Operation Manual

ManualsBrandsPowerplus ManualsChainsawPOWXG1018

POWXG1018 EN

1 APPLIANCE ....................................................................................... 3

2 DESCRIPTION ................................................................................... 3

3 PACKAGE CONTENT LIST .............................................................. 4

4 SYMBOLS .......................................................................................... 4

5 SAFETY.............................................................................................. 4

6 KICKBACK SAFETY PRECAUTIONS .............................................. 6

7 SAFETY WARNINGS GASOLINE .................................................... 7

8 ASSEMBLY ........................................................................................ 7

8.1 Tools for assembly ................................................................................................... 7

8.2 Assembly requirements ............................................................................................ 7

8.3 Guide bar / saw chain / clutch cover installation .................................................... 7

8.3.1 To install saw chain: .................................................................................................... 8

8.3.2 Saw chain tension adjustment ..................................................................................... 8

8.3.3 To adjust saw chain: ................................................................................................... 8

8.3.4 Chain brake mechanical test ....................................................................................... 9

8.3.5 To test chain brake: ..................................................................................................... 9

9 FUEL AND LUBRICATION................................................................ 9

9.1 Fuel ............................................................................................................................ 9

9.2 Mixing fuel ............................................................................................................... 10

9.2.1 Fuel and lubrication symbols ..................................................................................... 10

9.2.2 Fuel mixing table ....................................................................................................... 10

9.2.3 Recommended fuels ................................................................................................. 10

9.2.4 Chain and bar lubrication .......................................................................................... 10

10 OPERATION .................................................................................... 10

10.1 Engine pre start checks .......................................................................................... 10

10.2 To start engine ........................................................................................................ 10

10.3 Re-starting a warm engine...................................................................................... 11

10.4 To stop engine ........................................................................................................ 11

10.5 Chain brake operational test .................................................................................. 11

10.6 Saw chain / bar lubrication ..................................................................................... 11

Summary of content (22 pages)

