Submittal Sheet

ManualsBrandsPowers ManualsDigital IntelliStation Jr. Smart Mixing Valves1-1/2" Inlet IntelliStation Jr. Digital Water Mixing Valve

* The wetted surface of this product contacted by consumable water contains less

than 0.25% of lead by weight.

** With equal pressure

*** Minimum ﬂ ow when IntelliStation is installed at or near hot water source recircu-

lating tempered water with a properly sized continuously operating recirculating

pump. (5GPM minimum)

**** low limit cannot be less than the cold water temperature. For best operation,

hot water should be at least 2°F above desired set point.

LEAD FREE

ES-P-INTELLISTATIONJR.

Job Name

–––––––––––––––––––––––––––––––––––––––––––

Contractor

––––––––––––––––––––––––––––––––––––––––––––

Job Location

–––––––––––––––––––––––––––––––––––––––––

Approval

–––––––––––––––––––––––––––––––––––––––––––––

Engineer

–––––––––––––––––––––––––––––––––––––––––––––

Contractor’s P.O. No.

––––––––––––––––––––––––––––––––––

Approval

–––––––––––––––––––––––––––––––––––––––––––––

Representative

––––––––––––––––––––––––––––––––––––––––

Powers product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,

please contact Powers Technical Service. Powers reserves the right to change or modify product design, construction, specifications, or materials with-

out prior notice and without incurring any obligation to make such changes and modifications on Powers products previously or subsequently sold.

IntelliStation

Jr.

Digital Water Mixing Valve

Features

• Programmable set point range 60°F to 180°F for wide range of temperature

• Lead Free* construction to comply with lead free* installation requirement

• 3.5" full-color, user-selectable touch screen display

• High temperature Sanitization mode to address water born bacteria

• Integral check valves on hot and cold inlets to prevent cross flow

• In case of power failure, valve flows full cold for safety

• Configurable on location. Does not require factory pre-programming, lap top

or special software

• Control module support BAS (Building Automation System) communication

with BACnet MSTP and Modbus protocols. It is native to the unit and does

not require an add on module

• Mixed outlet temperature can be adjusted/monitored at the valve or

remotely by BAS (Building Automation System)

• Includes single operating sensor for a mixed outlet temperature reading

• Pass code protected for security

• Programmable hi/lo temperature alert

• Programmable schedule for setback of temperature

• Real time clock for time stamping of error messages

• Control water temperature ± 2°F in accordance with ASSE 1017

• Wi-Fi enable for software upgrades

Specifications

Maximum Operating Pressure......................... 200psi (1379kPa)

Maximum Hot Water Temperature .................. 200°F (93°C)

Minimum Hot Water Supply

Temperature** .................................... 2°F (1°C) above set point

Hot Water Inlet Temperature Range ................ 120-180°F (49-82°C)

Cold Water Inlet Range .................................. 39-80°F (4-26°C)

Minimum Flow *** ........................................ 0.5gpm (1.89lpm)

Temperature Adjustment Range**** ................ 60-180°F (16-82°C)

Listing /Compliance ....................................... ASSE 1017, cUPC, NSF

CSA 24/UL873, Bacnet Testing Laboratories (BTL), CE

Weight ......................................................... LFIS075VL 13lb (6kg)

LFIS100VL 17lb (8kg)

LFIS150VL 16lb (7kg)

LFIS200VL 19lb (9kg)

Ambient Temperature ................................... 32°F (0°C) to 122°F (50°C)

Ambient Humidity .......................................... 0 - 90 RH non-condensing

SUITABLE FOR INDOOR USE ONLY

Technical Specification

Power ................................ 115-230 V (ac) ± 10%, 50/60 Hz, 20 VA

Actuator Load ...................... 24 V (dc), 0.55 A, 13 W

1017

The information contained herein is not intended to replace the full

product installation and safety information available or the experience of

a trained product installer. You are required to thoroughly read all instal-

lation instructions and product safety information before beginning the

installation of this product.

NOTICE

E365015

Temp. Ind. and Reg. Equip.

LFIS150VL

Summary of content (3 pages)

PAGE 1
ES-P-INTELLISTATIONJR. Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor –––––––––––––––––––––––––––––––––––––––––––– Job Location ––––––––––––––––––––––––––––––––––––––––– Approval Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. –––––––––––––––––––––––––––––––––– Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative –––––––––––––––––––––––––––––––––––––––– ––––––––––––––––––––––––––––––––––––––––––––– LEAD FREE* IntelliStation® Jr.
PAGE 2
Capacity Ordering Code Flow Capacity at 50-50 mixed ratio Pressure Drop Across Valve Model Min System Draw+ CV LFIS075VL 0.5 7.3 LFIS100VL 0.5 17.5 LFIS150VL 0.5 22.5 LFIS200VL 0.5 39.
PAGE 3
Typical Specification Lead free* digital water temperature control and monitoring system shall feature 3.5" full-color touchscreen interface which is configurable on location and does not require factory pre-programming. System shall control water temperature to +/- 2°F in accordance with ASSE 1017 and resist "temperature creep" during periods of low/zero demand.