Owner’s Manual | LSP48 | 48” Lawn Sweeper Manual Contents Safety Instructions Assembly Operation Maintenance Parts Warranty Your Lawn Sweeper 2 4-13 2 11 14-15 16 Congratulations on your purchase of a new Precision Products, Inc. Lawn Sweeper. Your Lawn Sweeper has been engineered and built to give you the most dependable and best performing product possible.
Safety Instructions All power equipment can cause injury or property damage if operated improperly. Please read and observe the following safety rules and exercise caution at all times when operating equipment. Read and understand your tractor owner’s manual and towing safety rules, know how to operate your tractor before using any attachment. Never allow children to operate the towing vehicle. Do not allow adults to operate the vehicle without having read the owner’s manual or receiving proper instruction.
Carton Contents pages 3 & 4 14 16 15 12 11 17 13 5 10 9 6 1 8 4 3 2 7 Ref. Qty. Hitch Tube R.H. 10 1 Bag Frame Strap 1 Hitch Tube L.H. 11 2 Hopper Support Rod 3 1 Handle Assembly 12 1 Lower Hopper Side Tube R.H. 4 1 Clevis Plate (straight) 13 1 Lower Hopper Side Tube L.H. 5 1 Clevis Plate 14 1 Upper Hopper Side Tube R.H. 6 1 Hopper Bag 15 1 Upper Hopper Side Tube L. H.
22 23 32 29 25 26 24 28 29 28 31 30 Ref. Qty. Hex Head Bolt M8x65 27 2 Clevis Pin 08x25 (Not Shown) 2 Hex Head Bolt M8x50 28 1 Hitch Pin 20 2 Hex Head Bolt M8x40 29 2 Hitch Spacer 21 6 Allen Head Bolt M6x30 30 1 Angle Bracket 22 6 Nylock Nut M8 31 2 Tube Plug 23 10 Nylock Nut M6 32 4 Allen Head Bolt M6x40 24 7 Hitch Pin Clip 03 25 2 Clevis Pin 08x37 26 2 Clevis Pin 08x58 Ref. Qty.
Assembly Remove the Hardware Sack or (hardware may be attached to other parts) and all loose parts from the carton and verify that all the Parts and Fasteners shown on pages 3 and 4 are included. Assembly Instructions Note Right hand (R.H.) and Left hand (L.H.) are determined from the operator’s position while seated on the Tractor. 1. (Pre-Assembled at Factory) Assemble the Angle Bracket to the Sweeper Housing using a M8x16 Hex Head Bolt and a M8 Nylock Nut.
3. Attach the Hitch Tubes together using two M8x65 Hex Head Bolts and two M8 Nylock Nuts. Do not tighten yet. See Figure 3. R.H. Hitch Tube L.H. Hitch Tube M8x65 Hex Head Bolt Leave Gap In-between Tubing M8 Nylock Nut Figure 3 If your tractor hitch is between 11” to 13” of ground clearance see Figure 4. If your tractor hitch has between 8” to 11” of ground clearance see Figure 5. 4. Assemble the Clevis Plates to the Hitch Tubes using two M8x50 Hex Head Bolts and two M8 Nylock Nuts.
6. Attach the Height Adjustment Handle to the Height Adjustment Tube, using two M8x40 Hex Head Bolts and two M8 Nylock Nuts. Do not tighten yet. See Figure 6. M8 Nylock Nuts Handle Grip Height Adjustment Handle Height Adjustment Tube M8 x 40 Hex Head Bolt Figure 6 7. (Pre-Assembled At Factory) Insert a M8x20 Hex Head Bolt through Angle Bracket into the Height Adjustment Strap, attach the Flat Washer and secure with a M8 Nylock Nut. See Figure 7.
