XS 1200 Beam PR-2933M This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. http://www.pr-lighting.
INDEX 3 4 4 5 5 6 6 6 8 10 10 11 14 14 14 14 15 16 19 20 SAFE USAGE OF THE PROJECTOR INSTALLING THE PROJECTOR FITTING THE LAMP POWER SUPPLY – MAINS CONTROL CONNECTIONS DMX TERMINATOR SETUP OPTIONS-PROJECTOR CONFIGURATION TO SET THE DMX START ADDRESS OPERATION MENU ERROR MESSAGES REPLACING GOBOS DMX PROTOCOL LED INDICATION MAINTENANCE LUBRICATION KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES Please note that as part of our ongoing commitment to continuo
SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
INSTALL THE PROJECTOR Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of the base as shown above) To pass 2 SAFETY CORDS through 4 HOLES for safety! Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.
POWER SUPPLY-MAINS Connect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards.
DMX TERMINATOR In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX control signals. The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
Launch the projector. Press button ENTER or encoder knob more than 5 seconds to unlock panel. Press button FUNC to display DMX address; Press button UP and DOWN, you can set the address; Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has been enabled. Press button FUNC, it will return to the upper menu one by one.
OPERATION MENU 1st LEVEL PR LIGHTING XS SERIES XS 1200 BEAM DMX Address Reset 2nd LEVEL 3rd LEVEL DMX Address=001 DMX Address Reset Are You Sure? DMX Mode Config Settings Lamp Control Factory Settings (Press button DOWN/UP/ENTER at the same time to enter the sub-menu) Fixture type (WARNING：Never change the fixture type or the system will be damaged!) Colour Positions STEPPED Colour Positions LINEAR Pan DMX Invert OFF Pan DMX Invert ON Tilt DMX Invert OFF Tilt DMX Invert ON Pan Tilt Swap OFF Pan Tilt
On Always Display Mode Off After Delay Display Invert OFF Display Invert ON Disp Dim Level Min Disp Dim Level 1 Disp Dim Level 2 Disp Dim Level 3 Disp Dim Level 4 Disp Dim Level 5 Disp Dim Level 6 Disp Dim Level 7 Disp Dim Level 8 Disp Dim Level 9 Disp Dim Level full Display Contrast XX（XX：1-21） Display Invert Display Dimming Display Contrast Lamp Hours Lamp Hours=XX Total Hours Total Hours=XX Temperature Information Software Version Factory Setup Test Modes Self Test Lamp Status Lamp Manual Contr
ERROR MESSAGES In the course of launch, this unit examines automatically whether there are errors and if there are, it will display information as follows: Display Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err Sensor Err S1-M1 S1-M2 S1-M3 S1-M4 S1-M5 S2-M2 S2-M3 S2-M4 S3-M1 S3-M2 Message Colour wheel (1# drive board motor 1) error CYM-cyan (1# drive board motor 2) error CYM-yellow (1# drive board motor 3) error CYM-magenta (1# drive board motor 4) error
DMX PROTOCOL Short mode 1 2 Standard mode 1 2 Extended mode 1 FUNCTION Strobe 2 Dimmer 3 Dimmer Fine 3 3 4 CYM Macro 4 4 5 CYM-Cyan CYM-Cyan Fine CYM-Yellow CYM-Yellow Fine CYM-Magenta CYM-Magenta Fine 6 5 5 7 8 6 6 9 10 7 7 11 Colour Wheel DMX 000-010 Black 011-025 Open 026-225 Strobe speed from slow to fast 226-246 Macro 247-255 Open 000-003 004-255 000-255 000-016 017-035 036-054 055-073 074-092 093-110 111-128 129-255 000-255 Black Dimmer in 16 Bit precision Wh
195-255 Rainbow reverse rotation speed from fast to slow White Gobo1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Rotation speed from slow to fast Reverse rotation from slow to fast Gobo 1 shake speed from slow to fast Gobo 2 shake speed from slow to fast Gobo 3 shake speed from slow to fast Gobo 4 shake speed from slow to fast Gobo 5 shake speed from slow to fast Gobo 6 shake speed from slow to fast Gobo 7 shake speed from slow to fast white Gobo1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Rotation speed from slow t
15 16 16 17 18 21 22 23 19 24 20 25 Pan Fine Tilt Tilt Fine Pan & Tilt speed Control 000-255 000-255 000-255 Pan rotation in 16 precision Tilt rotation Tilt rotation in 16 precision 000-255 Pan&Tilt speed from fast to slow 000-047 048-080 081-112 113-144 145-168 169-200 201-223 224-255 Reserved Reset Reserved Lamp off ( stop in DMX value for 10 s) Reserved Lamp power reduced to 50% Reserved Lamp on (See remark below) Remark: If you intend to turn on/off the lamp via the last channel of the c
LED INDICATION Green Yellow Blue Red/Green On Off Flash On On Red Green DMX signal OK No DMX signal DMX signal error Setting the panel Power Running self test mode Reserved MAINTENANCE If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced.