PAGE 1
POWXG1018 EN 1 APPLIANCE ....................................................................................... 3 2 DESCRIPTION ................................................................................... 3 3 PACKAGE CONTENT LIST .............................................................. 4 4 SYMBOLS .......................................................................................... 4 5 SAFETY.......................................................................................
PAGE 2
POWXG1018 EN 10.7 Automatic oiler ........................................................................................................ 12 10.8 General cutting instructions................................................................................... 12 10.8.1 Felling ....................................................................................................................... 12 10.8.2 Limbing ...........................................................................................
PAGE 3
POWXG1018 EN CHAINSAW 49.3CC POWXG1018 1 APPLIANCE These models are intended for infrequent use by homeowners, cottagers, and campers, and for such general applications as clearing, pruning, cutting firewood, etc. They are not intended for prolonged use. If the intended use involves prolonged periods of operation, this may cause circulatory problems in the user’s hands due to vibration. It is not designed for commercial use. 2 DESCRIPTION 1. Saw chain 11. Fuel tank cap 2. Guide bar 12. Starter cover 3.
PAGE 4
EN POWXG1018 3 PACKAGE CONTENT LIST      Remove all packaging materials. Remove remaining packing and package inserts (if included). Check that the package contents are complete. Check the appliance, the power cord, the power plug and all accessories for transportation damage. Keep the packing materials as far as possible till the end of the warranty period. Dispose it into your local waste disposal system afterwards.
PAGE 5
POWXG1018                         EN Use caution when handling fuel. To avoide fire, move the chain saw at least 10 feet (3m) from the fueling point before starting the engine. DO NOT allow other persons to be near when starting or cutting with the chain saw. Keep bystanders and animals out of the work area. DO NOT start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree.
PAGE 6
EN POWXG1018 6 KICKBACK SAFETY PRECAUTIONS KICKBACK may occur when the NOSE or TIP of the guide bar touches an object, or when wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse reaction, kicking the guide bar up and back toward the operator. PINCHING the saw chain along the BOTTOM of the guide bar may PULL the saw forward away from the operator.
PAGE 7
EN POWXG1018 7 SAFETY WARNINGS GASOLINE WARNING: Use extra care in handling fuels. They are flammable and the vapours are explosive. The following points must be observed.         Use only an approved container. Never remove the fuel cap or add fuel with the power source running. Allow engine exhaust components to cool before refuelling. Do not smoke. Never refuel the machine indoors. Never store the machine or fuel containers inside, where is an open flame, such as a water heater.
PAGE 8
EN POWXG1018  Place the slotted end of the guide bar over the bar bolt (F). Slide guide bar behind clutch drum (G) until the guide bar stops (fig. 3d. 8.3.1 To install saw chain: Always wear heavy duty gloves when handling saw chain or making saw chain adjustments.  Spread chain out in a loop with cutting edges (A) pointing clockwise around loop (fig. 4a).  Slip the chain around the sprocket (B) behind the clutch (C). Make sure the links fit between the sprocket teeth (fig. 4b).
PAGE 9
EN POWXG1018 Caution: a new saw chain stretches, requiring adjustment after as few as 5 cuts. This is normal with a new chain, and the interval between future adjustments will lengthen quickly. Caution: if saw chain is too loose or too tight, the sprocket, bar, chain, and crankshaft bearings will wear more rapidly. Study fig.6 for information concerning correct cold tension (A), correct warm tension (B), and as a guide for when saw chain needs adjustment (C). 8.3.
PAGE 10
EN POWXG1018 9.2 Mixing fuel Add oil to an approved fuel container followed by the gasoline to allow incoming gasoline to mix with oil. Shake container to ensure thorough mix. Warning: Lack of lubrication voids engine warranty. Gasoline and oil must be mixed at 25:1 9.2.1 Fuel and lubrication symbols 9.2.2 Fuel mixing table Gasoline liters 2-cycle oil ml 9.2.
PAGE 11
EN POWXG1018     Place the saw on a firm and level surface. Hold the saw securely with your foot as illustrated. Tug sharply on the starter 2 times. Watch the chain in case it runs. (Fig. 9d) When engine turns, choke will automatically switch off. (Fig. 9e) Let the engine run for 10 seconds to warm up. Press the trigger (H) and put it into idle. (Fig. 9f) If the engine does not start up, repeat the above steps. 10.3 Re-starting a warm engine  Make sure the on/off switch is in the “I” position.
PAGE 12
EN POWXG1018 Note: saw chain stretches during use, particularly when it is new, and it will occasionally be necessary to adjust and tighten it. New chain will require adjustment after about 5 minutes of operation. 10.7 Automatic oiler Your chain saw is equipped with an automatic clutch driven oiler system. The oiler automatically delivers the proper amount of oil to the bar and chain. As the engine speed increases, so does the oil flow to the bar pad.
PAGE 13
EN POWXG1018 WARNING: Never walk in front of a tree that has been notched. Make the felling cut (D) from the other side of the tree and 1.5 - 2.0 inches (3-5 cm) above the edge of the notch (C) (Fig. 11b) Never saw completely through the trunk. Always leave a hinge. The hinge guides the tree. If the trunk is completely cut through, control over the felling direction is lost. Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to move.
PAGE 14
EN POWXG1018  Log supported on both ends: First, overbuck 1/3 diameter of log to avoid splintering. Second, underbuck to meet first cut and avoid pinching (Fig. 13c) NOTE: The best way to hold a log while bucking is to use a sawhorse. When this is not possible, the log should be raised and supported by the limb stumps or by using supporting logs. Be sure the log being cut is securely supported. 10.8.
PAGE 15
EN POWXG1018 11.3 Air filter Caution: never operate saw without the air filter. Dust and dirt will be drawn into engine and damage it. Keep the air filter clean! To clean air filter:  Remove knob (A) holding air filter cover in place, remove the top cover (B) by loosening the cover retaining screw. Cover will lift off. (fig. 15a)  Lift the air filter (C) out of air-box (D) (fig. 15b).  Clean air filter. Wash filter in clean, warm, soapy water. Rinse in clear, cool water. Air dry completely.
PAGE 16
EN POWXG1018 11.6 Spark plug Note: for efficient operation of saw engine, spark plug must be kept clean and properly gapped.        Push stop switch down. Remove knob (A) holding air filter cover in place, remove the top cover (B) by loosening the cover retaining screw. Cover will lift off. (fig. 18a) Disconnect the wire connector (C) from the spark plug (D) by pulling and twisting at the same time (fig. 18b). Remove spark plug with spark plug socket wrench.
PAGE 17
EN POWXG1018 To lubricate sprocket tip: Warning: wear heavy duty work gloves when handling the bar and chain.  Press the stop switch down. Note: it is not necessary to remove the saw chain to lubricate the guide bar sprocket tip. Lubrication can be done on the job. 21. Clean the guide bar sprocket tip.  Using the lube gun (optional), insert needle nose into the lubrication hole and inject grease until it appears at outside edge of sprocket tip (fig. 20).  Rotate saw chain by hand.
PAGE 18
EN POWXG1018  To sharpen the chain basically, make 2 to 3 pulls of the file from the inside out. Warning: after 3 to 4 of your sharpening of the cutting teeth, havve the saw chain sharpened in any authorised service. They will sharpen the depth limiter as well, which provides the distance. Chain sharpening The pitch of the chain (fig. 21) depends on the model. POWXG1018 Pitch 0.325” Gauge 0.058” Sharpen the chain using protective gloves and a round file of ø5/32” (4mm).
PAGE 19
POWXG1018 EN Breaking in a new saw chain: A new chain and bar will need chain readjustment after as few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will begin to lengthen quickly. Warning: never have more than 3 links removed from a loop of chain. This could cause damage to the sprocket. Chain lubrication: Always make sure the automatic oiler system is working properly. Keep the oil tank filled with good quality chain, bar and sprocket oil.
PAGE 20
EN POWXG1018 14 NOISE Noise emission values measured according to relevant standard. (K=3) Acoustic pressure level LpA 99 Acoustic power level LwA 115 ATTENTION! Wear hearing protection when sound pressure is over 85 dB(A). aw (Vibration) Max 11.8 m/s² K = 1,5 m/s² 15 STORING A CHAIN SAW Caution: never store a chain saw for longer than 30 days without performing the following procedures. Storing a chain saw for longer than 30 days requires storage maintenance.
PAGE 21
POWXG1018 Engine hesitates. Incorrect carburetor mixture adjustment setting. Air filter is plugged. Old or improperly mixed fuel. No power under load. Incorrect carburetor mixture adjustment setting. Old or improperly mixed fuel. Air filter is plugged. Fouled spark plug. Runs erratically. Incorrectly gapped spark plug. Plugged spark arrestor. Dirty air filter. Smokes excessively. Incorrect carburetor mixture adjustment setting. Incorrect fuel mixture.
PAGE 22
EN POWXG1018 18 ENVIRONMENT Should your appliance need replacement after extended use, do not discard it with the household rubbish but dispose of it in an environmentally safe way. Please dispose of used motor oil in a manner that is compatible with the environment. We suggest you take it in a sealed container to your local service station for reclamation. Do not throw it in the trash or pour it on the ground. 19 DECLARATION OF CONFORMITY VARO N.V.