. Insert a M8x30 Carriage Bolt into the Height Adjustment Handle, into a Washer, into the Height Adjustment Strap, place another Washer onto the Bolt and secure with the Plastic Knob. See Figure 8. Height Adjustment Strap Hitch Spacers 9. (Pre-Assembled At Factory) Assemble the Connecting Bar to the Sweeper Housing by using two M6x12 Hex Head Bolts and secure with two M6 Nylock Nuts.
10. Turn a Rear Hopper Tube so that the Brace Holes in the middle of the tube face down. Slide the tube through the two loops sewn to the top rear seam inside of the hopper bag. See Figure 10. M6x30 Bolt Upper Hopper Side Tube Rear Hopper Tube (brace holes on bottom) Rear Hopper Tube Figure 10 M6 Nylock Nut 11. Insert the two Hopper Side Tubes through the stitched flaps on each side of the Hopper Bag.
13. Attach the ends of the Lower Hopper Side Tubes to the inside of the Upper Side Tubes using two 08x25 Clevis Pins, insert them from the inside and secure with two Hitch Pins Clips. See Figure 13. Upper Hopper Side Tube 08x25 Clevis Pin Hitch Pin Clip Hopper Bag Bottom Lower Hopper Side Tube Figure 13 14. Insert the Bag Frame Strap into the stitched sleeve along the front edge of the bag bottom. Attach the Bag Frame Strap to the Lower Hopper Side Tubes using two M6x30 Bolts and two M6 Nylock Nuts.
15. Secure the bag corners around the Lower Hopper Side Tubes by snapping the Bag Flaps to the Bag Bottom on both sides. See Figure 15. Flap Snap Figure 15 IMPORTANT: Do not over bend the Support Rods during the following step. Over bending will cause the steel rods to lose supporting tension. 16. Tip the Hopper onto it’s back to assemble the two Hopper Support Rods. Place the ends of each rod into the Upper and Lower Rear Hopper Tubes, bending the rod just enough to fit into the holes of the tubes.
17. Feel along the stitched flap on the Hopper Bag to locate the lower hole in each Upper Hopper Side Tube. Place a hole through both sides of the stitched flaps in alignment with the lower hole. See Figure 17. Upper Hole Lower Hole Upper Hopper Side Tube Figure 17 18. Insert a 08 x 58 Clevis Pin through the lower hole in each Upper Hopper Side Tube. Next assemble a Bag Arm Tube onto each Clevis Pin and secure with a Hitch Pin Clip. Place Vinyl Cap onto Bag Arm Tube. See Figure 18.
19. Secure the Rope to the top center of the Hopper Bag Frame. See Figure 19. Top Center Hopper Bag Frame Rope Figure 19 20. Attach the Hopper Bag to the Sweeper, slide the ends of the Bag Arm Tubes into the ends of the Sweeper’s Hitch Tubes and secure with two 08x37 Clevis Pins and Hitch Pin Clips. See Figure 20.
Exploded View 78 78 16 47 74 79 16 79 74 16 75 75 14
Parts List LSP48 Part No. Description Qty. #1-38 Hopper Rope 1 40-48 Connecting Bar 1 #2-38 Vinyl Cap 2 41-38 M6x12 Hex Head Bolt 2 #3-48 Hopper Frame Tube (Rear) 2 42-38 Dust Cover Retainer 2 #4-48 Bag Frame Strap 1 43-38 Inside Star Washer 2 #5-38 Hopper Support Rod 2 44-38 Brush Shaft Bushing 2 #6-48 Hopper Bag 1 45-38 Spacer Bushing 2 #7-38 Lower Hopper Frame Tube (L.H.) 1 46-38 Spacer for Axle 2 #8-38 Upper Hopper Frame Tube (L.H.
Manufacture’s Limited Warranty for Tow Behind Accessories The limited warranty set forth below is given by Precision Products, Incorporated with respect to new merchandise purchased and used in the United States, its possessions and territories. forth in this warranty provide the sole and exclusive remedy arising from the purchase. Precision Products, Inc.
