Operating and Maintaining the P20 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Edition Information OPERATING AND MAINTAINING THE P20 CONSOLE P/N 300753-201 rev B Copyright © June 2011 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, and EFX are registered trademarks and Preva is a trademark of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions This apparatus (hereinafter referred to as the console) is intended to be shipped with new Precor exercise equipment (hereinafter referred to as the base unit). It is not packaged for individual sale. WARNING To prevent injury, the console must be attached securely to the base unit following all assembly and installation instructions shipped with the base unit. The console is intended to be connected to AC mains power through the furnished power supply ONLY.
4 Operating and Maintaining the P20 Console Il est conseillé de subir un examen médical complet avant d’entreprendre tout programme d’exercise. Si vous avez des étourdissements ou des faiblesses, arrêtez les exercices immédiatement. Do not allow children, or people unfamiliar with the operation of this equipment, on or near it. Do not leave children unsupervised around the equipment.
Important Safety Instructions 5 Proper Location for Equipment For all equipment other than treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the equipment, and 40 inches (1 meter) away from objects behind the equipment. For treadmills: Locate at least 40 inches (1 meter) away from walls or furniture on either side of the treadmill, and at least 80 inches (2 meters) away from objects behind the treadmill.
6 Operating and Maintaining the P20 Console Use the equipment only for its intended purpose as described in this manual. Do not use accessory attachments that are not recommended by Precor. Such attachments may cause injuries. Do not operate the equipment where aerosol (spray) products are being used or where oxygen is being administered. Do not use outdoors. Do not attempt to service the equipment yourself, except to follow the maintenance instructions in this manual.
Important Safety Instructions 7 In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be collected separately and to be reused, recycled, or recovered at end of life. Users of EEE with the WEEE label per Annex IV of the WEEE Directive must not dispose of end of life EEE as unsorted municipal waste, but use the collection framework available to customers for the return, recycling, and recovery of WEEE.
8 Operating and Maintaining the P20 Console Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING Per FCC rules, changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Important Safety Instructions 9 Electrical Recommendations: 120 V and 240 V Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. You should have received a power cable that meets your local electrical code requirements along with the equipment. Precor treadmills must be connected to a 20 amp individual branch circuit that can be shared only with one PVS.
10 Operating and Maintaining the P20 Console Electrical Recommendations: All Equipment Excluding Treadmills Note: This is a recommendation only. NEC (National Electric Code) guidelines or local region electric codes must be followed. For equipment fitted with a P80 console or Personal Viewing System (PVS) screen a separate power connection is required. For a 20 amp branch circuit up to 10 screens can be connected.
Table of Contents Important Safety Instructions ................................................... 3 Safety Precautions .................................................................................3 Hazardous Materials and Proper Disposal .................................... 6 Product Recycling and Disposal ....................................................... 6 Regulatory Notices for Cardiovascular Exercise Equipment ......................................................................
12 Operating and Maintaining the P20 Console
Chapter 1 Getting Started The P20 console offers administrators and members the ability to set defaults that meet their specific needs. Activating the Console for Self-Powered Equipment Precor equipment is either self-powered or externally powered using an optional power adapter. Self-powered equipment requires the user exercise to initialize the console. This section provides more detail about powering equipment.
14 Operating and Maintaining the P20 Console Optional Use of the Power Adapter An optional AC power adapter provides sustained power to the equipment. This adapter allows you to change settings without having to pedal the equipment. To purchase the power adapter, contact your dealer. If you purchase the optional power adapter, you must also purchase the internal cable kit. The kit supplies the cable, bracket, and fasteners that connect the power adapter to the lower electronics board.
Chapter 2 Setting Up the Console Use the System mode to configure settings in ways that benefit your users and your facility. The System menu is visible only to administrators and registered service technicians. Changes made to these settings are saved to the fitness equipment.
16 Operating and Maintaining the P20 Console Identifying Parts of the Console The following diagram provides information about the console keys. The number and actions of the console keys may differ slightly depending on the type of equipment. Figure 4: P20 Console Display Note: Some equipment has both an intensity (resistance) indicator and an incline indicator. Other equipment may only have one type of indicator. Table 1.
