PPC Series Manual

ManualsBrandsPowerMax ManualsSolar & Wind Power35 Amp 12VDC Power Center with Lower Converter and Smart Charger

without notification

AC/DC Distribution Panel

with Converter & Charger

AC/DC DISTRIBUTION PANEL

with

CONVERTER & CHARGER

PPC models: 35, 45, 55, 75 and 100

Amp with 3 Stage Charging

Installation & Maintenance

SAFETY ALERT

FOR YOUR SAFETY, READ ALL INSTRUCTIONS BEFORE INSTALLATION AND OPERATION.

INSTALLER: Provide these instructions to the end user or consumer.

CONSUMER: Keep these instructions for future reference.

NOTICE: Products are not to be used nor are warranted in aerospace, medical or life safety applications.

WARNING – Avoid Personal Injury or Product Damage

NEVER store electrical devices in compartments where flammable liquids (such as gasoline) exist.

DO NOT mount/install unit in compartments designed for storage of batteries of flammable liquids.

1. DISCONNECT RV DC POWER. Disconnect the RV battery POS (+) wire at the battery end before connecting this

Converter/Charger and Distribution Panel to any RVwiring.

2. LOCATION. The mounting location may be on any interior (out of direct weather) surface. Location chosen must be accessible

after installation. When mounted inside a cabinet, the cabinet must be large enough to allow dissipation of heated air. Make

sure that there is a minimum of 1” (one inch) free air space at each end of the unit so that cooling air can move through the unit

properly. AVOID foreign contaminants such as dirt, metal particles or moisture.

3. MOUNTING. Flanges with holes are provided for ease of mounting using standard fasteners. Confirm that the surface that the

Distribution Panel with converter is mounted to is solid and will hold the weight (14 lbs) during vehicle operation.

4. ELECTRICAL REQUIREMENTS. For PPC models, a 120 VAC with 30 Amp source, preferably a separate breaker, is required

to supply power. Electrical consideration should also be given to mounting near the locations of the RV batteries and the 12-

VDC distribution panel.

5. ELECTRICAL CONNECTIONS. Be sure to tighten all connections securely. A loose connection can quickly cause terminals

and wires to overheat.

WARNING – Avoid Possible Injury or Death

120 VAC is present. This Converter/Charger is designed to convert 120 VAC to 12 VDC. It also provides low voltage

power for charging on-board 12 VDC batteries. The SRV series Converter/Charger is a “switch mode” type and is

designed to be maintenance-free with no user serviceable components. The Converter/Charger power output is “current

limiting” by design.

The Converter/Charger is integrated with a 120 VAC and 12 VDC Distribution Panel that allows easy installation and

centralizes all power connections. Stab type AC breakers with branch circuits are used. The DC fuse block has individually

fused branch circuits. The Converter/Charger can easily be removed without removing the Distribution Panel wiring.

Summary of content (4 pages)

PAGE 1
AC/DC DISTRIBUTION PANEL with CONVERTER & CHARGER PPC models: 35, 45, 55, 75 and 100 Amp with 3 Stage Charging AC/DC Distribution Panel with Converter & Charger Installation & Maintenance SAFETY ALERT FOR YOUR SAFETY, READ ALL INSTRUCTIONS BEFORE INSTALLATION AND OPERATION. INSTALLER: CONSUMER: Provide these instructions to the end user or consumer. Keep these instructions for future reference. NOTICE: Products are not to be used nor are warranted in aerospace, medical or life safety applications.
PAGE 2
WARNING – Avoid Possible Injury or Death 120 VAC Connection – First confirm that the 120 VAC power source AC circuit breaker(s) are in the off position. DO NOT turn-on AC circuit breakers until installation is complete. Using an 8 AWG minimum size copper wire, attach from the RV chassis to the chassis bar inside the Distribution Panel. Connect the 120 VAC power source to the AC circuit breakers that are mounted inside the Distribution panel.
PAGE 3
PPC DISTRIBUTION PANEL PLASTIC CASE BATTERY NEGATIVE CONNECTION (OUTPUT-GND) White Wire DC OUTPUT AC INPUT FUSE PANEL AC CIRCUIT BREAKERS GROUND TERMINAL BAR NEUTRAL TERMINAL BAR REVERSE BATTERY FUSES BATTERY POSITIVE CONNECTION(OUTPUT-12V+) Red Wire Positive for DC Applicance (OUT1~OUT11) White Wire- (INPUT-GND) Blue Wire+ (INPUT-12+) White Wire (N) - CHARGER AREA Black Wire (L) Yellow& Green (G) Copyright© 2014, Fieldstone Products, LLC.
PAGE 4
TWO YEAR LIMITED WARRANTY Limited Warranty and Remedy: Fieldstone Products,Inc (“Supplier”) warrants products of its own manufacture against faulty workmanship or the use of defective materials and that such products will conform to mutually agreed upon specifications, drawings and other descriptions for a period of two years.