DUST COLLECTOR Model 75 Instruction Manual & Parts List M-0460200 (800) 248-0144 www.powermatic.
This manual has been prepared for the owner and operators of a Powermatic Model 75 Dust Collector. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your dust collector and to aid in using the machine safely, read this manual thoroughly and follow all instructions carefully.
TABLE OF CONTENTS Safety Rules ...................................................................................................................................... 4-5 Safety Decals ....................................................................................................................................... 6 Specifications ........................................................................................................................................ 7 Receiving ..........................
! SAFETY RULES Read the Manual. Always read the owner's manual carefully before attempting to use the machine. Know the limitations and hazards associated with its use. Eyes. Always wear approved safety goggles or glasses that comply with ANSI Z87.1 when operating this machine. NOTE: Common eyeglasses are only impact resistant, they are not safety glasses. Dress Code. Do not wear loose clothing, neckties, jewelry, or gloves that can get caught in moving parts. Confine long hair.
Do not put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow. Drugs, alcohol, medication. Do not operate machine while under the influence of drugs, alcohol, or any medication. Health Hazards. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
! SAFETY Familiarize yourself with the location of these safety decals on your dust collector.
SPECIFICATIONS: Model 75 Dust Collector Motor .................................................................................................. 3 HP, 1 Ph, 230V .................................................................. 3 HP, 3 Ph, 230/460V (prewired 230V) CFM ........................................................................................................................ 1900 Capacity ...........................................................................................................
FIGURE 1 RECEIVING Hex Head Screw M8 x 1.25 x 20 Qty. 48 Remove all contents from the shipping carton and check each item against the packing list. Report any missing or damaged parts immediately to your shipping agent and distributor. Read the instruction manual thoroughly for assembly, alignment, maintenance and safety instructions.
ASSEMBLY Tools needed 13mm wrench pliers 1. Turn the base on edge and attach the four caster assemblies to the threaded holes in the corners of the base. The loose nut and washer on the caster should be removed and reversed (washer on top of nut) as shown in Figure 3. Place a wrench on the bottom nut and turn clockwise to screw the caster assembly firmly into the base. 2. Mount the two extension plates to the ends of the base, each with four screws, four flat washers, four lock washers, and four hex nuts.
4. Turn the base upright on to its casters. Attach the two support brackets to the threaded holes in the center of the base, as shown in Figure 6. Use four screws with four flat washers. NOTE: Be careful not to strip the screws. FIGURE 6 5. With the aid of an assistant, lift the impeller housing with motor on to the support brackets, dropping the four bolts mounted to the impeller housing into the four holes in the support brackets. See Figure 7.
7. Attach two of the support legs to the front of the machine. See Figure 9. The bottom of the support leg is slotted and mounts to the pre-tapped holes in the base with two screws and two flat washers. Do not tighten yet. The top of the support leg mounts to the housing with two screws, four flat washers, and two nuts. Use the slots at the bottom of the support leg for adjustment if needed, then tighten all screws and nuts. FIGURE 9 8.
11. Install the lower dust bag as follows: Insert a retainer strap through the loops in the bag as shown in Figure 13. ! CAUTION: Retainer straps are rolled up under tension. Hold strap with hand and allow to unroll gradually. Place the bag over the lip of the housing and secure by fastening the retainer strap. Repeat for other lower bag. FIGURE 13 12. In the same fashion, install the upper bag with a retainer strap over the top lip of the housing. (NOTE: the upper bag has the Powermatic name on it).
GROUNDING INSTRUCTIONS ! WARNING: The dust collector must be grounded to protect the operator from electric shock. Not all outlets are properly grounded. Have your outlets checked by a qualified electrician. All grounded, cord connected tools: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current in order to reduce the risk of electric shock.
Trouble-Shooting for Model 75 Dust Collector PROBLEM POSSIBLE CAUSE SOLUTION Motor will not run. 1. Defective cord, plug, switch, and/or motor. 1. Consult service. Any attempt to repair this motor may create a hazard unless repair is done by a qualified service technician. 2. Check for blown fuses and replace with fuse of proper capacity or re-set circuit breaker. 2. Blown fuse or circuit breaker tripped. Excessive sawdust in air. 1. Loose clamps; dust bag and/or chip collection bag not secure. 1.
Parts List: Model 75 Dust Collector No. Part No.
Parts List: Model 75 Dust Collector No. Part No. Description 54 55 56 57 58 59 60 61 6286612 6286615 6286614 6286613 6286616 6286617 6286630 M-0460200 Hose, 20' x 4" ........................................................................................................ 1 Clamp, 4" .............................................................................................................. 1 Adapter, 4" - 4 ...............................................................................................
Model 75 Dust Collector 17
Optional Accessories 6050011 6286600 6286601 6286602 6286618 6292835 18 Collector (lower) bags, clear plastic (50 each) Filter (upper) bag, cloth (1 each) Collector (lower) bag, clear plastic (1 each) Vacuum attachment (20' hose with 12" vacuum head) Adaptor for 8" to 6" Collector (lower) bag, cloth (1 each)
To order parts or reach our service department, please call our toll-free number between 8:00 a.m. and 4:30 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Locating the stock number of the part(s) required from your parts manual will also expedite your order. Phone No.: (800) 248-0144 Fax No.
10/2001 WMH Tool Group 427 Sanford Road LaVergne, TN 37086 Phone: (800) 248-0144 Fax: (800) 274-6840 E-mail: powermatic@wmhtoolgroup.com Website: www.powermatic.
