FlexModule Mini User Guide For Balance 20X / 380X / 580X Jan 2023 Important Notes 1. Please handle the connectors with care as to not damage them. 2. LTE-A (CAT-6) and LTE-A Pro (CAT-12) FlexModule Minis have 2x cellular antenna connectors while LTE-A Pro (CAT-18) and 5G have 4x cellular antenna connectors. So if you are upgrading from LTE-A (CAT-6) or LTE-A Pro (CAT-12) to either LTE-A Pro (CAT-18) or 5G, you will require additional antennas. 3.
Procedure for changing the FlexModule Mini on the B380X/B580X Step 1: Power off the router. The router MUST be disconnected from power before starting the upgrade. Step 2: Disconnect all antennas. Step 3: Loosen the screws on the cover or the installed FlexModule Mini. Step 4: Remove the cover or module by pulling them out directly. https://www.peplink.
Step 5: Loosen the screws of the new FlexModule Mini in order to remove the module cover which is for the Balance 20X. Step 6: Install the 380X/580X module cover and tighten the screws. Step 7: Install the new module. Make sure it is correctly aligned before pressing the module firmly into place. The FlexModule Mini should sit flush with the router chassis. https://www.peplink.
Step 8: Tighten the screws until the FlexModule Mini sits flush and tight with the collar. Step 9: Reconnect the antennas. Step 10: Reconnect the power. https://www.peplink.
Procedures for changing the FlexModule Mini on the B20X Step 1: Power off the router. The router MUST be disconnected from power before starting the upgrade. Step 2: Disconnect all antennas. Step 3: Loosen the screws on the cover or the installed FlexModule Mini. https://www.peplink.
Step 4: Remove the cover or module by pulling it out directly. Step 5: Install the new module. Make sure it is correctly aligned before pressing the module firmly into place. The FlexModule Mini should sit flush with the router chassis. Step 6: Tighten the screws until the FlexModule Mini sits flush and tight with the collar. https://www.peplink.
Step 7: Reconnect the antennas. Step 8: Reconnect the power. https://www.peplink.
FCC Requirements for Operation in the United States Federal Communications Commission (FCC) Compliance Notice: For FlexModule Mini Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Radiation Exposure Statement This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps. https://www.peplink.
CE Statement for Pepwave Routers ( FlexModule Mini for MV31-W) https://www.peplink.
https://www.peplink.
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
UK Statement for Pepwave Routers ( FlexModule Mini for MV31-W) https://www.peplink.
https://www.peplink.
CE Statement for Pepwave Routers ( FlexModule Mini for MC7455 ) https://www.peplink.
https://www.peplink.
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
UK Statement for Pepwave Routers ( FlexModule Mini for MC7455 ) https://www.peplink.
https://www.peplink.
CE Statement for Pepwave Routers ( FlexModule Mini for EM7690 & EM7565 ) https://www.peplink.
https://www.peplink.
This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. contact as: https://www.peplink.com/ https://www.peplink.
UK Statement for Pepwave Routers ( FlexModule Mini for EM7690 & EM7565 ) https://www.peplink.
https://www.peplink.
