User Manual

ManualsBrandsPowerplus ManualsPower sawsPOW8002 MITRE SAW 1400W 210MM EN

POW8002 EN

1 DESCRIPTION (FIG A) .................................................................... 3

2 PACKAGE CONTENT LIST ............................................................. 3

3 SYMBOLS ........................................................................................ 4

4 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4

4.1 Working area ........................................................................................................... 4

4.2 Electrical safety ....................................................................................................... 4

4.3 Personal safety ....................................................................................................... 5

4.4 Power tool use and care ......................................................................................... 5

4.5 Service ..................................................................................................................... 5

5 SPECIFIC SAFETY WARNINGS ..................................................... 5

6 ASSEMBLY ...................................................................................... 6

6.1 Bench mounting ...................................................................................................... 6

6.2 Release knob ........................................................................................................... 6

6.3 Spindle lock lever.................................................................................................... 6

6.4 Blade replacement .................................................................................................. 7

6.5 Fitting the dust bag ................................................................................................. 7

7 ADJUSTMENTS ............................................................................... 7

7.1 Setting bevel angle ................................................................................................. 7

7.2 Setting mitre angle .................................................................................................. 7

7.3 Calibrating the bevel angle gauge ......................................................................... 8

8 OPERATION ..................................................................................... 8

8.1 Sawing ..................................................................................................................... 8

8.2 Fitting the work piece support ............................................................................... 9

9 CLEANING AND MAINTENANCE ................................................... 9

9.1 Cleaning................................................................................................................... 9

9.2 Maintenance ............................................................................................................ 9

10 TECHNICAL DATA ........................................................................ 10

11 NOISE ............................................................................................. 10

12 WARRANTY ................................................................................... 10

13 ENVIRONMENT ............................................................................. 11

Summary of content (12 pages)

PAGE 1
POW8002 EN 1 DESCRIPTION (FIG A) .................................................................... 3 2 PACKAGE CONTENT LIST ............................................................. 3 3 SYMBOLS ........................................................................................ 4 4 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4 4.1 Working area ........................................................................................................... 4 4.
PAGE 3
EN POW8002 MITRE SAW 1400W POW8002 WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. Your power tool should only be given to other users together with these instructions. 1 DESCRIPTION (FIG A) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Removable blade guard Lock lever for removable blade guard Handle Carbon brush cover 90°angle adjustment screw Fence Angle gauge Saw table Surface protector Mounting hole Switch Guard 13. 14. 15. 16. 17.
PAGE 4
EN POW8002 3 SYMBOLS The following symbols are used in this manual and/or on the machine: Denotes risk of personal injury or damage to the tool. Read manual before use In accordance with essential safety standards of applicable European directives Class II - The machine is double insulated; Earthing wire is therefore not necessary. Wear noise protection Wear eye protection 4 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions.
PAGE 5
EN POW8002 4.3 Personal safety  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when operating a power tool may result in serious personal injury.  Use safety equipment. Always wear eye protection.
PAGE 6
EN POW8002                  For your safety; remove the chippings and work debris etc. from the table top and from inside the extraction port before each operation. Avoid cutting nails; Remove all nails from the work-piece before cut ting. Make sure the shaft lock is released before switching on the saw. Be sure that the blade does not come into contact with the base when the blade is in the lowest position. Hold the handle firmly. Do not perform any operation freehand.
PAGE 7
EN POW8002 6.4 Blade replacement Note: Before replace the saw blade, turn off the switch and disconnect the plug from the power outlet.      Fig. 3 6.5 Press the spindle lock lever (19) to activate it, turn the saw blade by hand until it locked. Loosen the blade lock bolt by turning it clockwise using the spanner (supplied). Remove the lock bolt, outer flange, saw blade and inner flange . Remove the chips or sawdust from around the spindle and flanges. Fit the new blade, flanges and lock bolt.
PAGE 8
POW8002 EN 7.3 Calibrating the bevel angle gauge The angle gauges are set at the factory, but we recommend that for precision work you check and if necessary calibrating them as follows:  90°Bevel angle: Lock the upper arm in its lowered position by the release knob (18), and set bevel and mitre angles to 0°on the angle gauges. Place a protractor at the side of the saw blade and table, if the angle is not 90°bevel angle.
PAGE 9
POW8002 8.2 EN Fitting the work piece support Work-piece support retaining holes Locate the retaining rods into the retaining holes. Note: The retaining rod can be fitted to either or both sides of the saw depending on which type of cut and work-piece is being used. 9 CLEANING AND MAINTENANCE note: always ensure that the saw is turned off and the plug is removed from the mains supply before any repairs or maintenance are carried out. 9.
PAGE 10
POW8002 EN 10 TECHNICAL DATA Voltage – frequency Power rating No load speed Blade size Max cutting depth Bore size Number of teeth Max cutting capacity 0° x 90° 45° x 90° 0° x 45° 45° x 45° 230-240V – 50Hz 1400W 5000min-1 Ø 210mm 50mm Ø 25.4mm 24 120mm x 50mm 70mm x 50mm 110mm x 30mm 50mm x 30mm 11 NOISE Noise values measured according to relevant standard. (K = 3) Acoustic pressure level LpA 89 dB(A) Acoustic power level LwA 102 dB(A) Noise emission values measured according to relevant standard.
PAGE 11
POW8002    EN We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained. (Clean ventilation slots, carbon brushes serviced regularly, etc.). Your purchase receipt must be kept as proof of date of purchase. Your appliance must be returned undismantled to your dealer in an acceptably clean state, (in its original blow-moulded case if applicable to the unit), accompanied by proof of purchase.
PAGE 12
EN POW8002 14 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, Product: Mitre saw 1400W Trade mark: POWERplus Model: POW8002 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. Any unauthorized modification of the apparatus voids this declaration.