Pull Start Engines
- Starting Electric Start Engines (if equipped)
- Low Oil Level Shutdown System
- Charging the Battery (electric start units only)
- Section 4 Maintenance and Troubleshooting
- Part No. A0000024084
- Generador portátil Powermate PM3800, PM4400E, PM4500 Manual del propietario
- Índice
- Sección 1 Introducción y seguridad
- Sección 2 Información general y configuración
- Sección 3 Operación
- Preguntas sobre la operación y el uso
- Antes de arrancar el motor
- Preparación del generador para su uso
- Conexión a tierra del generador cuando se utilice como equipo portátil
- Conozca los límites del generador
- Transporte/inclinación de la unidad
- Arranque de motores de arranque retráctil
- Arranque de motores de arranque eléctrico (si están equipados)
- Sistema de cierre por nivel bajo de aceite
- Carga de la batería (solo unidades de arranque eléctrico)
- Sección 4 Mantenimiento y solución de problemas
- N.° de pieza A0000024084
- Génératrice portable Powermate PM3800, PM4400E, PM4500 Manuel de l’utilisateur
- Table des matières
- Section 1 Introduction et sécurité
- Section 2 Généralités et configuration
- Section 3 Fonctionnement
- Questions concernant le fonctionnement et l’utilisation
- Avant de démarrer le moteur
- Préparer la génératrice à l’utilisation
- Mise à la terre de la génératrice lors d’une utilisation portable
- Connaître les limites de la génératrice
- Transport et inclinaison de la machine
- Démarrer un moteur à lanceur à rappel
- Démarrer un moteur à démarreur électrique (le cas échéant)
- Système d’arrêt en cas de faible niveau d’huile
- Recharger la batterie (machine à démarrage électrique seulement)
- Section 4 Entretien et dépannage
- Réf. A0000024084
10 Owner’s Manual for Portable Generator
3. Call Powermate Customer Service at 1-
800-445-1805 with the unit model and
serial number for any missing carton con-
tents.
4. Record model, serial number, and date of
purchase on front cover of this manual.
Assembly
Call Powermate Customer Service at 1-800-
445-1805 for any assembly issues or con-
cerns. Please have model and serial number
available.
The following tools are required to install the
accessory kit.
• 8mm Wrench
• 10mm Wrench
• 13mm Wrench
NOTE: The wheels are not intended for over-
the-road use.
See Figure 2-12.
Install wheels as follows:
1. Slide axle pin (E) through the wheel (B),
wheel bracket on frame, and 10mm flat
washer (G).
2. Insert cotter pin (F) through axle pin (E).
Bend tabs (of cotter pins) outward to lock
into place.
Install frame foot and rubber bumpers as fol-
lows:
1. Slide short bolts (K) through rubber
bumper (D), then through frame foot (C) (if
not assembled).
2. Slide long bolts (J) through holes in frame
rail.
3. Slide frame foot (C) onto long bolts (J).
Install locking flange nuts (H).
.
Figure 2-12. Wheel & Foot Assembly
See Figure 2-13.
Install handle as follows:
1. Slide long bolts (L) through handle bush-
ing (N) and handle (A). Install hex nuts
(M).
Figure 2-13. Handle Assembly
Battery Cable Connection
(electric start only)
The unit has been shipped with the battery
cables disconnected.
1. Cut off cable ties securing battery cables
and remove red cover from battery termi-
nal.
2. See Figure 2-14 (A). First, connect the red
cable to the positive (+) battery terminal
with the bolt and nut supplied.
3. Make sure connections are secure and
slide rubber boot over the positive (+) bat-
tery terminal and connection hardware.
4. See Figure 2-14 (B). Connect the black
cable to the negative (-) battery terminal
with the bolt and nut supplied. Slide rubber
boot over the negative (-) battery terminal
and connection hardware.
Hardware Bag Qty.
Rubber Feet (D) 2
10mm Axle Pin (E) 2
Cotter Pin (F) 2
10mm ID Flat Washer (G) 2
Hex Flanged M6 Nut (H) 6
M6 Bolt (Long) (J) 4
M6 Bolt (Short) (K) 2
M8 Bolt (L) 3
M8 Nut (M) 3
(000100a)
WARNING
Consult Manual. Read and understand manual
completely before using product. Failure to
completely understand manual and product
could result in death or serious injury.
E
F
K
H
H
J
C
G
009456
B
D
A
J
A
009690
M