User Manual

ManualsBrandsPowerplus ManualsPower sawsPOWX0761 FLIPOVER 1400W 216MM EN

POWX0761 EN

1 APPLICATION ................................................................................ 4

2 DESCRIPTION ................................................................................ 4

3 PACKAGE CONTENT LIST ............................................................ 5

4 SYMBOLS ....................................................................................... 5

5 GENERAL POWER TOOL SAFETY WARNINGS ......................... 6

5.1 Work area ............................................................................................................... 6

5.2 Electrical safety ..................................................................................................... 6

5.3 Personal safety ...................................................................................................... 6

5.4 Power tool use and care ........................................................................................ 7

5.5 Service .................................................................................................................... 7

6 ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS ...... 7

6.1 For both Mitre saw mode and table saw (bench saw) mode: .............................. 7

6.2 When using in Mitre saw mode: ............................................................................ 8

6.3 When using in the table saw (bench saw) mode: ................................................ 9

7 INSTALLATION .............................................................................. 9

7.1 Bench mounting (Fig. 1 & 3) ................................................................................. 9

7.1.1 For the fully-extended feet set up as the high table. ................................................. 9

7.1.2 For the folded feet set up as the low table ................................................................ 9

8 FUNCTIONAL DESCRIPTION ...................................................... 10

8.1 Blade guard (Fig. 4, 5 & 6) ................................................................................... 10

8.2 Maintaining maximum cutting capacity (Fig. 7) ................................................. 11

8.3 Adjusting the Mitre angle (Fig. 9 & 10) ............................................................... 11

8.4 Adjusting the bevel angle (Fig. 11 & 12) ............................................................. 11

8.4.1 In the Mitre saw mode............................................................................................ 11

8.4.2 In the table saw mode (Fig. 13) .............................................................................. 11

8.5 Switch action (Fig. 14) ......................................................................................... 12

8.5.1 Switch for the Mitre saw mode (A) ......................................................................... 12

8.5.2 Switch for the table saw mode (B) .......................................................................... 12

8.6 Adjusting the depth of cut (Fig. 15 - 21) ............................................................. 12

9 ASSEMBLY ................................................................................... 12

9.1 Socket wrench storage (Fig. 17) ......................................................................... 12

Summary of content (24 pages)

