Model No. PL1252 Owner’s Manual 12-1/2" THICKNESS PLANER QUESTION... 1•847•780•6120 1•877•393•7121 Visit us on the web at www.powertecproducts.com You will need this manual for safety instructions, operating procedures, and warranty. Put it and the original sales invoice in a safe, dry place for future reference.
TABLE OF CONTENTS SECTION PAGE SAFETY RULES 1 PRODUCT SPECIFICATIONS Horsepower (Maxmum Developed).............................. 2 HP Voltage..........................................................................120 V Work Preparation Work Area Preparation Tool Maintenance Tool Operation Amperes..........................................................................15 A Hertz..............................................................................60 Hz Phase..................................
SAFETY RULES WARNING For your own safety, read and understand all warnings and operating instructions before using any tool or equipment. WARNING Some dust created by the operation of the power tool contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment.
2 UNPACKING ASSEMBLY • Check for freight damage before opening the package. If freight damage is noticed, file a claim with the carrier immediately. • Check to ensure all parts are accounted for. If any parts are missing, please contact the customer service center at 1-877-393-7121. • This Planer comes mostly assembled. It requires some additional assembling, installation, and adjustment before use. • Locate the following parts before assembling: Figure 1 Unpacking A A. Planer B.
Refer to Figure 2 and 3 • The planer handle can be installed to the top-right of the planer. • Insert handle onto elevation screw top. • Secure handle with bolt and flat washer using the enclosed wrench. • Insert plug into handle Figure 2 - Install Handle Handle with Knob POWER SOURCE WARNING Do not connect to the power source until the machine is completely assembled. The machine is wired for 120 Volts, 60 Hz alternating current.
ASSEMBLY Extension Cord Length Wire Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.W.G. Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 25 to 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 4 - 3-Prong Receptacle Grounded outlet Box NOTE: Using extension cords over 50 ft. long is not recommended.
OPERATION WARNING For our own safety, read the entire operating manual and safety instructions before using this tool. SAFETY PRECAUTIONS • Be aware of general power tool safety. Make sure all the safety rules are understood. • Disconnect the machine from power source whenever adjusting or replacing any parts. • Do not plug planer in unless switch is in the “OFF” position. • Keep hands away from all moving parts. • Wear eye protection or face shield during operation.
OPERATION 6 NOTE: When the machine is not in use, the machine should be locked in the “OFF” position to prevent unauthorized use. • To lock the machine, turn the switch to the “OFF” position. Pull the key out. The switch cannot be turned on without the key. • If the key is removed when the switch is at the "ON" position, the switch can be turned off but cannot be turned on again. • To unlock, place the key into the slot on switch unit until it snaps.
• Always use protective safety wear and observe safety rules. • Never stand directly in the pathway of the workpiece, including infeed and outfeed, to avoid injury. The operator should stand on the side of the elevation crank handle. • Feed the workpiece “WITH The Grain” as much as possible. That is, at the contact point, the grain points to the same direction as that of rotating cutterhead. For this planer machine, the grain direction on the top of workpiece should point toward the front of the machine.
MAINTENANCE 8 WARNING Figure 9 Turn the switch to the OFF position and disconnect the machine from power source before any maintenance. CHECK AND REPLACE THE BLADES Refer to Figure 9 and 10 • Locate the blade cover on the back of planer. Loosen and remove thumb screws from blade guard. • Identify the cutterhead inside. Watch for TWO sharp blades on the cutterhead. • Without touching the blades, carefully turn the cutterhead until it stops by the self-engaging latch.
Refer to Parts Illustration The rollercase level is checked in factory and should work properly. However, it can become out of alignment during shipping and handling. • If the rollercase is not level with the base, the depth-ofcut will not be even from side to side. The end result is tapered cut where the thickness on one side is different from the other side. This can result from uneven wear of the blade as well. Check to see blades are in good working order.
10 TROUBLESHOOTING SYMPTON POSSIBLE CAUSE(S) Motor will not start 1. Low voltage 2. Short circuit in line cord or plug Motor stalls or fails to reach full speed 1. Power overload 2. Low voltage from power supply 3. Undersized line cord Motor overheats 1. Motor overloaded 1. Check power supply for proper voltage 2. Inspect line cord and plug for faulty insulation or shorted connection 3. Short circuit in motor 3. Inspect connection on motor 4. Open circuit or loose connection in 4.
POSSIBLE CAUSE(S) SOLUTIONS Difficulties in adjusting rollercase elevation 1. Worn elevation screws 2. Dirty elevation screws or columns 3. Dirty chains or sprockets 4. Rollercase is not positioned level with planer base 5. Friction between rollercase and covers 1. Release rollercase lock 2. Replace elevation screws 3. Clean and lubricate elevation screws and columns 4. Clean and lubricate chains and sprockets 5. Adjust table and rollercase level properly 6.
12 12-1/2" THICKNESS PLANER PARTS ILLUSTRATION Figure 11
12-1/2" THICKNESS PLANER PARTS LIST Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 Part No. PL1250001 PL1251001 PL1251002 PL1251003 PL1251004 PL1250004.6 PL1250004.5 PL1250004.4 PL1250004.3 PL1250004.
14 WARRANTY Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12 months from the date of purchase. This guarantee does not affect your statutory rights. SOUTHERN TECHNOLOGIES LLC.
WARRANTY ADDITIONAL LIMITATIONS To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to one year from the date of purchase. Southern Technologies LLC. is not responsible for direct, indirect, incidental or consequential damages.
Southern Technologies, LLC 3816 Hawthorn Court, Waukegan, IL 60087