TROUBLESHOOTING PROBLEM ACTION ¾ Check the fuse on the power socket. ¾ Replace the lamp. The lamp comes on but the projector ¾ Make sure that the projector is correctly configurated. doesn’t respond to the controller ¾ Replace or repair the DMX cable. The projector only functions intermittently ¾ Make sure the fan is working and not dirty. ¾ Check the lenses are not broken. ¾ Remove dust or grease from the lenses. ¾ Make sure the lamp is installed correctly.
TECHNICAL DATA VOLTAGES: 220V/230V AC，50/60Hz Option: 200V/240V AC，50/60Hz POWER CONSUMPTION: 1300W@220V LAMP: PHILIPS MSR Gold 1200 SA/2 DE Colour Temperature 7500°K Socket SFc10-4，double ends Manufacturers Rated Lamp Life 750 hours replacement Or OSRAM SharXS HTI 1200 W/D7/60 Colour Temperature 6000°K Socket SFc10-4，double ends Manufacturers Rated Lamp Life 750 hours replacement COLOURS: Smooth CYM colour mixing system with macro 1 wheel with 6 dichroic colour filters plus white With vari
DIMMER: 0-100% linearly adjustable SHUTTER: Double shutter blades, 0.3~25 F.P.S HEAD MOVEMENT: Pan 540º, Tilt 270º with auto position correction BEAM ANGLE: Focus 5°in 16 Bit precision Extended frost 1：9.5° Extended frost 2：11.5° CONTROL: DMX512, 3 pin and 5 pin interfaces RDM control protocol 16 channels in short mode, 20 channels in standard mode, and 25 channels in extended mode.
485 672 907 610 515 LIGHT OUTPUT: 11.5°Lux 9.5°Lux 5°Lux 4m 2m 0m 2m 4m 0 0 0 54065 63084 297675 13516 15771 74419 6007 7009 33075 3379 3943 18605 2163 2523 11907 5m 3m 1m 5° 9.5°11.5° 1m 3m 5m DISTANCE(m) 0m DIAMETER(m) DIAMETER(m) DIAMETER(m) 0 0 0 5m 10m 15m 20m 25m 0.45 0.91 1.00 0.90 1.82 2.00 1.35 2.73 3.00 1.80 3.64 4.00 2.25 4.55 5.
View side of no axletree M1-4 品红色 Magenta 变焦 M1-6A Dimmer 调光 View side of no axletree M2-3 自转图案盘 GOBO View side of no axletree M2-4 图案自转 Rotation GOBO View side of no axletree M2-5 频闪片1 SHUTTER A View side of no axletree M-5A Zoom M2-2 固定图案盘 FIX-GOBO View side of no axletree View side of no axletree M2-6 频闪片2 SHUTTER B View side of no axletree MOTOR6 M1-6B Dimmer 调光 MOTOR5 View side of no axletree MOTOR4 变焦 MOTOR3 M1-5B Zoom MOTOR2 View side of no axletree MOTOR1 V G S SENS1 SENS2
COMPONENT ORDER CODES NAME MAINS FILTER THERMOSTAT IGNITOR TRANSFARMER BALLAST CAPACITOR LAMP TILT DRIVE BELT PAN DRIVE BELT FOCUS MOTOR FIXED GOBO WHEEL MOTOR GOBO ROTATION MOTOR PRISM ROTATION MOTOR COLOUR WHEEL MOTOR ROTATING PRISM WHEEL MOTOR ROTATING GOBO WHEEL MOTOR PAN &TILT MOTOR SHUTTER BLADE MOTOR DIMMER MOTOR CYM MOTOR PAN/TILT DRIVE PCB MOTOR DRIVE PCB 1 MOTOR DRIVE PCB 2 MOTOR DRIVE PCB 3 DISPLAY PCB POWER BOARD PART NO.
/22
PR LIGHTING LTD.