17 Setting Up the Console Number Part Name Details Enter key Workout key Displays preset workouts Input Up key Use to navigate user menus Input Down key Use to navigate user menus GO key Use to begin your workout Reset key (Pause/Reset on tread consoles) Intensity indicator Displays level of resistance. This window can appear on single and dual indicator equipment.
18 Operating and Maintaining the P20 Console On self-powered equipment, the battery initializes when you begin working out. You must maintain a minimum rate of motion for the Welcome banner to appear. PEDAL FASTER (or the equivalent message depending on the equipment type) appears in the display when the battery is low or when the rate of motion drops below the minimum requirements.
19 Setting Up the Console Event Log The software is able to detect a variety of events. The event log holds a maximum of 30 events. After the log reaches 30 events, older events are erased to make room for newer ones. Note: There is a shortcut for quick access to the Event Log report. From the Welcome banner, press Reset (Pause/Reset on tread consoles) for five seconds. If there are no events, the words STUCK KEY appear and then the console returns to the Welcome banner.
20 Operating and Maintaining the P20 Console Event Number Description of Event 22 No motor pulses at start up 23 Motor pulses missing after start up 24 Reduce speed requested, speed is not reducing 26 Motor pulse width incorrect 27 Too much drive motor current 28 Temperature too high 29 Excessive AC input current 30 Communications event lower board to upper board 31 Incorrect Communications event upper board to lower board 32 Communication event upper board to lower board 33 Incorre
21 Setting Up the Console Lower Software Displays the software version (part number) of the motor drive unit. U-Base Software Displays the software version and part number of the upper unit application software. U-Boot Software Displays the software version and part number of the upper boot loader software.
22 Operating and Maintaining the P20 Console To view the Club Settings menu: 1. Press the following keys in the order presented. Reset (Pause/Reset on tread consoles) Enter Input Up Enter Programs Enter Input Up Enter Note: Only two seconds are allowed between keypresses. If a key is not pressed, the console display returns to the Welcome banner. 2. Press Up or Down to navigate the menu. 3. Press GO to select a test. 4.
23 Setting Up the Console Max Resistance (Bike, AMT) Select the maximum resistance that a user can program while using the equipment. Max Workout Time Set a maximum workout time per session. Choose a time limit between 1 and 90 minutes, or select No Limit if you do not want to set a workout time limit. Default Workout Time When set to ON, the default workout time will be 30 minutes. When set to OFF, program times will be the value in the max workout time setting. Unit of Measure Select U.S.
24 Operating and Maintaining the P20 Console Safety Code (Treadmill) The Safety Code feature prevents use of the treadmill until a password is entered. Select Enable to use this feature and press the following keys in the order presented. Programs Enter Input Down Input Up When the safety code is enabled, the display will be in the Welcome state until a key is pressed. If a key is pressed, the word PASSWORD? appears in the display.
25 Setting Up the Console Equipment Value Default Value All Unit of U.S. measurement All Model number Dependent on product All Time meter 0 hours All Event log 0 entries All Odometer 0 units All Cool down 5 minutes All Data entry inactivity time out 30 seconds All Time count up 00:00 minutes All Time count down 30:00 minutes All Course segments Value Range Value Change Increments 1-5 minutes 1 minute Entered time/20 if less than 20 minute workout.
26 Operating and Maintaining the P20 Console Equipment Value Default Value Treadmill Quick Start course segment 1 minute Treadmill Max incline 15 percent 0 - 15 incline percent 0.
Chapter 3 Introducing Users to the P20 Console CAUTION: Before beginning any fitness program, see your physician for a thorough physical examination. Seek advice from your physician to learn the target heart rate appropriate for your fitness level. The P20 console offers an easy-to-follow display and multiple programs to help people meet their exercise needs.
28 Operating and Maintaining the P20 Console To use the touch heart rate feature, place the palm of your hands directly on the metal heart rate sensors on the equipment’s handlebars. To ensure a more accurate heart rate readout, make sure you follow these tips: Both hands must grip the sensors for your heart rate to register. It takes a number of consecutive heart beats (15-20 seconds) for your heart rate to register. When gripping the sensors, do not grip tightly. Keep a loose, cupping hold.