PAGE 1
POWX0761 EN 1 APPLICATION ................................................................................ 4 2 DESCRIPTION ................................................................................ 4 3 PACKAGE CONTENT LIST............................................................ 5 4 SYMBOLS ....................................................................................... 5 5 GENERAL POWER TOOL SAFETY WARNINGS ......................... 6 5.1 Work area .............................
PAGE 2
POWX0761 EN 9.2 Table height two-way set up ............................................................................... 12 9.2.1 High table set up (Fig. 18) ...................................................................................... 12 9.2.2 Low table set up (Fig. 19) ...................................................................................... 13 9.3 Installing or removing saw blade ........................................................................ 13 9.
PAGE 3
POWX0761 EN 10.2 Cutting as table saw (bench mode) .................................................................... 19 10.2.1 Work helpers ......................................................................................................... 19 10.2.2 Push block (Fig. 57) ............................................................................................... 19 10.2.3 Auxiliary fence (Fig. 58) .........................................................................................
PAGE 4
POWX0761 EN FLIP OVER SAW 1400W POWX0761 1 APPLICATION The tool is intended for accurate straight and Mitre cutting in wood. The tool can be used both in Mitre saw mode and in table saw mode by turning over the table around its axis. It is not designed for commercial use. WARNING! Read this manual and general safety instructions carefully before using the appliance, for your own safety. Your power tool should only be passed on together with these instructions. 2 DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9.
PAGE 5
EN POWX0761 3 PACKAGE CONTENT LIST     Remove all packing materials Remove remaining packaging and transit supports (if existing) Check the completeness of the packing content Check the appliance, the power cord, the power plug and all accessories for transportation damages.  Keep the packaging materials as far as possible till the end of the warranty period. Dispose it into your local waste disposal system afterwards.
PAGE 6
POWX0761 EN 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions. Failure to follow all warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains operated (corded) power tool or battery operated (cordless) power tool. 5.1 Work area  Keep work area clean and well lit. Cluttered and dark areas invite accidents.
PAGE 7
EN POWX0761  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards. 5.4 Power tool use and care  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.  Do not use the power tool if the switch does not turn it on and off.
PAGE 8
POWX0761 EN     Select the correct saw blade for the material to be cut. Do not use saw blades manufactured from high speed steel. To reduce the emitted noise, always be sure that the blade is sharp and clean. Use correctly sharpened saw blades. Observe the maximum speed marked on the saw blade.  Do not cut metals such as nails and screws. Inspect for and remove all nails, screws and other foreign matter from the workpiece before operation.
PAGE 9
POWX0761 EN 6.3 When using in the table saw (bench saw) mode:  Do not perform any operation freehand. Freehand means using your hands to support or guide the workpiece, in lieu of (6) rip fence.  Make sure that the turn table is fixed securely.  Make sure that the arm is securely fixed in the working position. Tighten the lever clockwise to fix the arm.  Use (6) push stick or (6) push block to avoid working with the hands and fingers close to the saw blade.
PAGE 10
POWX0761 EN 8 FUNCTIONAL DESCRIPTION CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 8.1 Blade guard (Fig. 4, 5 & 6) Caution:  Make sure that the handle cannot be lowered without pushing the lever nearby the handle to the left. (fig 2 - 20)  Make sure that the lower blade guards A dose not open unless the lever near the handle is pushed at the topmost position of the handle.
PAGE 11
POWX0761 EN 8.2 Maintaining maximum cutting capacity (Fig. 7) This tool is factory adjusted to provide the maximum cutting capacity for a 255 mm saw blade. When installing a new blade, always check the lower limit position of the blade and if necessary, adjust it as follows: CAUTION: When making this adjustment, unplug the tool. First, unplug the tool. Lower the handle completely.
PAGE 12
EN POWX0761 8.5 8.5.1 Switch action (Fig. 14) Switch for the Mitre saw mode (A) CAUTION:  Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released.  When not using the tool, remove the lock-off button and store it in a secure place. This prevents unauthorized operation.  Do not pull the switch lever hard without pressing in the lock-off button. This can cause switch breakage.
PAGE 13
POWX0761 9.2.2 EN Low table set up (Fig. 19)  Fold in the 4 legs. To do so :  Fall down the tool carefully BACKWARDS without fail while holding it with both hands.  untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with tabel. Then tigthen the wing nut again  Return the tool to the upright position. 9.3 Installing or removing saw blade CAUTION:  Always be sure that the tool is switched off and unplugged before installing or removing the blade.
PAGE 14
POWX0761 EN 9.5 Installing and adjusting rip fence (Fig. 28)  Install the rip fence on the table so that the rip fence holder engages with the guide rail. Tighten the clamping screw (48) of the rip fence firmly clockwise.  Loosen the clamping screw (47)  Slide the rip fence and secure it so that the far end from you of the rip fence is aligned with the point at which the front edge of saw blade just appears from top surface of the workpiece.
PAGE 15
EN POWX0761 9.6 Installing and adjusting Mitre gauge (Fig. 35) Install the Mitre gauge by inserting its shaft into one of two grooves in the table from the front. Mitre gauge fence that is also used as rip fence can be installed on the Mitre gauge according to your work. 9.7 Dust bag (Fig 36, 37 & 38) The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit it onto the dust nozzle.
PAGE 16
EN POWX0761 9.9.2 Securing the tool head (Fig. 42) Secure the tool head by tightening the lever in the direction of arrow shown in the figure. 9.9.3 Releasing the lower limit stopper (Fig. 43) Make sure that the end of the lower limit stopper is at the A position in the figure. Turn the end of the lower limit stopper counterclockwise to the A position when it is positioned at the B position. 9.9.4 Repositioning the riving knife (Fig. 44) The position (Fig. 44-A) should be changed as follows.
PAGE 17
POWX0761 9.10 EN Setting up the tool in Mitre saw mode (Fig. 50) WARNING: Be sure to install the lower blade guard C before using the tool in Mitre saw mode. To change the set up from table saw mode to Mitre saw mode, reverse the procedure of the section titled “Setting up the tool in table saw mode”. 9.10.1 Removing the top blade guard Push the push button of the top blade guard to its side surface and then just take away the top blade guard upward with the button depressed. 9.10.
PAGE 18
POWX0761 EN 10 OPERATION CAUTION:  Before use, be sure to release the handle from the lowered position by pulling the stopper pin and turning it to the angle of 90°.  Make sure the blade is not contacting the workpiece, etc. before the switch is turned on. 10.1 Cutting as mitre saw WARNING: Make sure that the lower blade guard C is installed before using in Mitre saw mode. CAUTION:  Do not apply excessive pressure on the handle when cutting.
PAGE 19
POWX0761 10.1.4 EN Compound cutting Compound cutting is the process in which a bevel angle is made at the same time in which a Mitre angle is being cut on a workpiece. Compound cutting can be performed at angle shown in the table. Bevel angle Miter angle 45° Left and Right 0 – 45° When performing compound cutting, refer to “Press cutting”, “Mitre cutting” and “Bevel cut” explanations. 10.1.5 Cutting aluminum extrusion (Fig.
PAGE 20
POWX0761 10.2.4 EN Ripping CAUTION:  When ripping, remove the Mitre gauge from the table.  When cutting long or large workpieces, always provide adequate support behind the table. DO NOT allow a long board to move or shift on the table. This will cause the blade to bind and increase the possibility of kickback and personal injury. The support should be at the same height as the table. 1. Adjust the depth of cut a bit higher than the thickness of the workpiece.
PAGE 21
POWX0761 10.2.9 EN Carrying tool (Fig. 66) Make sure that the tool is unplugged. For the tool just used in the Mitre saw mode, secure the blade at 0° bevel angle and the turn table at 0° Mitre angle. Lower the handle fully and lock it in the lowered position by fully pushing in the stopper pin. Carry the tool by holding the tool part shown in the figure. (Fig. 67) CAUTION:  Always secure all moving portions before carrying the tool.
PAGE 22
POWX0761 EN 11.2 Replacing carbon brushes (Fig. 73 & 74) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 11.
PAGE 23
POWX0761 EN 13 NOISE EMISSION VALUES The noise and weighted root mean square acceleration value are measured in accordance with EN 61029 LpA (sound pressure) 92.6 dB(A) LwA (Sound power level ) 105.6 dB(A) The machine may exceed 85 dB(A) at the workplace In this case, noise protection measures need to be introduced to protect the user Vibration (aw) 1.729 m/s² Wear suitable eye, respiration, hand & hearing protection when working 14 STORAGE  Thoroughly clean the whole machine and its accessories.
PAGE 24
EN POWX0761 17 DECLARATION OF CONFORMITY VARO N.V. - Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, product : Flip over saw 1400W trade mark : POWERplus model : POWX0761 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards. Any unauthorized modification of the apparatus voids this declaration.