Model No. BD1500 Owner’s Manual 1" x 5" Belt/Disc SANDER Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION SAFETY RULES PRODUCT SPECIFICATIONS PAGE 1 Work Preparation Work Area Preparation Tool Maintenance Tool Preparation ASSEMBLY RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3450 2 PARTS ILLUSTRATION & LIST WARRANTY Belt Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1" x 30" Belt Table Dimensions. . . . . . . . . . . . . . . . . . . . . . . 5" x 5" Disc Diameter . . . . . . . . . . . . . . . . . . . . . . . .
WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by operation of power tool contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.
ASSEMBLY ASSEMBLY 2 UNPACKING Refer to Figure 1. Check for shipping damage. Check immediately whether all parts and accessories are included. The sander comes assembled as one unit. Additional parts which need to be fastened to sander, should be located and accounted for before assembling.
To prevent trapping the workpiece or fingers between the table and the sanding disc adjust the sanding disc table to a maximum of 1/16" from the sanding disc. • The screws to attach the lower belt guard are assembled to the frame for shipping purposes, remove these screws and attach the lower belt guard as shown. • Slide the square headed bolt throught the frame and place the star washer on the square headed bolt.
ASSEMBLY • Loosen the locking lever and set screw. Slide the sanding belt table in or out until it is 1/16" from the from of the sanding belt. See Figure 8. • Ensure the sanding belt table measures a maximum of 1/16" from the backstop. To adjust see the To Adjust Sanding Belt Table paragraph in this section. • Place a combination square on the table with the ruler side against the back stop. Set the table 90° to the backstop. REPLACING THE SANDING DISC • Tighten the locking lever.
Figure 11 Refer to Figure 10 The backstop is a surface to sand against. The backstop can be removed for polishing and contour sanding. Bolt Flat Washer Sander Rubber Washer • Remove screws and washers securing backstop. Place screws, washers and backstop in a safe place for future use.
ASSEMBLY • Do not modify plug provided. If it will not fit in outlet, have proper outlet installed by a qualified electrician. Use only 3-wire extension cords, that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Figure 12. Figure 12 Extension Cord Length Wire Size…………….. A.W.G. Up to 25 ft…………… 16 gauge NOTE: Using extension cords over 25 ft. long is not recommended.
ON/OFF SWITCH Refer to Figure 15 The sander is equipped with a keyed switch to prevent unauthorized use of the sander. CAUTION Remove the safety key whenever the sander is not in use. Place the safety key in a safe place and out of the reach of children. 7 The sanding belt rotates counterclockwise or downward toward the table or backstop.
MAINTENANCE 8 MAINTENANCE WARNING For your own safety, turn the switch OFF and remove the plug from the electrical outlet before adjusting or performing maintenance or lubrication work on the belt/disc sander. GENERAL MAINTENANCE 8 Before using, check to make sure parts are not damaged, missing, or worn; check for alignment of moving parts, binding of moving parts, improper mounting, or any other conditions that may affect the sander operation.
SYMPTOM Sanding Grains easily rub off belt or discs. POSSIBLE CAUSE(S) 1. Sanding belt/disc has been stored in an incorrect environment. 2. Sanding belt/disc has been damaged or folded. CORRECTIVE ACTION 1. Ensure sanding accessories are stored away from extremely hot or dry temperatures. 2. Store sanding accessories flat – not bent or folded. Deep sanding grooves or scars in workpiece. 1. Sanding belt/disc grit is too coarse for the desired finish. 2. Workpiece sanded across the grain. 3.
PARTS LIST 10 10 1"X 5" BELT/DISC SANDER PARTS ILLUSTRATION
Description Description 11 Key# Part# Qty Key# Part# 1 2 3 4 5 6 7 8 9 10 11 12 BD1500001 BD1500002 BD1500003 BD1500004 BD1500005 BD1500006 BD1500007 BD1500008 BD1500009 BD1500010 BD1500011 BD1500012 Hex head bolt M8×18 Spring washer 8 Falt washer 8 Rubber foot Nut M4 Base Set screw M5×12 Driving wheel Locking nut M10 Falt washer 10 Retainer ring 15 Bearing 6202 2 2 2 4 2 1 1 1 1 2 2 2 35 36 37 38 39 40 41 42 43 44 45 46 BD1500035 BD1500036 BD1500037 BD1500038 BD1500039 BD1500040 BD1500041 BD15
WARRANTY 12 WARRANTY Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. 12 SOUTHERN TECHNOLOGIES LLC.
WARRANTY DISCLAIMER To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, that cannot be disclaimed under state law are limited to one year from the date of purchase. Southern Technologies LLC. is not responsible for direct, indirect, incidental or consequential damages.
Southern Technologies, LLC 206 Terrace Drive Mundelein, Illinois 60060
