Operation Manual

ManualsBrandsPowerplus ManualsSawPOW8561

POW8561 EN

1 APPLICATION ................................................................................... 3

2 DESCRIPTION (FIG. A) ..................................................................... 3

3 PACKAGE CONTENT LIST .............................................................. 3

4 SYMBOLS .......................................................................................... 4

5 GENERAL POWER TOOL SAFETY WARNINGS ............................ 4

5.1 Working area ............................................................................................................. 4

5.2 Electrical safety ......................................................................................................... 4

5.3 Personal safety ......................................................................................................... 5

5.4 Power tool use and care ........................................................................................... 5

5.5 Service ....................................................................................................................... 6

6 SAFETY EQUIPMENT ....................................................................... 6

6.1 Cleaving wedge (Fig. 1) ............................................................................................ 6

6.2 Saw blade protector .................................................................................................. 6

6.3 Push stick (Fig. 2) ..................................................................................................... 6

7 UNPACKING AND ASSEMBLY ........................................................ 6

7.1 Assembly ................................................................................................................... 6

7.2 Fitting the parallel fence (Fig. 4) ............................................................................... 7

7.3 Mounting mitre angle stop (Fig. 5) ........................................................................... 7

7.4 Mounting the saw blade protector ........................................................................... 7

7.5 Mounting the extraction ............................................................................................ 8

8 OPERATION ...................................................................................... 8

8.1 Check before starting the device! ............................................................................ 8

8.2 Operating elements ................................................................................................... 8

8.2.1 On/off switch ............................................................................................................... 8

8.2.2 Overload Protection (15) ............................................................................................. 8

8.2.3 Setting mechanism for the tilt angle ............................................................................. 8

8.2.4 Hand crank for setting the cutting height ..................................................................... 8

8.3 Workpiece stops ....................................................................................................... 9

8.3.1 Mitre angle stop .......................................................................................................... 9

8.3.2 Mitre cuts (Fig. 6) ........................................................................................................ 9

8.3.3 Setting the stop rail of the parallel stop ........................................................................ 9

Summary of content (15 pages)

PAGE 1
POW8561 EN 1 APPLICATION ................................................................................... 3 2 DESCRIPTION (FIG. A) ..................................................................... 3 3 PACKAGE CONTENT LIST .............................................................. 3 4 SYMBOLS .......................................................................................... 4 5 GENERAL POWER TOOL SAFETY WARNINGS ............................ 4 5.1 Working area .................
PAGE 2
POW8561 EN 8.3.4 Parallel stop ................................................................................................................ 9 8.4 Setting the cutting height (Fig. 7) ............................................................................. 9 8.5 Setting the saw blade angle (Fig. 7) ....................................................................... 10 8.6 Sawing ..............................................................................................................
PAGE 3
EN POW8561 TABLE SAW 1800W POW8561 1 APPLICATION The device is designed to cleave and-cross-cut solid wood, laminated wood, chipboard, wood core plywood and similar wooden materials. Round pieces may not be sawed as the rotating saw blade may cause them to roll. Only those materials may be processed for which the particular saw blade is designed. Only saw blades suitable for the unit (carbide and chrome vanadium blades) may be used.
PAGE 4
EN POW8561 4 SYMBOLS The following symbols are used in this manual and/or on the machine: Denotes risk of personal injury or damage to the tool. Read manual before use. Conforms to essential safety standards of applicable European directives. Wear ear guards and goggles. Wear eye protection. Keep hands away from blades, Don’t touch the blades when starting or while operating the unit.
PAGE 5
POW8561    EN Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or tangled cords increase the risk of a lethal electric shock. When operating a power tool outdoors, use an extension cable suitable for outdoor use. Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.
PAGE 6
EN POW8561 5.5 Service  Your power tool should be serviced by a qualified specialist using only standard spare parts. This will ensure that it meets the required safety standards. 6 SAFETY EQUIPMENT 6.1 Cleaving wedge (Fig. 1) The cleaving wedge (7) prevents a workpiece being caught by the ascending teeth and being thrown against the operator. The cleaving wedge must remain in place during operation. 6.
PAGE 7
POW8561 EN 7.2 Fitting the parallel fence (Fig. 4) Insert the parallel fence (5) into the rail of the measuring scale. Check the setting at the window. Turn the knob to lock the parallel fence (5) into place. In order to obtain a perfectly parallel cut, you should check the gap between the fence and the saw blade at two positions using a meter rule. 7.3 Mounting mitre angle stop (Fig.
PAGE 8
EN POW8561 7.5 Mounting the extraction 6  Push one end of the extraction hose (11) onto the struts of the saw blade protector (6) and the other end onto one of the struts of the connection (13). Fix a suitable vacuum unit to the other strut of the connection (13).  13 8 OPERATION Risk of injury! In the event of a functional fault, immediately press the red button 0 on the On / Off switch and unplug. 8.
PAGE 9
EN POW8561 8.3 Workpiece stops 8.3.1 Mitre angle stop The stop can be adjusted by a maximum of 120mm for mitre cutting. Risk of injury! Do not push the stop (A) too far in the direction of the saw blade. The gap between the stop (A) and the saw blade should be approximately 2 cm. 8.3.2    Mitre cuts (Fig. 6) Push the mitre angle stop (9) into the required bar of the table surface. Loosen adjusting screw (A), set the required angle and then tighten the adjusting screw again.
PAGE 10
EN POW8561 8.5 Setting the saw blade angle (Fig. 7) Risk of injury! Parts of the body or objects located in the adjustment area may be caught by the operating saw blade! Only adjust the blade angle when the saw blade is at a standstill!   Unlock the saw blade angle adjustment (B) with the lever (C). Now the required cutting angle can be set by turning the hand wheel (B) via the scale. Retighten the locking lever (C) of the angle adjustment (B).
PAGE 11
EN POW8561 9 CLEANING AND MAINTENANCE 9.1 Cleaning and maintenance overview Prior to each use What? Check the saw blade to ensure it is correctly positioned and fixed in place. Check the saw blade protector box for wood chippings/saw dust Remove chippings if necessary. Check that the gap between the saw blade and the cleaving wedge is set to 3 to 8 mm; correct if necessary.
PAGE 12
EN POW8561 9.3.1 Fitting and changing the saw blade Caution! Unplug from power source. Caution! Ensure that the saw housing is well lit.     Remove the two screws of the table insert Remove the table insert Use the crank and turn to the left to bring the saw blade as far up as it will go. Use the wrenches (19-20) to undo the screws on the saw blade (Fig. 8) and exchange the blade with a suitable replacement. Watch the direction of operation! See the arrow on the saw blade.
PAGE 13
EN POW8561 11 TECHNICAL DATA Rated Voltage Rated Frequency Rated Power Weight Protection class Degree of protection Rotation speed Diameter of saw blade (external) Saw blade hole (internal) Saw blade thickness Number of teeth Max. cutting depth at 90° Max. cutting depth at 45° Table size Table height Dust extraction outlet 230-240 V 50 Hz 1800W 21.5 kg II IP20 4700 min-1 250 mm 30 mm 2.8 mm 36T 74 mm 63 mm 432 x 625 mm 865 mm Ø 36 mm 12 NOISE Noise values measured according to relevant standard.
PAGE 14
POW8561       EN Definitely excluded from the warranty is damage resulting from fluid permeation, excessive dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not following the instructions given in the manual), inexpert assembly, lightning strike, erroneus net voltage. This list is not exhaustive.
PAGE 15
EN POW8561 15 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, product: Table saw trade mark: PowerPlus model: POW8561 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. Any unauthorized modification of the apparatus voids this declaration.