Operation Manual

ManualsBrandsPowerplus ManualsSawPOWX07582

POWX07582 EN

1 APPLICATION ................................................................................. 3

2 DESCRIPTION (FIG. A) .................................................................. 3

3 PACKAGE CONTENT LIST ............................................................ 3

4 SYMBOLS ....................................................................................... 4

5 GENERAL SAFETY WARNINGS ................................................... 4

5.1 Working area .......................................................................................................... 4

5.2 Electrical safety ...................................................................................................... 4

5.3 Personal safety ...................................................................................................... 4

5.4 Power tool use and care ........................................................................................ 5

5.5 Service .................................................................................................................... 5

6 ADDITIONAL SAFETY INSTRUCTIONS FOR CROSS-CUT AND

TABLE SAWS ................................................................................. 5

7 ELECTRICAL SAFETY ................................................................... 7

8 SPECIAL PRODUCT CHARACTERISTICS ................................... 7

9 INSTALLATION AND TRANSPORT .............................................. 7

9.1 Installation .............................................................................................................. 8

9.2 Transport ................................................................................................................ 8

9.2.1 Table saw operating mode ....................................................................................... 8

9.2.2 Cross-cut and mitre saw operating mode ................................................................. 8

9.2.3 Turntable ................................................................................................................. 9

9.2.4 Adjustment of the bevelling angle (Fig. 1)................................................................. 9

9.2.5 Mitre and width guide (Fig. 2) ................................................................................... 9

9.2.6 Connection to a dust collector .................................................................................. 9

9.2.7 Connection to AC power .......................................................................................... 9

10 OPERATIONS ............................................................................... 10

10.1 Cross-cut sawing mode ....................................................................................... 10

10.1.1 Safety instructions for the liftable saw blade guard (Fig. 3) ..................................... 10

10.1.2 Safety lock ............................................................................................................. 10

10.1.3 Installation.............................................................................................................. 10

10.1.4 Normal cross-cut operations .................................................................................. 11

10.1.5 Mitre sawing ........................................................................................................... 11

Summary of content (20 pages)

