Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions
Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 Before You Begin ............................................................................................. 4 2 Preparations..................................................................................................... 5 3 4 5 6 7 Table of Contents Obtaining Service ........................................................................................................................ 4 Unpacking the Equipment .....
1 Before You Begin Thank you for adding the Precor Cardio Theater Integrated LCD Screen Option to your cycle. This option will add a new dimension to your workout. For proper installation, please read this guide thoroughly and follow the assembly instructions. Obtaining Service For information about product operation or service, refer to the Precor web site at www.precor.com.
Cardio Theater Integrated Bracket Assembly Instructions 2 Preparations Important: To attach the Cardio Theater Integrated Bracket, ask another adult for help. Do not attempt the assembly by yourself. Installation Requirements Assembly Tips Review these installation requirements before assembly: • Read all the notes on each page before completing that step. Remember to read and follow the instructions in this guide.
Cardio Theater Integrated Bracket Assembly Instructions 3 Preparing the Units The illustration shows how the Cardio Theater Integrated Bracket will look after you install it on the cycle. Recumbent Upright This section contains preparation instructions for the upright and recumbent cycles. The installation is the same on the two units. Note: The illustrations shown in this section depict the recumbent cycle installation, but the same steps apply to the upright units.
Cardio Theater Integrated Bracket Assembly Instructions 1. Remove the two plastic plugs located along the upright support. 2. Feed the coaxial/power cable through the upright support. Locate the coaxial/power cable provided with the LCD Screen. Feed the end of the coaxial/ power cable with two connectors (coaxial and power) into the upper hole on the upright support. Slide the cable and its two connectors down until you can the connectors through the lower hole. 3.
Cardio Theater Integrated Bracket Assembly Instructions 4. Use a ⁵⁄₃₂-inch hex key to loosen, but do not remove, the screw at the top right corner of the display console bracket. Important: Do not remove the screw! Loosening the right top screw keeps the display from sliding off the console bracket. A cutout in the bracket assembly flange fits around the screw. 4 5. Remove the remaining three screws that secure the display console. Loosen, but do not remove this screw.
Cardio Theater Integrated Bracket Assembly Instructions 4 1 2 Install the Bracket Assembly Pivot tube Bracket assembly 1. Remove the bracket cover. Loosen the bolts on the pivot tube using a ⁷⁄₃₂-inch hex key. Pull the bracket cover away from the assembly. Set it aside. 2. Feed the coaxial/power cable with its three connectors through the bracket assembly.
Cardio Theater Integrated Bracket Assembly Instructions 3. Fit the bracket assembly onto the display console bracket. Ask your assistant to lift the bracket assembly and position it along the back of the display console bracket. Make sure the bracket assembly slides into place so that the cutout at the top right flange fits around the top right screw. 3 Display console bracket Important: Make sure that the cable is not pinched between the bracket assembly and the display console bracket. 4.
Cardio Theater Integrated Bracket Assembly Instructions 5 Metal mounting bracket 2 3 Attach the LCD Screen Plastic cover Important: The screen spacer is used only for the Cardio Theater PVS4/5/15 LCD Screen. 1. To protect the LCD Screen for the next few steps, place it screen side down on a clean work surface. Important: Use proper materials to protect the LCD Screen while you remove the plastic cover and metal mounting bracket from the backside of the LCD Screen. LCD screen 2.
Cardio Theater Integrated Bracket Assembly Instructions 6. Fully tighten the bottom two screws. Use a Phillips-head screwdriver to fully tighten the bottom two screws. Leave the top two screws finger tight. 6 7 7. Connect the coaxial/power cable connectors to the LCD Screen. Attach the connectors—coaxial, power, and DVD—to the back of the LCD Screen. Note: If you do not have a DVD option, you can feed the DVD cable back into the pivot tube compartment so it is not hanging out. Power connector 8.
Cardio Theater Integrated Bracket Assembly Instructions 6 1 Reinstall the Bracket Cover Top of bracket cover Bracket cover 1. Prepare the fasteners for reinstalling the bracket cover. Push the washers and bearings toward the bolt heads so there is room for the bracket cover to slide in flush against the pivot tube. Important: Keep the bracket cover flanges flush with the pivot tube. The washers and bearings need to remain on the outside of the bracket flanges. 2.
Cardio Theater Integrated Bracket Assembly Instructions 7 Controller Bracket bar Connect the Controller and the Cables Rubber adapter mounts Note: Retrieve the rubber adapter mounts from the bracket assembly package. Retrieve the controller from the LCD Screen package. Controller cable 1. Connect the controller cable to the controller. A definite click is heard when the connector snaps into place inside its receptacle. 2. Place the rubber adapter mounts around the center of the bracket bar.
Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor and Cardio-Theater are registered trademarks of Precor Incorporated. Specifications subject to change without notice. Copyright 2005 Precor Incorporated. Precor web site: www.precor.com NOTICE: Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S.
