Use and Care Manual

ManualsBrandsPOWERNAIL ManualsKitchen20-Gauge Pneumatic Hardwood Flooring Trigger Pull Stapler Kit

Read this manual before you use this Stapler.

Follow all safety warnings and instructions. Do not

attempt any disassembly or repairs while the air

line is connected. Always disconnect the air line

rst. Do not use excessive unregulated air pressure.

If you are uncertain about the operation of the

Stapler, call us directly a 1-800-323-1653 for

assistance or contact the closest Powernail

Dealer

for help. Please retain this information for future

reference.

WARNING

REV 10.07.01

Operation and Maintenance Manual

Models 20FS Pneumatic PowerStapler™

POWERNAIL

CO.

1300 Rose Road, Lake Zurich, IL 60047

Phone: 1-800-323-1653

Website: http://www.powernail.com

Summary of content (8 pages)

PAGE 1
POWERNAIL® CO. 1300 Rose Road, Lake Zurich, IL 60047 Phone: 1-800-323-1653 Website: http://www.powernail.com Operation and Maintenance Manual Models 20FS Pneumatic PowerStapler™ WARNING Read this manual before you use this Stapler. Follow all safety warnings and instructions. Do not attempt any disassembly or repairs while the air line is connected. Always disconnect the air line first. Do not use excessive unregulated air pressure.
PAGE 2
DESCRIPTION The PowerStapler® Model 20FS trigger pull stapler is the latest model designed to bring Powernail quality and flooring expertise to a pneumatic Stapler. The PowerStapler Model 20FS is designed for use with 1”, 20 gauge PowerStaples®. The Model 20FS can staple down from 3/8” to 1/2” flooring through the use of an easy-to-adjust foot that can be adjusted to fit different flooring profiles.
PAGE 3
OPERATING INSTRUCTIONS Figure 1. FOOT ADJUSTMENT / STAPLE LOCATION Loosen both adjusting knobs (76) Hold stapler on sample piece of sample flooring to be installed. Adjust the face pad (74) so it lays flat on the finished surface of the flooring (Fig 1). Lightly snug both adjusting knobs (76). Push down on front stand (73) so it lays flat on the sub floor. Tighten both adjusting knobs (76).
PAGE 4
OPERATION (continued) LOADING THE FASTENERS 1. Depress the LOCK(60) to release the MOVABLE 60 MAGAZINE (44) and pull the magazine out fully as shown in Figure 3. 2. Place a full clip of the specified type and size fasteners on the FIXED MAGAZINE (51), up to 125 fasteners may be loaded in the magazine. 3. Push the MOVABLE MAGAZINE ASSEMBLY forward until it is locked.
PAGE 5
REGULAR MAINTENANCE 1. Frequent, but not excessive, lubrication is required for best performance. Oil added through the airline connection will lubricate internal parts. An automatic airline oilier is recommended but oil may be added manually before every operation or after about 1 hour of continuous use. Only a few drops of oil at a time are necessary. Too much oil will collect inside the tool and be blown out during the exhaust cycle. ONLY USE PNEUMATIC TOOL OIL.
PAGE 6
Model 20FS SCHEMATIC 1 66 2 14a 3 4 65 22 64 63 14b 60 62 15 5 59 27 28 29 6 30 7 32 31 33 34 35 24 8 25 17 9 10 36 18 11 37 38 39 12 58 57 61 1 31 23 16 36 55 54 46 53 43 44 52 43 45 13 19 51 14 49 50 78 79 76 71 74 73 72 77 75 6 56
PAGE 7
PARTS LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 14a 14b 15 16 17 18 19 22 23 24 25 27 28 29 30 31 32 33 34 35 36 37 38 39 43 44 45 DESCRIPTION Screw Bushing Exhaust Cover Seal Screw Cylinder Cap Gasket Seal Spring O-Ring 36.3x2.5 O-Ring 15.7x2 Valve O-Ring 33.5x3.5 Stopped Washer O-Ring 48.5x2.5 Collar O-Ring 48.5x2.5 Piston Assembly O-Ring (27.3x2) Cylinder Bumper Body Joint Guider Safe Bracket Guider Spring Pin Seal Trigger Valve Head Spring O-Ring (5.5x1.5) Trigger Valve Stem O-Ring (15x1.
PAGE 8
TROUBLE SHOOTING CHART Here are some common issues may occur during use. If the stapler is not working as it should be, stop using the tool immediately and resolve the issue before continuing. PROBLEM 1 Air leaking at Trigger area POSSIBLE CAUSE SOLUTION 1. O-ring in trigger valve is damaged. 1. Check and replace O-ring. 2. Trigger valve head is damaged. 2. Check and replace trigger valve head. 3. Trigger valve stem, seal or O-ring is damaged 3.