Operation Manual

ManualsBrandsPowerplus ManualsSawPOWX07557T

POWX07557T EN

1 APPLICATION .................................................................................. 3

2 DESCRIPTION (FIG. A & B) ............................................................ 3

3 PACKAGE CONTENT LIST ............................................................. 3

4 SYMBOLS ........................................................................................ 4

5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4

5.1 Working area ........................................................................................................... 4

5.2 Electrical safety ....................................................................................................... 4

5.3 Personal safety ....................................................................................................... 4

5.4 Power tools use and care ....................................................................................... 5

5.5 Service ..................................................................................................................... 5

6 ADDITIONAL SAFETY INSTRUCTIONS ........................................ 5

7 ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS ................ 7

8 ASSEMBLY ...................................................................................... 7

8.1 Assembling the extension hoops .......................................................................... 7

8.2 Assembling the clamp ............................................................................................ 7

8.3 Assembling of the base frame (Fig 3) .................................................................... 7

9 OPERATING INSTRUCTIONS ........................................................ 8

9.1 Transporting the mitre saw .................................................................................... 8

9.2 Dust and chip extraction ........................................................................................ 8

9.3 Clamping the work piece ........................................................................................ 8

9.4 Horizontal mitre angle............................................................................................. 8

9.5 Adjusting of the cutting angle (Fig. 1) ................................................................... 8

9.6 Vertical bevel angle ................................................................................................. 8

9.7 Slide lock adjustment ............................................................................................. 9

9.8 Switching ON / OFF ................................................................................................. 9

9.9 Laser (13) ................................................................................................................. 9

9.10 Dust bag .................................................................................................................. 9

9.11 Sawing ..................................................................................................................... 9

9.12 Sawing special work pieces ................................................................................... 9

9.13 Replacing the saw blade (Fig. 2) ............................................................................ 9

10 CLEANING AND MAINTENANCE ................................................. 10

Summary of content (13 pages)

PAGE 1
POWX07557T EN 1 APPLICATION .................................................................................. 3 2 DESCRIPTION (FIG. A & B) ............................................................ 3 3 PACKAGE CONTENT LIST ............................................................. 3 4 SYMBOLS ........................................................................................ 4 5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 4 5.1 Working area .........................
PAGE 2
POWX07557T EN 10.1 Cleaning................................................................................................................. 10 10.2 Connecting cable .................................................................................................. 10 11 TECHNICAL DATA ........................................................................ 10 12 CUTTING CAPACITY..................................................................... 10 13 NOISE ......................................
PAGE 3
EN POWX07557T SLIDING MITRE SAW 2200W POWX07557T 1 APPLICATION This power tool is intended as a stationary machine for making straight and cross cuts in wood. You can saw hard and soft wood as well as chip and fibre boards. Only adults may use this tool. WARNING! For your own safety, read this manual and the general safety instructions carefully before using the appliance. Your power tool should only be given to other users together with these instructions. 2 DESCRIPTION (FIG. A & B) 1. 2. 3. 4. 5. 6. 7.
PAGE 4
POWX07557T EN 4 SYMBOLS The following symbols are used in this manual and/or on the machine: Denotes risk of personal injury or damage to the tool. Wear eye protection . Read manual before use. In accordance with essential requirements of the European directive(s) Wear gloves. Class II - The machine is double insulated; Earthing wire is therefore not necessary. 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions.
PAGE 5
POWX07557T       EN Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury. Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely.
PAGE 6
POWX07557T                       EN Only use correctly sharpened saw blades. Never exceed the maximum speed that is indicated on the saw blade. Before installing the saw blade, clean the axle, the flanges (especially the assembly surfaces) and the hexagonal nut. Incorrect mounting can lead to vibrations/knocking or slipping of the saw blade. Prevent that the saw comes into contact with metals, such as nails and screws.
PAGE 7
EN POWX07557T      Arsenic and chrome from chemically treated wood. The hazard to your health from such exposures is dependent on how frequently you do this kind of work. Measures for reducing your exposure to such chemicals: Always work in well-ventilated surroundings and with certified safety equipment, such as dust masks that have been specially designed for filtering out microscopic particles. For sawing operations, connect the equipment to a dust exhaust system.
PAGE 8
POWX07557T  EN Connect the four table legs (1) with the four upper (shortest) cross braces (2). For this, fix each cross brace from the inside with two screws (3) (incl. washers) and counternuts (4) to each table leg. And then attach the four lower (longer) lateral supports (5). Note: Only place the device on a level, skid-proof surface. The device must not wobble. 9 OPERATING INSTRUCTIONS 9.1 Transporting the mitre saw To transport the power tool, use the retaining pin (19).
PAGE 9
EN POWX07557T  Tighten the locking lever (22). 9.7 Slide lock adjustment  To unlock and lock the slide bar (14), turn the slide bar lock knob (23) counterclockwise or clockwise 9.8 Switching ON / OFF For your safety use both hands to switch the power tool on and off.    Connect the power tool to the power supply. Pull the on/off switch (16) in the direction of the handle. The saw blade rotates as long as you keep the switch engaged.
PAGE 10
EN POWX07557T        Pull the mitre saw downwards and lock it in the lowest position by pushing the retaining pin. Remove the front mounting screw from the protective hood Turn the centre cover and raise the blade guard. Press the spindle lock. Then remove the screw, outer flange and blade. Replace the saw blade (the tips of the sawing teeth have to point in the same direction as indicated by the arrow on the cover) and then resassemble all parts in the reverse order.
PAGE 11
EN POWX07557T 13 NOISE Noise emission values measured according to relevant standard. (K=3) Acoustic pressure level LpA 95 dB(A) Acoustic power level LwA 108 dB(A) ATTENTION! Wear over 85 dB(A). aw (Vibration) hearing protection 2,94 m/s² when sound pressure is K = 1,5 m/s² 14 STORAGE     Thoroughly clean the whole machine and its accessories. Store it out of the reach of children, in a stable and secure position, in a cool and dry place, avoid too high and too low temperatures.
PAGE 12
POWX07557T EN 16 WARRANTY               This product is warranted for a 36-month period effective from the date of purchase by the first user. This warranty covers all material or production flaws excluding : batteries, chargers, defective parts subject to normal wear & tear such as bearings, brushes, cables, and plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects resulting from maltreatment, accidents or alterations; nor the cost of transportation.
PAGE 13
EN POWX07557T 18 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, product: Sliding Mitre saw trade mark: POWERplus model: POWX07557T is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. Any unauthorized modification of the apparatus voids this declaration.