Model No. DC5370 Owner’s Manual Wall Mount Dust Collector QUESTION... 1•847•780•6120 Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION PRODUCT SPECIFICATIONS PAGE SAFETY RULES 1 Motor Speed...................................................... 3450 RPM Work Preparation Work Area Preparation Tool Maintenance Tool Operation ASSEMBLY Bearings....................... Sealed & Permanently Lubricated Cord Length.............................................................. 6 Feet Air Suction Capacity............................................
WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks and cement and other masonry products.
SAFETY RULES SPECIFIC SAFETY INSTRUCTIONS 2 WARNING Read and understand the instruction manual before operating the dust collector. Basic precautions listed below should always be followed when using your dust collector to reduce the risk of injury, electrical shock or fire. 2 • This dust collector is designed to collect sawdust only. • Never attempt to use this dust collector to vacuum water or any other liquids. • Never try to use this dust collector to collect large wood pieces.
Flange Bolt Wall Mount Bracket A Motor Bracket • If mounting to a framed wall attach the mounting bracket to a support board. Attach the support board with lag screws (not supplied). 4. Hang the dust collector onto the wall mounting bracket. 5. Place the adhesive foam strip (supplied) around the dust collector outlet port. 6. Place the dust collector bag onto the outlet port and secure in place with the quick release bag clamp (supplied).
ASSEMBLY GROUNDING INSTRUCTIONS WARNING Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock. 4 • Check with a qualified electrician if you do not understand grounding instructions or if you are in doubt as to whether the tool is properly grounded.
BASIC OPERATIONS ON/OFF Switch The keyed switch is intended to prevent unauthorized use of the dust collector. 1. To turn the dust collector ON insert the yellow key into the key slot in the center of the switch. 2. Push the key firmly into the slot, then push switch to the ON position to start the dust collector. 3. To turn the dust collector OFF push the switch to the down position. 4. Remove the yellow switch key, when the dust collector has come to a complete stop, by gently pulling it outward.
MAINTENANCE MAINTENANCE 6 GENERAL MAINTENANCE WARNING Make sure the machine is turned off and the cord is disconnected from the power source before servicing and removing/replacing any components on the machine. 6 • Check the dust collector daily for loose mounting bolts, screws, damaged wires, worn switch, full collection bag and any other unsafe condition. • The impeller screw may loosen with use.
SYMPTOM POSSIBLE CAUSE(S) 7 CORRECTIVE ACTION Motor will not start 1. Low voltage 2. Open circuit in motor or loose connections 3. Defective switch 4. Defective capacitor 5. Switch key is removed 1. Check power line for proper voltage 2. Inspect all lead connections on motor for loose or open connection 3. Replace switch 4. Replace capacitor 5. Insert switch key Motor will not start; fuses blown or circuit breakers are tripped 1. Short circuit in line cord or plug 1.
PARTS LIST 8 WALL MOUNT DUST COLLECTOR PARTS ILLUSTRATION 8 WALL MOUNT DUST COLLECTOR PARTS LIST Key No.
WARRANTY WARRANTY 9 Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. SOUTHERN TECHNOLOGIES LLC.
Southern Technologies, LLC 3816 Hawthorn CT, Waukegan, IL 60087
