Operation Manual

ManualsBrandsPowerplus ManualsSawPOWX0760

POWX0760 EN

1 APPLICATION .................................................................................. 4

2 DESCRIPTION ................................................................................. 4

3 PACKAGE CONTENT LIST ............................................................. 5

4 SYMBOLS ........................................................................................ 5

5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 6

5.1 Work area ................................................................................................................ 6

5.2 Electrical safety ....................................................................................................... 6

5.3 Personal safety ....................................................................................................... 6

5.4 Power tool use and care ......................................................................................... 7

5.5 Service ..................................................................................................................... 7

6 ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS ....... 7

6.1 For both Mitre saw mode and table saw (bench saw) mode: ............................... 7

6.2 When using in Mitre saw mode: ............................................................................. 8

6.3 When using in the table saw (bench saw) mode: .................................................. 8

7 INSTALLATION ................................................................................ 9

7.1 Bench mounting (Fig. 1 & 3) ................................................................................... 9

7.1.1 For the fully-extended feet set up as the high table. .................................................. 9

7.1.2 For the folded feet set up as the low table ................................................................. 9

8 FUNCTIONAL DESCRIPTION ......................................................... 9

8.1 Blade guard (Fig. 4, 5 & 6) ...................................................................................... 9

8.2 Maintaining maximum cutting capacity (Fig. 7) .................................................. 10

8.3 Adjusting the Mitre angle (Fig. 9 & 10) ................................................................. 11

8.4 Adjusting the bevel angle (Fig. 11 & 12) .............................................................. 11

8.4.1 In the Mitre saw mode ............................................................................................. 11

8.4.2 In the table saw mode (Fig. 13) ............................................................................... 11

8.5 Switch action (Fig. 14) .......................................................................................... 11

8.5.1 Switch for the table saw mode (B) ........................................................................... 11

8.6 Adjusting the depth of cut (Fig. 15 - 21) .............................................................. 11

9 ASSEMBLY .................................................................................... 11

9.1 Socket wrench storage (Fig. 17)........................................................................... 11

9.2 Table height two-way set up ................................................................................. 12

Summary of content (23 pages)