Introducing Users to the P20 Console 29 Using a Chest Strap Transmitter WARNING Signals used by the Chest Strap Transmitter (or heart rate strap) may interfere with pacemakers or other implanted devices. Consult your physician and the manufacturers of your Chest Strap Transmitter and implanted device before using a Chest Strap Transmitter. Wearing a chest strap transmitter during your workout provides steady heart rate information.
30 Operating and Maintaining the P20 Console Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Presses down on the red Slows to a stop STOP button Shows that the exercise workout is paused Pulls on the lanyard Slows to a stop attached to the safety clip and trips the restart switch Shows the words PUSH TO RESET SWITCH and an arrow pointing to the Restart switch The restart s
Introducing Users to the P20 Console 31 If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about the current workout is deleted. 3. Start the workout from the beginning, reducing the time as needed to account for the amount of exercise that has been completed.
32 Operating and Maintaining the P20 Console If no user is detected after an additional 30 seconds, the console displays the message NO USER DETECTED, STOPPING IN 10 SECONDS as notification of the pending stop. During the display of this message, a ten second countdown begins. If a user does not override the countdown, the belt comes to a gradual stop after the countdown is complete. Note: Users weighing more than 90 pounds (41 kg) are detected within the speed and position limits of the feature.
Chapter 4 Starting a Workout CAUTION: If you are using a treadmill, be sure to attach the security clip to your clothing before starting your workout. The equipment is in the Welcome state when the words PRESS GO OR PROGRAMS TO START scroll across the scrolling text display area and the word WELCOME scrolls on the upper text display. Press Reset (Pause/Reset on tread consoles) to display the Welcome screen. From the Welcome screen, there are two ways to begin a workout: Press GO (Quick Start™ method).
34 Operating and Maintaining the P20 Console Starting a Preset Programmed Workout Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. The P20 includes the following preset programs: Manual Interval 1-1 Interval 1-2 Weight Loss Basic Heart Rate Control Hill Climb Cross Country Random Aerobic To begin using a program: 1. On the Welcome screen, press Programs. 2.
35 Starting a Workout To enter personal data: 1. On the Welcome screen, press Programs, then Enter. 2. Press the Input keys to change the default value. 3. Press Enter. The weight input screen displays. Press the Input keys to change the default value. 4. Press Enter. The age input screen displays. Press the Input keys to change the default value. 5. Press GO or Enter to begin your workout. The equipment counts down and 1, 2, 3 display on the screen.
36 Operating and Maintaining the P20 Console Paused (Externally Powered Equipment) When you interrupt your workout, the words WORKOUT PAUSED - PRESS GO TO CONTINUE scroll across the text display. The accumulated metrics (Time, Calories, Distance, and Average Speed) hold their current values and do not change. To restart the program, press GO. If the equipment remains inactive for more than the maximum pause time, it displays the Summary screen with your workout metrics.
37 Starting a Workout Understanding Metrics Three different types of metrics are captured during a workout.
38 Operating and Maintaining the P20 Console
Chapter 5 Programs Preset workouts are a great way to tailor your workouts to your fitness goals, stay challenged, and add variety to your sessions. In the following figures, the elevated areas show the work expenditure for each preset program. Manual In this program, resistance and speed changes are completely under your control. The profile is initially a flat line. Any increase or decrease made in one program segment will increase or decrease all remaining portions by the same amount.
40 Operating and Maintaining the P20 Console Interval 1-1 and Interval 1-2 The Interval programs are primarily for conditioning your cardiovascular system. These programs are designed to raise and lower your heart rate in a repeating fashion for a user-defined period of time by alternating rest and work intervals. Program intensity is adjustable. Figure 9: Interval 1-1 Figure 10: 1-2 Interval Weight Loss The program time is fixed at 28 minutes.
41 Programs Basic Heart Rate Control This program computes your target heart rate based on the calculation, 60% of 220 minus your age. The equipment adjusts resistance and/or incline to maintain your target heart rate while you work out. When a heart rate signal is not received, a heart shape with a question mark appears in the upper text display. Recheck your hand grip on the handheld sensors or the placement of your chest strap.
