Model No. MT4009 Owner’s Manual TABLE SAW STAND QUESTION... 1•847•780•6120 Visit us on the web at www.powertecproducts.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION SAFETY RULES PAGE 1 PRODUCT SPECIFICATIONS Net Weight: .......................................35.3 lbs (16 kg) Maximum Weight Capacity: ..............331 lbs (150 kg) ASSEMBLY 2 Stand Height: ....................................22-5/8" (57.
WARNING For your own safety, read all of the rules and precautions before operating tool. WARNING Always follow proper operating procedures as defined in this manual even if you are familiar with use of this table saw stand or any tool used with this stand. Remember that being careless for even a fraction of a second can result in severe personal injury. You must be familiar with the use of any tool or accessory used with this table saw stand.
ASSEMBLY ASSEMBLY 2 2 UNPACKING TOOLS NEEDED Refer to Figure 1 Check for shipping damage. Check immediately that all parts and accessories are included.
Attach the Footrest and Feet 3 • Repeat with other wheel. Figure 6 Refer to Figure 4–5 Raised Hub • Slide the footrest onto the main frame and secure with four button head screws and four hex locking nuts (two on each side). Flat Washer Main Frame • Screw the feet into the footrest as shown in Figure 5. The adjustable nut on the feet can be used to level and adjust the height of the stand.
ASSEMBLY Attach the Lever Assembly Mounting the Saw Refer to Figure 8–10 Refer to Figure 11 • Remove the bolt, washers, nut, large washer and spring from the lever assembly (See Figure 10). • Place the large washer and spring between the locking mechanism and the welded bracket as shown in Figure 8. 4 • Slide the lever through the holes in the frame, spring, large washer and into the locking mechanism. • Align the holes in the locking mechanism and the lever assembly rod.
WARNING 5 OPERATION OPERATION Figure 13 Do not use the table saw stand for scaffolding or as a ladder. Make sure to securely tighten all fasteners before using. Maximum capacity is 331 lbs (150 kg). Folding and Unfolding the Stand Refer to Figure 12 5 NOTE: Take care when folding and unfolding the stand to reduce the hazard of pinching hands and fingers. To Fold • While holding the handle, pull the lever and lift up on the handle, the table top will tilt down and the frame will fold close.
MAINTENANCE MAINTENANCE 6 GENERAL MAINTENANCE WARNING When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. To ensure safety and reliability, all repairs should be performed by a qualified service technician. 6 WARNING Keep the table saw stand dry, clean, and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum based products or any strong solvent to clean the table saw stand .
PARTS LIST TABLE SAW STAND PARTS ILLUSTRATION AND LIST 7 7 Key# 1 2 3 4 5 6 Part# MT4009001 MT4009002 MT4009003 MT4009004 MT4009005 MT4009006 7 8 9 10 11 MT4009007 MT4009008 MT4009009 MT4009010 MT4009011 12 13 14 15 16 MT4009012 MT4009013 MT4009014 MT4009015 MT4009016 17 18 MT4009017 MT4009018 19 20 MT4009019 MT4009020 Description Nut Locking Handle Flat Washer Locking Shaft Handle Hexagon Socket Button Head Screws Hex Locking Nut Tube Sleeve Wheels End Cap Wheel Housing Welded Part Wheel Bolt
WARRANTY 8 WARRANTY Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. 8 SOUTHERN TECHNOLOGIES LLC.
Southern Technologies, LLC, Waukegan, IL 60087