PAGE 1
POWX0760 EN 1 APPLICATION .................................................................................. 4 2 DESCRIPTION ................................................................................. 4 3 PACKAGE CONTENT LIST ............................................................. 5 4 SYMBOLS ........................................................................................ 5 5 GENERAL POWER TOOL SAFETY WARNINGS .......................... 6 5.1 Work area ......................
PAGE 2
POWX0760 EN 9.2.1 High table set up (Fig. 18) ....................................................................................... 12 9.2.2 Low table set up (Fig. 19) ........................................................................................ 12 9.3 Installing or removing saw blade ......................................................................... 12 9.4 Adjusting riving knife (fig 25,26 & 27) .................................................................. 12 9.
PAGE 3
POWX0760 EN 10.2.1 Work helpers ...................................................................................................... 18 10.2.2 Push block (Fig. 57) ........................................................................................... 18 10.2.3 Auxiliary fence (Fig. 58) ...................................................................................... 18 10.2.4 Ripping.........................................................................................................
PAGE 4
POWX0760 EN FLIP OVER SAW 1800W POWX0760 1 APPLICATION The tool is intended for accurate straight and Mitre cutting in wood. The tool can be used both in Mitre saw mode and in table saw mode by turning over the table around its axis. Het apparaat is niet voor industrieel gebruik bestemd. WARNING! Read this manual and general safety instructions carefully before using the appliance, for your own safety. Your power tool should only be passed on together with these instructions. 2 DESCRIPTION 1. 2. 3. 4. 5.
PAGE 5
EN POWX0760 3 PACKAGE CONTENT LIST      Remove all packing materials Remove remaining packaging and transit supports (if existing) Check the completeness of the packing content Check the appliance, the power cord, the power plug and all accessories for transportation damages. Keep the packaging materials as far as possible till the end of the warranty period. Dispose it into your local waste disposal system afterwards.
PAGE 6
EN POWX0760 Wear a mask In dusty conditions Wear eye protection 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions. Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains operated (corded) power tool or battery operated (cordless) power tool. 5.1 Work area  Keep work area clean and well lit.
PAGE 7
EN POWX0760  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards. 5.4 Power tool use and care  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.  Do not use the power tool if the switch does not turn it on and off.
PAGE 8
POWX0760 EN     Select the correct saw blade for the material to be cut. Do not use saw blades manufactured from high speed steel. To reduce the emitted noise, always be sure that the blade is sharp and clean. Use correctly sharpened saw blades. Observe the maximum speed marked on the saw blade.  Do not cut metals such as nails and screws. Inspect for and remove all nails, screws and other foreign matter from the workpiece before operation.
PAGE 9
POWX0760         EN Make sure that the turn table is fixed securely. Make sure that the arm is securely fixed in the working position. Tighten the lever clockwise to fix the arm. Use (6) push stick or (6) push block to avoid working with the hands and fingers close to the saw blade. Make sure the blade is not contacting the riving knife or workpiece before the switch is turned on. Always store the push-stick when it is not in use.
PAGE 10
POWX0760 EN guards are spring loaded so it returns to its original position when the cut is completed and the handle is raised. The top blade guard falls flat on the table surface after workpiece has passed under it. NEVER DEFEAT OR REMOVE THE LOWER BLADE GUARDS, THE SPRING WHICH ATTACHES TO THE LOWER BLADE GUARD, OR THE TOP BLADE GUARD except for the note below. In the interest of your personal safety, always maintain each blade guard in good condition.
PAGE 11
EN POWX0760 8.3 Adjusting the Mitre angle (Fig. 9 & 10) Loosen the clamping screw on the guide fence by turning counterclockwise. Turn the turn table by handle. When you have moved the handle to the position where the pointer points to the desired angle on the Mitre scale, securely tighten the clamping screw clockwise. CAUTION:  When turning the turn table, be sure to raise the handle fully.  After changing the Mitre angle, always secure the turn table by tightening the clamping screw firmly. 8.4 8.4.
PAGE 12
POWX0760 EN 9.2 Table height two-way set up The table height can be set up in two ways, high or low table. WARNING: Before falling down the tool backwards, always set the tool in the Mitre saw mode and lock the tool head in the lowest position. 9.2.1 High table set up (Fig. 18) To set up the tool with high table, proceed as follows.  Fall down the tool carefully BACKWARDS without fail while holding it with both hands.  Fix the 4 legs using a bolt, wing nut and the U-shaped customized washer. 9.2.
PAGE 13
POWX0760 EN The riving knife has been installed before shipment from the factory so that the blade and riving knife are in a straight line after your simple set-up. Refer to the section titled “Repositioning riving knife” for the set-up. CAUTION:  If the blade and riving knife are not aligned properly, a dangerous pinching condition may result during operation. Make sure the riving knife is positioned between both outer ends of the blade teeth when viewing from the top.
PAGE 14
POWX0760     EN Be sure to adjust the rip fence so that it is parallel with the blade, or a dangerous kickback condition may occur. Be sure to adjust the rip fence so that it does not contact the top blade guard or saw blade. (Fig. 34) Do not relocate or carry the tool by rip fence. Raising the installed rip fence or exerting a force on it to the right and left with your hand grabbing its top end may damage it and impair its function. 9.6 Installing and adjusting Mitre gauge (Fig.
PAGE 15
EN POWX0760 The tool is shipped from the factory with the set-up in Mitre saw mode. Before use in table saw mode, change the set up and follow the procedure below. 9.9.1 Securing the turn table (Fig. 41) To secure the turn table, tighten the screw firmly on the guide fence at 0° Mitre angle. 9.9.2 Securing the tool head (Fig. 42) Secure the tool head by tightening the lever in the direction of arrow shown in the figure. 9.9.3 Releasing the lower limit stopper (Fig.
PAGE 16
POWX0760 EN CAUTION:  After installing the top blade guard, make sure that it works smoothly. 9.10 Setting up the tool in Mitre saw mode (Fig. 50) WARNING: Be sure to install the lower blade guard C before using the tool in Mitre saw mode. To change the set up from table saw mode to Mitre saw mode, reverse the procedure of the section titled “Setting up the tool in table saw mode”. 9.10.
PAGE 17
POWX0760 EN 10 OPERATION CAUTION:  Before use, be sure to release the handle from the lowered position by pulling the stopper pin and turning it to the angle of 90°.  Make sure the blade is not contacting the workpiece, etc. before the switch is turned on. 10.1 Cutting as mitre saw WARNING: Make sure that the lower blade guard C is installed before using in Mitre saw mode. CAUTION:  Do not apply excessive pressure on the handle when cutting.
PAGE 18
POWX0760 10.1.4 EN Compound cutting Compound cutting is the process in which a bevel angle is made at the same time in which a Mitre angle is being cut on a workpiece. Compound cutting can be performed at angle shown in the table. Bevel angle Miter angle 45° Left and Right 0 – 45° When performing compound cutting, refer to “Press cutting”, “Mitre cutting” and “Bevel cut” explanations. 10.1.5 Cutting aluminum extrusion (Fig.
PAGE 19
POWX0760 10.2.4 EN Ripping CAUTION:  When ripping, remove the Mitre gauge from the table.  When cutting long or large workpieces, always provide adequate support behind the table. DO NOT allow a long board to move or shift on the table. This will cause the blade to bind and increase the possibility of kickback and personal injury. The support should be at the same height as the table. 1. Adjust the depth of cut a bit higher than the thickness of the workpiece.
PAGE 20
POWX0760 10.2.9 EN Carrying tool (Fig. 66) Make sure that the tool is unplugged. For the tool just used in the Mitre saw mode, secure the blade at 0° bevel angle and the turn table at 0° Mitre angle. Lower the handle fully and lock it in the lowered position by fully pushing in the stopper pin. Carry the tool by holding the tool part shown in the figure. (Fig. 67) CAUTION:  Always secure all moving portions before carrying the tool.
PAGE 21
POWX0760 EN 11.2 Replacing carbon brushes (Fig. 73 & 74) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 11.
PAGE 22
EN POWX0760 13 NOISE Noise emission values measured according to relevant standard. (K=3) Acoustic pressure level LpA 92 dB(A) Acoustic power level LwA 105 dB(A) ATTENTION! Wear over 85 dB(A). aw (Vibration) hearing protection 1.73 m/s² when sound pressure is K = 1.5 m/s² 14 STORAGE     Thoroughly clean the whole machine and its accessories. Store it out of the reach of children, in a stable and secure position, in a cool and dry place, avoid too high and too low temperatures.
PAGE 23
EN POWX0760 16 ENVIRONMENT Should your appliance need replacement after extended use, do not discard it with the household rubbish but dispose of it in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycle facilities exist. Check with your Local Authority or retailer for recycling advice. 17 DECLARATION OF CONFORMITY VARO N.V.