Use and Care Manual

ManualsBrandsPOWERNAIL ManualsKitchen16-Gauge Pneumatic Hardwood Flooring Cleat Nailer

Read this manual before you use this Nailer.

Follow all safety warnings and instructions. Do

not attempt any disassembly or repairs while

the air line is connected. Always disconnect the

air line rst. Do not use excessive unregulated

air pressure. If you are uncertain about the

operation of the Nailer, call us directly a 1-800-

323-1653 for assistance or contact the closest

Powernail

Dealer for help. Please retain this

information for future reference.

WARNING

REVISION G3-102709

Operation and Maintenance Manual

Models 445 XLL, XLS, LL, LS, SL, SS, & SN

Pneumatic Powernailer

POWERNAIL

CO.

1300 Rose Road, Lake Zurich, IL 60047

Phone: 1-800-323-1653

Website: http://www.powernail.com

Operation and Maintenance Manual

REVISION G.3—0805

WARNING

Read this manual before you use this Nailer. Follow all

safety warnings and instructions. Do not attempt any

disassembly or repairs while the air line is connected.

Always disconnect the air line first. Do not use excessive

unregulated air pressure. If you are uncertain about the

operation of the Nailer, call us directly at 1-800-323-1653

for assistance or contact the closest Powernail

Dealer for

help. Please retain this information for future reference.

POWERNAIL

CO.

1300 Rose Road, Lake Zurich, IL 60047

phone: 1-800-323-1653

website: www.powernail.com

MODELS 445 XL, XS, LL, LS, SL, SS & SN

PNEUMATIC POWERNAILER

REVISION G.3

For this parts list and other Powernailer schematics, please visit the

Powernail Parts Store at http://www.powernail.com

Summary of content (13 pages)

PAGE 1
® CO. ® CO. POWERNAIL POWERNAIL 1300 Road, Rose Road, Lake Zurich, IL 60047 1300 Rose Lake Zurich, IL 60047 Phone: 1-800-323-1653 phone: 1-800-323-1653 website: www.powernail.com Website: http://www.powernail.com Operation and Maintenance Manual Operation and Maintenance Manual Models 445 XLL, XLS, LL, LS, SL, SS, & SN MODELS 445 XL, XS, LL, LS, SL, SS & SN PneumaticPOWERNAILER Powernailer® ® PNEUMATIC REVISION G.
PAGE 2
TO PREVENT ACCIDENTAL INJURIES: Always wear approved front and side EYE PROTECTION when operating this Nailer. Others in the work area should also wear front and side EYE PROTECTION. Eye protection will help guard against flying nails and debris, which could cause severe eye injury. THE TRIGGER IS A SAFETY DEVICE and should only be pulled when the Nailer is in proper position on the work surface and before the plunger is struck with the mallet.
PAGE 3
OPERATION Read these instructions carefully before you use the Nailer. WARNING Whenever air is connected to the Nailer, keep body parts away from the nail discharge path. Disconnect the air line before making adjustments or repairs on the Nailer. Only connect air to an unloaded Nailer so as to prevent accidental discharge. Consult the drawing for the appropriate adapter pad to use with the thickness of flooring you are installing.
PAGE 4
TO LOAD MODEL 445 XLL, LL or SL: Place up to two sticks (200 Powercleats) into the Nail Channel feed slot. Pull back the spring loaded Nail Pusher over the nails until it contacts the last nail and slowly release the Nail Pusher. NEVER FIRE THE NAILER WITHOUT THE RUBBER BUMPER INSTALLED, IT WILL SEVERELY DAMAGE THE NAILER. TO REPLACE DRIVING BLADE (#14): 1. Disconnect the air supply. TO LOAD MODEL 445 XLS, LS or SS: Place one stick (100 Powercleats) into the Nail Channel feed slot. 2.
PAGE 5
6. Plunger Wiper Seal (#25) 7. Return Cylinder O-Ring Gasket (#26) direction of the chamfer when you replace the Rubber Seat. To change Seals follow these procedures. Be sure the air line is disconnected from the Nailer first before making any repairs. 3. Replace the Rubber Seat, Support Ring and Cylinder Sleeve.
PAGE 6
The U-Cup Lip Seals #23 and #24 look alike, but they are different, DO NOT mix them up. respective cavities. Be sure the Seals are contained in their groove and do not come out as the parts slide together. Generous cavity lead in chamfers have been provided to help Seal installation. 3. Carefully wipe off the Lip Seal surface with a clean rag and lubricate it generously with the supplied Mobile DTE Light Air Tool Oil lubricant. 4.
PAGE 7
3. Separate the Foot and gate with a screw driver just enough to clear out the jammed nail. 4. Put thread locking compound on all screws and reassemble the components.
PAGE 8
MODELS 445 XLL, XLS, LL, LS, SL, SS & SN PARTS LIST ITEM # PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 09-445-29701 09-445-29702 09-445-29703 09-445-29703.
PAGE 9
MODELS 445 XLL, XLS, LL, LS, SL, SS & SN PARTS LIST ITEM # 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 PART NO. 09-445-29751 09-445-29754 09-445-29832 09-445-29756 09-445-29757 09-445-29758 09-445-29759 09-445-29760 09-445-29790 09-445-29791 09-445-29792 09-445-29795 09-445-29796 09-445-29797 09-445-29798 09-445-29799 09-445-29822 09-445-29836 09-445-29819 09-445-29738.1 DESCRIPTION QTY.
PAGE 10
SCHEMATIC MODELS 445 XLL, XLS, LL, LS, SL, and SS 10
PAGE 11
SCHEMATIC 445 SN SURFACE NAILER 11
PAGE 12
POWERCLEATS LENGTH DETERMINATION CHART This chart will assist you in determining the proper length of Powercleats to use for various thicknesses of flooring. Approximate vertical penetration of the Powercleat under the hardwood floor is shown for each application. This is only a guide. Results should be tested in the field before proceeding.
PAGE 13
POWERNAILER MODEL 445 TROUBLE SHOOTING CHART PROBLEM POSSIBLE CAUSE SOLUTION Check air supply for 70 psi minimum to 110 psi maximum 2. Lack of lubrication Manually lubricate through male air inlet fitting Driving blade 3. Excessive dirt inside nailer Disassemble and clean does not retract 4. Bent or burred driving blade Replace driving blade 5. Seals worn out Replace all seals 6. U-Cup Lip Seals installed upside down Replace all seals 1. Low air pressure Turn up air pressure to 70-110 psi max 2.