INSTRUCTION MANUAL Pneumatic 15-Degree Coil Roofing Nailer Model # PS6110 Have product questions or need technical support? Please feel free to contact us! Website: www.Amerisuninc.com Toll free: 1-800-791-9458 M-F 9-5 EST Email: support@amerisuninc.
CONTENTS Technical data…...………………………………………………………... General safety rules…….………………………………………………... Knowing your coil roofing nailer ..……………………………………… Assembly ………………………………………………………………… Operating instruction…………………………………………………...... Maintenance.……………………………………………………………… Troubleshooting………………………………………………………….
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert, and knowing how your coil roofing nailer works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions. WARNING: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
contact trip is adjusted when the tool is connected to the air supply and nails are loaded, accidental discharge may occur. Connect tool to air supply before loading fasteners, to prevent a fastener from being fired during connection. The tool driving mechanism may cycle when tool is connected to the air supply. Do not load fasteners with trigger or contact trip depressed, to prevent unintentional firing of a fastener.
Refer to the Maintenance and Repairs sections for detailed information on the proper maintenance of the tool. Always operate the tool in a clean, lighted area. Be sure the work surface is clear of any debris and be careful not to lose footing when working in elevated environments such as rooftops. Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a co-worker.
• When using the sequential trip trigger, do not actuate the tool unless the tool is placed firmly against the workpiece. Do not drive nails blindly into walls, U floors or other work areas. Fasteners driven into live electrical wires, plumbing, or other types of obstructions can result in injury. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
KNOWING YOUR COIL ROOFING NAILER F E C B A G H D A C E G Magazine Actuation mode selector 3/8" Air quick-connect connector Workpiece contact trip B D F H Trigger Depth-of-drive adjustment Exhaust deflector Shingle guide Unpacking Unpack the coil roofing nailer and all its parts, and compare against the list below. Do not discard the carton or any packaging materials. Please call 1-800-791-91458 or E-mail us at support@amerisuninc.com if any parts are damaged or missing.
ASSEMBLY WARNING: Disconnect air line from tool and remove fasteners from magazine before making adjustments or personal injury may result. AIR FITTING This tool uses a 3/8" N.P.T. male plug. The inside diameter should be 0.180" (4.6 mm) or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply. WARNING: Always use couplings that relieve all pressure from the tool when it is disconnected from the power supply.
Loading WARNING: Keep the tool pointed away from yourself and others. Serious personal injury may result. WARNING: Never load nails with the contact trip or trigger activated. Personal injury may result. When replacing nails in your model PS6140, follow these guidelines: Nail Type: 15 degree coil Length: 3/4"-1-3/4" Capacity: 120 pcs Fig.1 To load your nailer: 1. Disconnect nailer from the air supply! Fig.2 2. Squeeze the latch shown in Fig. 1, then open the feeder cover and magazine, as shown in Fig.
To operate your nailer: If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the oil the quick connect fitting where the nailer connects to the air supply. 1. Connect the air supply to the quick connect fitting. 2. Depress the safety nose mechanism flat against the work surface, and pull the trigger. 3. Check the nail penetration depth.
Selecting Actuation Mode The selectable trigger can be set to either Single Sequential Actuation mode or Contact Actuation mode. 1. Push in and hold the Actuation Selector. 2. Rotate the Selector to Single Sequential Actuation (T) or Contact Actuation (TT). 3. Release the Actuation Selector. NOTE: Be sure the selector is snapped into position. Understand the actuation process before use Air supply 1. Use clean, Dry and regulated compressed air at 70-110 PSI (4.8-7.5bar). 2.
MAINTENANCE WARNING: Disconnect the tool from the air compressor before adjusting, clearing jams, servicing, Relocating and during non-operation. 1. Regular lubrication of the tool is required. Add 2 to 6 drops of lubricant oil into the air inlet before each work day or after 2 hours of continuous use depending on the characteristic of work piece or type of fasteners. 2. Check and change all worn or damaged o-rings, seals, etc. Tighten all the screws and caps to avoid personal injury. 3.
TROUBLE SHOOTING The following form lists the common operating system with problem and solutions. Please read the form carefully and follow it. WARNING: If any of the following symptoms appears during your operating, stop using the tool immediately, or serious personal injury could result. Only a qualified persons or an authorized service center can perform repairs or replacement of tool. Disconnect tool from air supply before attempting repair or adjustment.
Qty 3 Item Stock # 49 Spring washer 11 50 PS6110-049 PS6110-050 Sealing washer 1 Exhaust port 1 51 PS6110-051 O ring 16x1.6 1 Valve seat 1 Item Stock # 1 PS6110-001 Description Bolt M6X10 2 PS6110-002 PS6110-003 3 Description Split washer 3 Qty 1 4 PS6110-004 Bolt M6x25 8 52 PS6110-052 5 PS6110-005 Cylinder cap 1 53 PS6110-053 O ring 6.1x1.8 1 6 PS6110-006 Cylinder cap bumper 1 54 PS6110-054 O ring 6.
TWO (2) YEARS LIMITED WARRANTY PowerSmart® is committed to building tools that are dependable for years. Our warranties are consistent with our commitment and dedication to quality. TWO (2) YEARS LIMITED WARRANTY OF POWER SMART PRODUCTS FOR HOME USE. PowerSmart (“Seller") warrants to the original purchaser only, that all PowerSmart consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.