PAGE 1
POWX07582 EN 1 APPLICATION ................................................................................. 3 2 DESCRIPTION (FIG. A) .................................................................. 3 3 PACKAGE CONTENT LIST ............................................................ 3 4 SYMBOLS ....................................................................................... 4 5 GENERAL SAFETY WARNINGS ................................................... 4 5.1 Working area .............
PAGE 2
POWX07582 EN 10.1.6 Bevelling ................................................................................................................ 12 10.1.7 Sawing the workpiece: ........................................................................................... 12 10.1.8 Double mitre cut ..................................................................................................... 12 10.1.9 Sawing the workpiece: ...........................................................................
PAGE 3
EN POWX07582 CROSS-CUT AND MITRE SAW WITH TOP TABLE POWX07582 1 APPLICATION The machine is designed for sawing wood, metal and plastic. It is not designed for commercial use. WARNING! Read this manual and general safety instructions carefully before using the appliance, for your own safety. Your power tool should only be passed on together with these instructions. 2 DESCRIPTION (FIG. A) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
PAGE 4
POWX07582 EN 4 SYMBOLS In this manual and/or on the machine the following symbols are used: In accordance with essential Denotes risk of personal requirements of the European injury or damage to the tool. directive(s) Read manual before use "Class II - The machine is double insulated; Earthing wire is therefore not necessary Wear eye protection Wear gloves Do not touch a turning saw blade. 5 GENERAL SAFETY WARNINGS Read all safety warnings and instructions.
PAGE 5
EN POWX07582      Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely. Remove any adjusting keys or spanners before turning on the power tool. A spanner or key left attached to a rotating part of the power tool may result in personal injury. Do not reach out too far. Keep your feet firmly on the ground at all times.
PAGE 6
POWX07582                      EN Only use saw blades that are recommended by the manufacturer and that fulfil the EN8471 standard. Also make sure the riving knife is not thicker than the width of the saw cut, and that it is not thinner than the body of the saw blade. Always use the accessories that are recommended by this manual. Select the correct saw blade for the material must be sawn. To reduce the generation of noise, always make sure that the blade is sharp and clean.
PAGE 7
POWX07582              EN Do not carry out any free-hand operations. Free-hand means that you use your hands for supporting the workpiece, or for leading it with your hands, instead of using the rip fence or the mitre block. NEVER bend over or around the saw blade. NEVER reach for a workpiece, before the saw blade has come to a complete stop. Avoid a sudden or too quick infeed of a workpiece. Workpieces made of hard material should be fed in as slowly as possible.
PAGE 8
POWX07582 EN 9.1 Installation  Get help from another person for lifting the machine out of the box.  Turn the turntable into the 0° position and tighten up the mitre locks. Note: If the machine must be mounted on a workbench, then the rubber feet should NOT be installed. You run the risk of injury, if you handle the machine incorrectly when lifting or turning it. Always hold the machine firmly by the base (12).  Position the machine on a suitable surface:  All 4 feet must rest firmly on the surface.
PAGE 9
EN POWX07582 9.2.3 Turntable The turntable (11) can be turned 50° to the left and 60° to the right, and it can be fixed in preset positions of 0°, 15°, 22.5°, 30°, 45° and 60°. For turning the mitre table, the locking knob (9) must be released. To prevent that the mitre angle changes while sawing, the locking knob of the mitre saw must be tightened (also when the saw has been fixed at a preset stop). 9.2.4 Adjustment of the bevelling angle (Fig.
PAGE 10
POWX07582     EN  The mains voltage and the system frequency must conform to the voltage and frequency that is indicated on the technical data sheet of the machine;  Fusing protection with a residual current device (RCD), with a sensitivity of 30 mA.  Sockets must be properly installed, earthed and tested. Position a power cable in such a way that it does not hinder the work and cannot be damaged. Protect the power cable against heat, aggressive fluids and sharp edges.
PAGE 11
POWX07582 EN HAZARD!         Before using the machine, always check that the following items function properly.  Liftable saw blade guard.
PAGE 12
POWX07582     EN Lower the saw head carefully and completely downwards while holding firmly onto the handgrip. You should only apply medium pressure while sawing, so as to prevent that the speed of the motor slows down. Saw the workpiece in one single movement. Carefully let the saw head return to its topmost starting position. The saw should be switched off by releasing the switch (20), if no further sawing has to be done. Note: The mitre saw is activated at certain angles, such as at 0°, 15°, 22.
PAGE 13
POWX07582      EN Push on the upper half of the ON/OFF switch and push on the safety lock. Lower the saw head carefully and completely downwards, while firmly holding onto the handgrip. You should only apply minimum pressure while sawing, so as to prevent the motor from slowing down. Saw the workpiece in one single movement. Carefully let the saw head return to its topmost starting position. If further sawing works do not have to be carried out immediately, switch the saw OFF. 10.2 10.2.
PAGE 14
EN POWX07582      Before starting to work, check that the following items are in a proper condition.
PAGE 15
POWX07582 EN 11.2 Maintenance  Our machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning. 11.2.1 For all maintenance works Switch the machine “OFF” Remove the plug from the socket Wait until the machine has come to a complete standstill Repair and maintenance works may only be carried out by trained specialists, with the exception of those described in this chapter.
PAGE 16
POWX07582 11.2.5 EN Changing the saw blade (Fig. 5) HAZARD!The saw blade may be extremely hot and can cause burns, immediately after you have stopped sawing. Always led a hot saw blade cool off. Never clean saw blades with flammable liquids. This can cause injuries, also when the saw blade is not turning. The movable saw blade guard must cover the saw blade, whenever you tighten or release the driveshaft bolt (E1). Always wear gloves while changing the saw blade.
PAGE 17
POWX07582 EN  Saw blades made of high-speed steel (HSS)  Damaged saw blades  Saw blades with missing teeth HAZARD!  Only use OEM components for installing the saw blade.  Do not use loose reduction rings; the saw blade could come loose.  Saw blades must be mounted in such a way that they cannot wobble, and that they cannot come loose during operations.  Install the outer saw flange (E2).  The two flanges must fit over the surfaces of the saw shaft.
PAGE 18
EN POWX07582     Loosen the left-hand/right-hand screw (N1). Adapt the support arm until the saw blade is located precisely at an angle of 90°/45° in relation to the turntable. Retighten the left-hand/right-hand screw (N1). After loosening the screw (N4), adapt the position of the indicator (N3) until the value that is indicated corresponds to the currently preset stop position of the support arm. 11.3.4 Adapting the sawing depth stop (Fig.
PAGE 19
EN POWX07582 Insulation class Weight gross/net II 24 kg / 19 kg 13 NOISE Noise values measured according to relevant standard. (K=3) Acoustic pressure level LpA 93 dB(A) Acoustic power level LwA 106 dB(A) ATTENTION! Wear hearing protection when sound pressure is over 85 dB(A).
PAGE 20
EN POWX07582 15 ENVIRONMENT Should your appliance need replacement after extended use, do not discard it with the household rubbish but dispose of it in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist. Check with your Local Authority or retailer for recycling advice. 16 DECLARATION OF CONFORMITY VARO N.V.