42 Operating and Maintaining the P20 Console Cross Country The purpose of the preset program is to simulate an outdoor running experience. In this case, you can change the overall profile or intensity of the program (resistance) at any time; however, you cannot change the shape of the preset "hills" and "valleys" you see depicted on the display. Figure 14: Cross Country Random Every time this program is selected, a different program profile appears.
Chapter 6 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals suggested. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks. If the equipment uses an optional power adapter, disconnect the adapter.
44 Notes: Operating and Maintaining the P20 Console
Operating and Maintaining the P20 Console Precor Incorporated 20031 142nd Avenue NE P.O.
Assembling and Maintaining TRM 800-Series Treadmills Precor Incorporated 20031 142nd Avenue NE P.O.
Edition Information ASSEMBLING AND MAINTAINING TRM 800-SERIES TREADMILLS P/N 300713-341 rev G Copyright © February 2011 Precor Incorporated. All rights reserved. Specifications subject to change without notice. Trademark Note Precor, AMT, and EFX are registered trademarks and Preva is a trademark of Precor Incorporated. Other names in this document may be the trademarks or registered trademarks of their respective owners.
Important Safety Instructions Read the following precautions thoroughly before you begin assembly, and save them afterward for future reference. Safety Precautions Always follow basic safety precautions when using this equipment to reduce the chance of injury, fire, or damage. Other sections in this manual provide more details of safety features. Be sure to read these sections and observe all safety notices.
4 Assembling and Maintaining TRM 800-Series Treadmills Use the power adapter provided with the equipment. Plug the power adapter into an appropriate, grounded power outlet as marked on the equipment. Care should be taken when mounting or dismounting the equipment. Read, understand, and test the emergency stop procedures before use. Keep the power cord or optional power adapter and plug away from heated surfaces.
Important Safety Instructions 5 When using the treadmill, always attach the safety clip to your clothing before beginning your workout. Failure to use the safety clip may pose a greater risk of injury in the event of a fall. Also, verify that the running belts on treadmills are clean and running smoothly. Do not allow runners over 350 pounds (160 kg) or walkers over 500 pounds (225 kg) to use the treadmill.
6 Assembling and Maintaining TRM 800-Series Treadmills Educating Users Take time to educate users about the Important Safety Instructions found in both the User Reference Manual and Product Owner’s Manual. Explain to your club or facility patrons that they should observe the following precautions: Hold onto a stationary handrail or handlebar while assuming the starting position on the equipment. Face the console at all times.
Important Safety Instructions 7 Product Recycling and Disposal This equipment must be recycled or discarded according to applicable local and national regulations. Product labels, in accordance with European Directive 2002/96/EC concerning waste electrical and electronic equipment (WEEE), determine the framework for the return and recycling of used equipment as applicable throughout the European Union.
8 Assembling and Maintaining TRM 800-Series Treadmills Radio Frequency Interference (RFI) The RFID module conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Important Safety Instructions European Applications CE compliance is claimed to the following directives: 1999/5/EC R&TTE Directive 2006/95/EC LVD Directive 2002/95/EC RoHS Directive Directive compliance has been verified to the following standards: EN 55022 EN 300 330-1 V1.5.1 EN 300 330-2 V1.3.1 EN 301 489-3 V1.4.1 EN 301 489-1 V1.8.
10 Assembling and Maintaining TRM 800-Series Treadmills Radio Frequency Interference (RFI) This Precor exercise equipment conforms to the following national standards defining acceptable limits for radio frequency interference (RFI). Federal Communications Commission, Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
11 Important Safety Instructions Treadmill Grounding Instructions The treadmill must be grounded. If the equipment malfunctions or breaks down, grounding draws off electric current and reduces the risk of electric shock. The power cord on the treadmill is equipped with a grounding conductor and a three-pin grounding plug. This plug must be inserted into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
12 Assembling and Maintaining TRM 800-Series Treadmills Important: An individual branch circuit provides a hot conductor and neutral conductor to a receptacle. The conductors must not be looped, "daisy-chained", or connected to any other conductors. The circuit must be grounded according to NEC guidelines or local region electric codes.
