Streetrod Gas Pressure Washer Owner’s Manual TO PREVENT DAMAGE AND BODILY HARM, ENSURE ENTIRE MANUAL HAS BEEN READ BEFORE OPERATION OF PRESSURE WASHER UNIT. WWW.POWERPLAYPRO.COM vers.
Questions? If you have questions or if there are missing parts, please call: 1-855-770-PLAY (7529) Or email: info@powerplaypro.
TABLE OF CONTENTS Warning 1 Safety 2-3 Assembly and Pre-start Procedures 4 Assembly and Pre-Start Checklist Initial Start-up Procedures Spray Tips - Spray Tip Applications 5 Soap Detergent Injector 6 Detergent Operations Using the Pressure Washer to Clean Maintenance Guideline 7 Recommended Engine Oil Engine Oil Replacement Inspecting and Replacing the Spark Plug Storage 8 Damage Prevention Longer-term Storage Limited Warranty POWERPLAY™ Corporat
WARNING Failure to read and follow the Owner’s Manual and all operating instructions can result in death, bodily injury, and/or property damage. Warning Running engines give off carbon monoxide an odourless, colourless, poison gas. Breathing carbon monoxide can cause headache, fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death. • Operate this product ONLY outdoors. • Keep exhaust gas from entering a confined area through windows, doors, ventilation intakes or other openings.
SAFETY A pressure washer is a power tool that sprays water at high pressure to clean large, sturdy surfaces such as buildings, farm equipment and roads. Pressure washers may be used more often during a natural disaster clean-up; the risk of injury may be higher at that time. When using a pressure washer, always follow the safety instructions included in the Owner’s Manual. Risks • The strong spray from a pressure washer can cause serious wounds that might first appear minor.
Safety Recommended Types of Eye Protection • Always wear eye protection. • Before selecting appropriate eye protection for users at a job site, assess the conditions and hazards and follow these recommendations: • At the very least, wear safety glasses with side protection. • Wear goggles when more protection is needed. • Consider using hybrid eye safety products with the comfort of glasses, the enclosure of goggles, and better breathability.
ASSEMBLY AND Start-up PROCEDURES WARNING! This pressure washer has been shipped from the factory without oil. Please refer to the Engine Owner’s Manual for correct checking, fill and specifications for engine oils. Assembly and Pre-start 1. Remove the pressure washer from the shipping package and appropriately dispose of the shipping container. 2. Inspect machine for any shipping damage and report to point of purchase retailer immediately. 3.
SPRAY TIPS ANGLE COLOUR PRESSURE USAGE 0° RED MAXIMUM HEAVY DUTY 15° YELLOW HIGH ROUGH SURFACE 25° GREEN MEDIUM VINYL AND WOOD 40° WHITE DELICATE VEHICLE SOAP BLACK LOW WITH DETERGENT Spray tip combinations may vary by model. Your Powerplay™ pressure washer has multiple attachments. Pressure washers operate on pressure (PSI) and volume of water (GPM) that is supplied to the soiled area that requires cleaning. Depending on the job, you can select from different quick-change tips.
DETERGENT INJECTOR Using water only can complete some cleaning jobs, but for most job requirements, a detergent is recommended in order to penetrate and remove the dirt more effectively. When using a pressure washer approved detergent, make sure the surface is dry. Wetting the surface first is not recommended. It will dilute the detergent and will reduce the cleaning effectiveness. Avoid hot surfaces or direct sunlight. This will minimize the chances of the detergent damaging the painted surface.
Maintenance guideline * See Engine Owner’s Manual for recommended maintenance Legend: H: HONDA R: RATO P: POWERPLAY Maintenance Items Each Use Check pump oil level H,B,P, R Check pump oil quality (for discolouration or contamination) H,B,P, R Check for pump oil leaks - inspect oil seals, drain, plug, oil plug, sight glass H,B,P, R Check for water leaks under manifold, into crankcase H,B,P, R Plumbing H,B,P, R Clean engine and check nuts and bolts H,B,P, R Check and refill engine
STORAGE Damage Prevention If your pressure washer is subjected to freezing temperatures, damage could occur. This type of damage is not covered under warranty. To avoid possible damage, a small amount of antifreeze can be used. Place the unit on its side with the water inlet facing upwards. Pour 1/4 cup of antifreeze into the water inlet. Disconnect spark plug wire. Pull recoil starter several times to circulate the antifreeze in the pump system. Reconnect spark plug wire.
POWERPLAY™ LIMITED WARRANTY PowerPLAY™ Corporation warrants that each product sold is free of defects in material and workmanship under normal use and service. Transportation charges on product submitted under this warranty must be assumed by the purchaser. This limited warranty becomes effective from the date of purchase. Please find below, a list of products with their corresponding warranties.
POWERPLAY™ LIMITED WARRANTY • Exposure of the product to soot and smoke, chemical agents, sea water, sea breeze, salt or other environmental phenomena. • Fuel contamination or deterioration, neglect, unauthorized alteration, misuse, incorporation or use of unsuitable attachments or parts. • Normal wear and tear (normal fading of painted surfaces or other natural deterioration). 2.
GAS-POWERED WASHER COMPONENTS Spray Storage Gun Holder Engine Hose Storage Detergent Tank Rubber Vibration Absorber Refer to Engine Owner’s Manual for Engine Components 24 21 23 22 33 32 2 35 25 34 1 15 32 11 31 3 ITEM 20 9 SOAP TANK SUBASSEMBLY 20 5 30 14 28 16 27 12 26 29 17 26 8 19 19 4 18 7 10 6 13 ITEM 21 HANDLE TUBE SUBASSEMBLY
PARTS GUIDE FOR STREETROD™ 12 - English
PARTS GUIDE FOR STREETROD™ **You can buy sub-assemblies 20 and 21, or buy the parts separately. Parts can be changed without notice.
TROUBLESHOOTING GUIDE PROBLEM CAUSE CORRECTION Engine will not start or stops while operating 1. Low-oil shutdown (if equipped) 2. Engine switch not in “ON” position 3. Pressure built up in the hose 1. Fill engine with oil 2. Turn switch “ON” 3. Squeeze trigger while starting Engine is overloaded 1. Nozzle partially blocked 2. Excessive pressure 1. Clean nozzle 2. Adjust unleader cartridge if adjustable Pressure increases when gun is closed 1. Bypass valve is blocked 1.
PRODUCT INFORMATION Thank you for purchasing from the PowerPLAY™ Corporation. You have selected the Powerplay™ series Pressure Washer. We ask that you fill out the following information to ensure warranty support. Being the owner of a PowerPLAY™ Product you have access to our nationwide dealer network for service, support and to purchase available items for purchase, such as accessories and detergents.