Model No. AF1045 Owner’s Manual REMOTE CONTROLLED 3-SPEED AIR FILTRATION SYSTEM QUESTION... 1•847•780•6120 Visit us on the web at powertecproducts.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION SAFETY RULES PAGE 1 PRODUCT SPECIFICATIONS Controls. . . . . . . . . . . . . . . . . . . . Manual or Remote Control Remote Control Distance. . . . . . . . . . . . 65 feet (20 meters) ASSEMBLY 2 Number of Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Motor Speeds (RPM) . . . . . . . . . . . . . . . . . . . 750/960/1200 Air Flow (CFM) . . . . . . . . . . . . . . . . . . . . . . . .
WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by operation of power tool contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.
SPECIFIC SAFETY RULES 2 2 SPECIFIC SAFETY RULES FOR AIR FILTRATION SYSTEM Be aware of general power tool safety. Make sure all the safety rules are understood. • To reduce the risk of electrical shock, do not expose air filtration to water or rain. • Disconnect the machine from power source whenever adjusting or replacing any parts. • Never duct a machine directly into the air filtration system. • Do not plug air filtration system in unless switch is in the “OFF” position.
• Follow the instructions under Changing the Filters to replace the filters correctly. Refer to Figure 1 to 8 This air filtration system is specifically designed to circulate and filter non-metallic dust, which is generated throughout the work area. The unit can be located on a work bench, hung from an overhead support or mounted to the ceiling or wall. When selecting a location ensure the power source is easy to access. Ensure the remote control is within 65 feet of the control panel with no obstructions.
ASSEMBLY Hanging Mount • With assistance raise and secure the air filtration system eye bolts to the four hanging lines (Figure 7). Tools required for assembly: No. 2 Phillips screwdriver (not supplied) Figure 7 Anchor (not supplied) 10 mm wrench (not supplied) NOTE: Hang the unit at least 7 Feet above floor level and away from corners and any heating or cooling vents. 4 • Remove four screws from the cabinet top (Figure 5). NOTE: Save the four screws for future use.
Do not permit fingers to touch the terminals of plug when installing or removing from outlet. WARNING Do not connect to the power source until the machine is completely assembled. The machine is wired for 120 volts, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the “OFF” position. Running the unit on voltages which are not within range may cause overheating and motor burn-out.
OPERATION 6 6 OPERATION Refer to Figure 11, 12 TO TURN THE UNIT OFF This air filtration system can be controlled using the remote control (Figure 11) or the control panel (Figure 12) located at the rear of the unit. Press the OFF button on the remote control or the control panel to turn the unit off. NOTE: The filtration timing can ONLY be controlled with the remote. Figure 11 ON/SPEED CONTROL Press the ON/SPEED button on the remote control or the control panel.
WARNING Disconnect the machine from power source whenever adjusting or replacing any parts. CHANGING THE FILTERS Refer to Figure 13 The inner and outer filters should be replaced and / or cleaned depending on the amount of usage and the environment of your workshop. Clogged filters will reduce the amount of air circulation. • Lift up on the clips located at the top and bottom of the cabinet and remove the outer filter. • Pull the inner filter from the cabinet.
TROUBLESHOOTING TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE(S) Motor does not run 1. 5 8 CORRECTIVE ACTION Machine not plugged in 1. Plug power cord into electrical receptacle 2. ON/SPEED button is in "OFF" position 2. Press the ON/SPEED button to turn unit on 3. 4. 5. Power switch or cord is faulty Blown fuse Remote control is not working 3. 4. 5.
NOTES NOTE 9
PARTS LIST 10 10 AIR FILTRATION SYSTEM PARTS ILLUSTRATION
Key# Part# Description 11 Qty Key# Part# Description 1045-028 Handle 2 PARTS LIST AIR FILTRATION SYSTEM PARTS LIST Qty 1 1045-001 PCB box 1 28 2 1045-002 Nut M5 4 29 1045-029 Flange Nut 4 1045-030 Remote Box Cover 1 3 1045-003 Ground Wire 1 30 4 1045-004 Connector Wire 18AWG 1 31 1045-031 Remote Box-Down 1 5 1045-005 Wire Nut 1 32 1045-032 Battery Spring 1 6 1045-006 Flat Washer 5 mm 2 33 1045-033 AA Battery 2 1045-034 Remote Box-UP 1 7 1045-007
WARRANTY 12 WARRANTY Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 1 year from the date of purchase. This guarantee does not affect your statutory rights. 12 SOUTHERN TECHNOLOGIES LLC.
NOTE
Southern Technologies, LLC Waukegan, IL 60087