Table of Contents Important Safety Instructions ................................................... 3 Safety Precautions .................................................................................3 Safety Code ............................................................................................ 5 Educating Users .................................................................................... 6 Hazardous Materials and Proper Disposal ....................................
14 Assembling and Maintaining TRM 800-Series Treadmills Maintenance ............................................................................ 45 Daily Cleaning ..................................................................................... 45 Daily Inspection .................................................................................. 46 Weekly Maintenance ........................................................................ 47 Monthly Maintenance ........................................
Chapter 1 Assembling the Treadmill Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment). These descriptions may not match the names of certain parts in the parts list, because such parts are named relative to the back of the equipment. WARNING You will need assistance to assemble this unit.
16 Assembling and Maintaining TRM 800-Series Treadmills 5. Remove the shipping fasteners from the front panel using a ¹₄-inch hex key and a ¹⁄₂–inch box-end wrench. 6. Remove any tape or wire ties securing the console cable to the side of the unit.
17 Assembling the Treadmill Hardware Kit (not to scale) The hardware kit shipped with this equipment contains the fasteners and other hardware components shown in the following table. Before you begin assembly, make sure that your hardware kit is complete. If not, please contact Precor Customer Support.
18 Assembling and Maintaining TRM 800-Series Treadmills Unpacking the Cables To connect the console to the base unit, you may need up to five cables, as follows: Ethernet (P80 only) Television (P80 only) Power (P80 only) Base unit data Automatic stop sensor (Auto Stop™) The first three of these cables are shipped with the P80 console. The remaining two are shipped inside the treadmill fairing. To unpack the cables: 1. Open the box containing the P80 console.
19 Assembling the Treadmill 3. Remove the seven screws holding the back cover in place. Snap the back cover loose and set it aside, along with the seven screws. Figure 4: Removal and replacement of the rear fairing cover 4. Remove the two ends of the base unit data cable from the left arm of the fairing (position 1 in the following illustration). Route the shorter of the two cable ends into the fairing and extend the long end outward.
20 Assembling and Maintaining TRM 800-Series Treadmills 6. Remove any tape or ties that secure the cables, then unwind them and remove any kinks. Gather the cables into a single bundle (referred to later as the cable assembly). Note: Arranging the cables so that the connectors are slightly staggered at the bottom end (but still within one inch or three centimeters overall) can help when feeding the cable assembly through narrow openings in the frame.
21 Assembling the Treadmill 3. Secure the right-hand upright support to the side bracket using four socket head screws, four black washers, and two locknuts. Partially tighten the fasteners. Figure 7: Upright support attachment, right side 4. Using the fabric connectors provided, attach the power supply to the right-hand side of the front crossmember on the treadmill base. (The gray rectangle in the following illustration shows where you should mount the power supply.) 5.
22 Assembling and Maintaining TRM 800-Series Treadmills To thread cables through the frame: 1. Feed the cable assembly downward through the left-hand upright support and out through the opening in the lower end of the support. Drape the remaining cable over the front of the support and tape it into place if necessary to secure it temporarily. 2. Feed the cable assembly through the grommet in the left-hand side bracket of the base frame.
23 Assembling the Treadmill Component Appearance Television cable Round with black insulation Console power cable Dual leads with red and black insulation Auto Stop sensor cable Round with black insulation Power supply Rectangular, black, 5" x 2¹₄" x 1¹₄" Lower connection point CAUTION: Be careful not to cut or pinch any wires during the following step. 3. Place the left-hand upright support into the base frame side bracket. 4.
24 Assembling and Maintaining TRM 800-Series Treadmills 7. Route the cable assembly through the cable guides in the fairing, then wrap the guides around the cable assembly to secure it. Push any extra cable into the upright support. Note: In the following step, use the zinc-finish buttonhead screws and flat washers from the hardware kit. Important: Do not wrench-tighten the fasteners in the following step until the unit has been fully assembled. Make sure the fasteners do not pinch any cables.
