Use and Care Manual

4
200-2756
SPECIFIC SAFETY RULES
CALIFORNIA PROPOSITION 65 WARNING
This product contains chemicals known to the State
of California to cause cancer, birth defects and/or
reproductive harm.
n Know your power tool. Read operator’s manual carefully.
Learn its applications and limitations, as well as the specific
potential hazards related to this tool. Following this rule will
reduce the risk of electric shock, fire, or serious injury.
n Drain tank of moisture after each day’s use. If unit will
not be used for a while, it is best to leave drain valve open
until such time as it is to be used. This will allow moisture
to completely drain out and help prevent corrosion on the
inside of tank.
n Risk of Fire or Explosion. Only spray flammable liquids
such as paints or lacquers. Never spray flammable liquids
in a confined area. Spray area must be well ventilated. Do
not smoke while spraying or spray where spark or flame is
present. Keep compressors as far from the spraying area
as possible, at least 15 feet from the spraying area and all
explosive vapors.
n Risk of Bursting. Do not adjust regulator to result in output
pressure greater than marked maximum pressure of
attachment. Do not use a pressure greater than maximum
rated pressure of compressor.
n If connected to a circuit protected by fuses, use time-
delay fuses with this product.
n To reduce the risk of electric shock, do not expose to
rain. Store indoors.
n Inspect tank yearly for rust, pin holes, or other
imperfections that could cause it to become unsafe.
Never weld or drill holes in the air tank.
n Make sure the hose is free of obstructions or snags.
Entangled or snarled hoses can cause loss of balance or
footing and may become damaged.
n Use the air compressor only for its intended use. Do
not alter or modify the unit from the original design or
function.
n Always be aware that misuse and improper handling of
this tool can cause injury to yourself and others.
n Never leave a tool unattended with the air hose attached.
n Do not operate this tool if it does not contain a legible
warning label.
n Do not continue to use a tool or hose that leaks air or
does not function properly.
n Always disconnect the air supply and power supply
before making adjustments, servicing a tool, or when a
tool is not in use.
n Do not attempt to pull or carry the air compressor by
the hose.
n Your tool may require more air consumption than this
air compressor is capable of providing.
n Never store tool with air connected. Storing the tool with
air connected can result in unexpected firing and possible
serious personal injury.
n Always follow all safety rules recommended by the
manufacturer of your air tool, in addition to all safety
rules for the air compressor. Following this rule will
reduce the risk of serious personal injury.
n Never direct a jet of compressed air toward people or
animals. Take care not to blow dust and dirt towards
yourself or others. Following this rule will reduce the risk
of serious injury.
n Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
n Do not use this air compressor to spray chemicals. Your
lungs can be damaged by inhaling toxic fumes. A
respirator may be necessary in dusty environments or when
spraying paint. Do not carry while painting.
n Inspect tool cords and hoses periodically and, if
damaged, have repaired at your nearest Authorized
Service Center. Constantly stay aware of cord
location. Following this rule will reduce the risk of electric
shock or fire.
n Never use an electrical adaptor with this grounded plug.
n Check damaged parts. Before further use of the air
compressor or air tool, a guard or other part that is
damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center. Following this rule will reduce the risk of shock, fire,
or serious injury.
n Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 50 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating.
n Save these instructions. Refer to them frequently and use
them to instruct others who may use this air compressor. If
you loan someone this tool, loan them these instructions also.