This .pdf document is bookmarked Instructions and Parts Manual PM1900TX Dust Collector Now with PM1900TX with Filter Bag Kit (1792071K) Powermatic 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.powermatic.com PM1900TX with Canister Kit (1792072K) Part No.
adjusting wrenches are removed from the machine before turning it on. IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce the risk of fire, electric shock, or injury: 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4.
6. Do not stand on the machine. Serious injury could occur if the machine tips over. 28. Do not use without dust bag and/or filters in place. 29. Do not handle plug or machine with wet hands. WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www. p65warnings.ca.gov. 30. Do not put any objects into the openings.
Table of Contents IMPORTANT SAFETY INSTRUCTIONS ...................................................................................................... 2 Table of Contents .......................................................................................................................................... 4 Introduction.................................................................................................................................................... 5 Specifications ......................
Introduction This manual is provided by Powermatic covering the safe operation and maintenance procedures for a Powermatic Model PM1900TX Dust Collector. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this manual.
Unpacking Remove all contents from the shipping carton and check against the Contents of Shipping Carton below to verify that all items have been received. Report any damage to your distributor. Do not discard any shipping material until after the dust collector has been assembled and is running properly. You will also require either the Filter Bag System or Canister Filter System. These items are packaged separately and are not listed here.
3. Insert an M8x20 hex cap screw (A), through the M8 washer (D) and flanges of the connector tube (R) and impeller housing (N). 4. Place another washer (D) and a hex nut (F) on the protruding end of the screw (A) and handtighten only. 5. Mount the control box (S) to the two holes at the front of the connector tube flange (R). 6. Repeat steps 3 and 4 for the remaining screw locations, hand tightening only. 7. Tighten all hex nuts with a 13mm wrench.
Handles Cone Installation 1. Remove the plate (Y) from the handle (X) by loosening the two socket head cap screws (Z) with a 6mm hex wrench. 2. Install handle (X) to the holes in the collector housing (U) by inserting the socket head cap screws through the handle, the collector housing, and into the plate on the opposite side. Tighten the screws. Note: Make sure the plate (Y) is oriented properly, as shown in the Detail in Figure 3: The protrusions on the plate should face away from the handle. 3.
. Thread the retainer strap (Figure 6) through the loops on the filter bag, and fasten it to the collector housing, as shown in Figure 7. Filter Bag System Assembly Note: If your dust collection system includes the canister kit, proceed to Canister System Assembly on page 10. 1. Insert a hanger bracket between support bar and collector housing (Figure 4). 2.
Canister System Assembly (17mm wrench required) 1. Place the snap ring over the top of the plastic collector bag, and fold over the bag approximately three inches (Figure 8). Figure 9 Figure 8 2. Insert the snap ring of the collector bag into the bottom of the housing at an angle (Figure 9). 3. Pull down on the snap ring to make sure it “seats” on the inner lip of the housing.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possible fatal injury. Repair or replace a damaged or worn cord immediately.
Cleaning the Filter Bags NOTE: The infrared sensor on the dust collector has a 120° line-of-sight angle. See Figure 12. Outside of this angle, the remote control may not be effective. Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended. During first use and after cleaning, the filter bags may allow some dust to escape. This is normal and will stop after a short period of time.
Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-2746848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from Powermatic.
Parts List for PM1900TX Dust Collector (Base Machine) Index No. Part No. Description Size Qty 1 ............... PM1900-101 ............ Impeller Housing .................................................. .................................... 1 2 ............... PM1900-102 ............ Impeller Housing Bracket ..................................... .................................... 1 3 ............... PM1900-103-1 ......... Motor Bracket ....................................................... 1Ph.......
Index No. Part No. Description Size Qty 37 ............. TS-1490031 ............. Hex Cap Screw .................................................... M8x20 ....................... 36 38 ............. TS-1490041 ............. Hex Cap Screw .................................................... M8x25 ......................... 4 39 ............. PM1900-139 ............ Magnetic Switch ................................................... for 3HP, 230V, 1Ph ..... 1 39-1 .......... PM1900-139-1 .........
Parts List and Breakdown for PM1900TX Filter Bag System Index No. Part No. Description Size Qty ................. 1791075B ................. Collection and Filter Bag System (includes #1 thru 6) .............................. 1 1 ............... 1791075F ................. Filter Bag .............................................................. 30 micron .................... 2 2 ............... 430005 ..................... Retainer Strap ...................................................... ...........
Breakdown for PM1900TX Canister Filter System 17
Parts List for PM1900TX Canister Filter System Index No. Part No. Description Size Qty ................. 1791086 ................... Canister Filter System (includes #1 thru 24)........ .................................... 2 1 ............... PM1900-301 ............ Canister Filter ....................................................... .................................... 1 2 ............... PM1900-302 ............ Knob ..................................................................... M6x20 .......
Electrical Connections Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
Warranty and Service Powermatic® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official Powermatic branded website. • Powermatic products carry a limited warranty which varies in duration based upon the product.
