Assembly Guide CW-113
Important Safety Instructions When using exercise equipment, basic precautions should always be taken, including the following: • • Read all instructions before assembling the CW-113. These instructions are written for your safety and to protect the unit. Read each step in the assembly instructions and follow the steps in sequence. Do not skip ahead.
CW-113 Assembly and Maintenance Guide Table of Contents Important Safety Instructions ................................................................................................... 3 Obtaining Service .................................................................................................................... 3 Table of Contents 1 Preparations ................................................................................................... 5 2 Assembly Instructions ......................
CW-113 Assembly and Maintenance Guide 1 Preparations The CW-113 parts are inspected before shipment. Each unit contains several pieces that require assembly. You will need to obtain adult assistance during the assembly process. Unpacking the Equipment When you open the box, carefully unpack the pieces and lay them on the floor near the location where you plan to use them.
CW-113 Assembly and Maintenance Guide Hardware Kit Fastener Qty ³⁄₈ x ¾-inch Buttonhead screw (A) ³⁄₈-inch Split washer (B) ½-inch Washer (F) 2 ½-inch Lock nut (G) 1 ⁵⁄₁₆ x 3-inch Buttonhead screw (H) 4 14 2 ³⁄₈-inch Washer (D) 2 Preparations, continued Qty 12 ³⁄₈ x 2¾-inch Buttonhead screw (C) ½ x 5¼-inch Buttonhead screw (E) Fastener 1 ⁵⁄₁₆-inch Split washer (J) 10 ⁵⁄₁₆-inch Washer (K) 10 ⁵⁄₁₆ x 1¼-inch Buttonhead screw (L) 6 page 6
CW-113 Assembly and Maintenance Guide 2 Assembly Instructions Handlebar Assembly of the CW-113 takes about 50 minutes to complete. If this is the first time you have assembled this type of equipment, plan on allowing more time. Roller Pads Thigh Pad Be careful to open boxes and assemble components in the sequence presented in thie manual. Back Pad Open the Box Holder Assembly Use wire cutters to open the box and remove packing materials.
CW-113 Assembly and Maintenance Guide Assemble the Unit 1. Attach the Main Frame to the Stabilizer using four ¾-inch buttonhead screws (A) four ³⁄₈-inch split washers (B) Wrench tighten. 4 - ¾" buttonhead screws 4 - split washers Spring Cushion Note: Make sure the wheels on the Stabilizer are positioned as shown in the illustration. 2. Attach two Spring Cushions to the Main Frame using two 2¾-inch buttonhead screws (C) two ³⁄₈-inch split washers (B) two ³⁄₈-inch washers (D) Wrench tighten. 3.
CW-113 Assembly and Maintenance Guide 5. Pull on the Adjustment Pin and slide the Back Adjustment through the Main Frame. Release the Adjustment Pin while it is aligned with the Back Adjustment middle hole. Note: Make sure the Springs slide onto the posts on the bottom of the Back Support 6. Slide the Sleeve through the Back Support.
CW-113 Assembly and Maintenance Guide 8. Slide the Roller Bar through Holder Assembly, and then place a Round Cap onto each end of the Roller Bar. Slide the Round Caps against the Holder Assembly. 9. Slide a Roller Pad onto each end of the Roller Bar, followed by a Roller Cap. Place an Aluminum Cap on each end of the Roller Bar and tighten the set screws. Roller Bar 10. Tighten the set screws at the end of the Holder Assembly to secure the Roller Bar, then insert the Square Cap into the Holder Assembly.
CW-113 Assembly and Maintenance Guide Assemble the Pads 1. Attach the Back Pad to the Back Support using four 3-inch buttonhead screws (H) four 5⁄16-inch split washer (J) four 5⁄16-inch washers (K) Wrench tighten. 2. Attach the Thigh Pad to the Back Support using six 1¼-inch buttonhead screws (L) six 5⁄16-inch split washers (J) six 5⁄16-inch washers (K) Wrench tighten. This completes the assembly of the CW-113.
CW-113 Assembly and Maintenance Guide Clean the Pads and Assembly To clean the pads moisten a clean, soft cloth in a mild solution of soap and water and wipe the pads thoroughly. Dry the pads with a clean, dry cloth. Use the same procedure to clean the Main Frame and plastic parts. Frequently vacuum the floor underneath the CW-113 to prevent the accumulation of dust and dirt. If necessary, use the Back Support to lift the front end and tip the CW-113 onto its wheels to roll it to a different location.
Limited Warranty Precor, Incorporated (PRECOR) will repair or replace any of the following components which are defective as to materials or workmanship for products manufactured and sold after June 1, 1990: ICARIAN & STRETCH CENTER: Lifetime:Structural Steel Framework Five Years: Rotary Bearings, Weight Stacks, Pulleys, Guide Rods, Structural Moving Parts One Year: Cable, Linear Bearings, Springs Ninety Days: Upholstery, Handgrips, All Other Items Not Listed Not withstanding the above, all warranties prov
CW-113 Assembly and Maintenance Guide Notes: page 14
CW-113 Specifications Length: 64 inches (163 cm) Height: 39 inches (99 cm) Width: 30 inches (76 cm) Shipping weight: 131 lb (59.42 kg) Precor Incorporated 20031 142nd Avenue NE P.O. Box 7202 Woodinville, WA USA 98072-4002 Precor is a registered trademark of Precor Incorporated. Specifications subject to change without notice. Copyright 2007 Precor Incorporated. www.precor.com NOTICE: Precor is widely recognized for its innovative, award winning designs of exercise equipment. Precor aggressively seeks U.S.