INSTRUCTION MANUAL Electric Compact Circular Saw Model # PS4005 Have product questions or need technical support? Please feel free to contact us! Website: www.Amerisuninc.com Toll free: 1-800-791-9458 M-F 9-5 EST Email: support@amerisuninc.
CONTENTS Technical data…...………………………………………………………... General safety rules…….……………………………………………….... Electrical information…………………………………………………… Knowing your electric Compact Circular Saw..………….….………… Assembly instruction…………………………………………….………. Operating instruction…………………………………………………....... Maintenance……………………………………………………..……….. Exploded view…………………………………………………………… Parts list…………………………………………………………………... Warranty………………………………………………………………….
GENERAL SAFETY RULES Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE. WORK AREA SAFETY • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Definitions: Safety Alert Symbols and Words • This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risks of personal injury or property damage. • DANGER: Indicates an imminently hazardous situation which if not avoided, will result in death or serious injury. • WARNING: Indicates a potentially hazardous situation which, if not avoided could result in death or serious injury.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. • ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT: • WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
ELECTRICAL INFORMATION Guidelines for using extension cords When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gauge number, the heavier the cord.
KNOWING YOUR ELECTRIC COMPACT CIRCULAR SAW Fig 1 Fig 2 8
1 3 5 7 9 11 13 laser generator Blade clamp screw Unlock button Laser Depth setting clamp Lock lever knob for angle adjustment Saw blade 2 4 6 8 10 12 14 Edge guide locking screw Lower guard Switch trigger Spindle lock button Lower guard Dust extraction nozzle Baseplate ASSEMBLY INSTRUCTION Check for damage to the tool, parts and accessories which may have occurred during transportation. Take some time to read this manual carefully and understand all the content prior to assembly and operation.
6. Reinstall the outer flange, washer and tighten the blade clamp screw (3) by turning it counterclockwise with the wrench provided. 7. Make sure the saw blade (13) can turn freely by turning the blade by hand when release the spindle lock button. Make sure counterclockwise is locking saw blade. Fig. 7 Bevel Angle Adjustment (Fig 7) 1. Loosen the edge guide locking screw (2). 2. Slide the edge guide (C) through the slots in the base plate (14) to the desired width. 3.
OPERATION INSTRUCTION Switching on and off Note: Before engaging the on/off switch, check the saw blade to see if it is fitted properly and runs smoothly, and the blade clamp screw is well tightened. Connect the plug to the power supply. To start the tool, depress the unlock button (5) and press the switch trigger (6). Release the trigger (6) to turn the tool off. Depth adjustment Loosen the cutting depth setting clamp (9) by lifting the lock lever.
Cutting large sheets Large sheet or boards require support to prevent bends or sags. If you attempt to cut without levelling and properly supporting the work piece, the blade will tend to bind, causing kickback. Support the panel or board close to the cut. Be sure to set the blade adjustment so that you can cut through the material without cutting into the table or workbench. Suggestion: use two by fours to support the board or panel to be cut.
MAINTENANCE Warning: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Regular cleaning is required for the safe operation of the tool, as an excessive buildup of dust will prevent the tool from operating correctly. The dust extraction hose (B) may block and require cleaning occasionally, especially if damp wood is being cut. 1.
EXPLODED VIEW 14
PARTS LIST Item Stock# Description laser cover Qty Item Stock# Description Qty 1 41 PS4005-041 saw blade 1 1 PS4005-001 2 PS4005-002 spring holder 1 42 PS4005-042 outer flange 1 3 PS4005-003 tower type spring 1 43 PS4005-043 saw blade forcing screw M6*!4 1 4 PS4005-004 button cell 2 44 PS4005-044 spring 1 5 PS4005-005 ST4.
TWO (2) YEARS LIMITED WARRANTY Power Smart® is committed to building tools that are dependable for years. Our warranties are consistent with our commitment and dedication to quality. TWO (2) YEARS LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE. Power Smart (“Seller") warrants to the original purchaser only, that all Power Smart consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.