OPERATOR’S MANUAL COMMERCIAL UPRIGHT VACUUM CLEANER MODEL PF99 WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
INDEX Important Safety Instructions................................. 3 Check the carton for shipping damage. Carefully unpack and inspect your new Powr-Flite vacuum for shipping damage. Each unit is tested and thoroughly inspected prior to shipping. If damage is discovered, immediately notify the transportation company that delivered your machine and request an inspection. As a manufacturer, we are unable to act upon any claim for concealed damage; you must originate the claim.
IMPORTANT SAFETYGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Connect to a properly grounded outlet only. See grounding instructions. • Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing.
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
PARTS IDENTIFICATION Handle grip Handle tube Cord storage hook On/Off switch Pig-tail Cord Dust cover handle Easy-carry handle Dust cover Accessory attachment opening 40' Extension cord Nozzle inlet Blow molded hose Model specification plate Cord lock Furniture guard Thermal reset Thermal reset instructions button Self-adjusting nozzle REPLACEMENT BAGS/FILTERS • X1999 - Genuine Powr-Flite Vacuum HEPA Filter Bags 25 pk.
HOW TO ASSEMBLE AND OPERATE THE VACUUM How to Attach the Handle to the Vacuum Cleaner The cleaner and the handle are packed separately. 1. After first removing the handle screw, insert handle into the hole on top of the vacuum cleaner. Make sure that the handle is positioned correctly with the cord hook on the backside of the handle.(Fig. 1). 2. Line up the small hole on the handle with the small hole on the vacuum cleaner and insert the screw. Make sure the screw is tightened securely. (Figs. 2 - 3). 3.
HANDLE ADJUSTMENTS The handle on this vacuum cleaner can be set to one of three positions – upright, middle, or low. How to Adjust the Handle 1. To release the handle, step on the PowrFoot label on the nozzle and tip the handle backwards. (Fig.1). 2. Middle position – for normal cleaning (Fig. 2). 3. Upright position – for when cleaning tools are used or for storage (Fig 3). Handle locks in this position. 4. Low position – for cleaning under furniture (Fig. 4). Fig. 2 Fig. 1 Fig. 3 Fig.
AUTOMATIC SELF-ADJUSTING RUG NOZZLE Your Powr-Flite upright vacuum cleaner is designed with an Automatic Self-Adjusting Rug Nozzle. No manual adjustments are required. The height of the rug nozzle is instantly and automatically adjusted to carpet pile height. This self-adjusting feature allows the rug nozzle to float evenly over all carpet pile surfaces.
HOW TO REPLACE THE DRIVE BELT CAUTION: First, unplug the vacuum cleaner. How to Remove the Bottom Plate. 1. Step on Power-Foot label and pull back to release handle. 2. Place vacuum cleaner in the low position. Then turn the vacuum cleaner over, exposing the underside. 3. Remove the lower plate by sliding the two locking tabs towards the center of the vacuum underside. (Fig. 1) How to replace the belt. 1. Turn the unit over and remove the lower plate as described in the preceding section. (Fig. 1) 2.
REPLACING THE AGITATOR ASSEMBLY Brushes should be replaced when they are worn or when the bristle does not touch a card that is held across the nozzle. You should replace all four brushes at the same time in order to maintain good cleaning efficiency. Remove E-clip first from agitator shaft by using screw driver. Then remove the end cap at right end by holding the agitator assembly. Pull out the agitator shaft from the left end. NOTE: Take care not to deform the agitator shaft.
THERMAL FUSE PROTECTION Your Powr-Flite vacuum cleaner comes equipped with a Manual Reset Thermal Fuse Protector. This thermal protector is designed to protect your vacuum cleaner from overheating due to a cutoff in airflow (i.e. clogged hose, operating the vacuum without a bag). Should this situation occur, the thermal fuse protector will safely shut off your vacuum cleaner to avoid any potential damage. To reset the thermal fuse: 1. Unplug the vacuum cleaner. 2.
For warranty information go to www.Powr-Flite.com A Tacony Company 3101 Wichita Court • Ft.