Assembling the Treadmill 25 Completing Assembly After the upright supports and the fairing are in place, replace the hood on the treadmill base and finish securing the fasteners. CAUTION: Be aware of the handrail extensions when you are working around the front of the unit. It is easy to bump your head or sustain other injuries if you ignore the location of the handrail extensions. To secure the fasteners: 1.
26 Assembling and Maintaining TRM 800-Series Treadmills Note: Using a hex wrench, reach through the openings in the outer sides of the hood to tighten the side screws. Figure 11: Hood and fastener placement Attaching the Power Cord Clips This treadmill includes a set of clips that hold the power cord away from the incline lift movement and other potential sources of wear and damage. Use these clips to secure the power cord to the base frame beneath the hood.
27 Assembling the Treadmill 2. Insert the serrated portion of the clip into the hole located under the front of the unit on either side of the power switch. Figure 13: Power cord placement under front of treadmill 3. Place the clips along the length of the power cord as needed while you direct the cord to the power outlet. The holes, found in the frame beneath the side rail, are spaced 12 inches (31 cm) apart along the length of the side rail.
28 Assembling and Maintaining TRM 800-Series Treadmills Leveling the Unit The treadmill deck must be absolutely level from side to side to keep the belt in alignment and ensure proper operation. If the load is not equally distributed across the treadmill deck, users may feel excessive vibration or observe it at the console. You must make sure the deck is level before allowing anyone to use the treadmill.
29 Assembling the Treadmill 4. Adjust the rear feet as needed. Figure 16: Leveling foot adjustment 5. Repeat steps 1 through 4 until the treadmill is level. 6. If necessary, adjust the rear feet so that the user’s weight is distributed evenly on the treadmill. Plugging In the Power Cord CAUTION: Use the supplied power cord. Do not remove or otherwise bypass the 3-prong plug with an adapter to use a non-grounded outlet.
30 Assembling and Maintaining TRM 800-Series Treadmills
Chapter 2 Installing the Console To make installation easier, all Precor Experience Series consoles use the same mounting hardware and connector locations whenever possible. The installation sequence for any of them is as follows: Threading the cable assembly Connecting cables Completing the installation (tightening the mounting screws and attaching the back cover) The following sections describe how to perform these tasks.
32 Assembling and Maintaining TRM 800-Series Treadmills Important: Before you begin the following procedure, remove the rear cover from the control console. To remove the cover, use your fingernails to pry the lower edge loose, then swing the cover up and out as shown in the following illustration. Figure 17: Removing the access cover from the P80 console To thread the cable assembly: 1.
33 Installing the Console 4. Tilt the console forward until it stops. Use one hand to steady the console in this position, or ask your assistant to do so. 5. Using a #2 Phillips screwdriver, remove the two #8-32 x ¹₂” pan-head machine screws securing the upper back cover of the fairing, as shown in the previous figure. Set the cover and the screws aside.
34 Assembling and Maintaining TRM 800-Series Treadmills Cable Connector Type TV in F-type coaxial Power Two-contact plug, polarized and latched Data from base unit Eight-contact modular, on flat gray cable Heart rate sensors Four-contact strip, keyed Safety key (treadmills only) Six-contact strip, keyed CSAFE Eight-contact modular, on flat gray cable Auto Stop sensor (treadmills only) Four-contact strip, keyed Circuit Connector Location To simplify installation and maintenance, route and
Installing the Console 35 The following illustration shows how the cable is positioned once it is installed. Figure 20: Connecting the television cable Connecting the Ethernet and Base Unit Data Cables Both the Ethernet and base unit data cables pass through the cutaway opening at the upper right corner of the back plate and connect to nearby modular jacks in the console. Because of this, it is important to exercise caution when connecting the cables.
36 Assembling and Maintaining TRM 800-Series Treadmills Connecting the Heart Rate Sensor Cable The heart rate sensor cable passes through the cutaway opening at the upper left corner of the back plate, then down to the small circuit board at the lower left of the console. The following illustration shows how the cable should look once it is installed.
Installing the Console 37 Completing the Console Installation (P80) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installation: 1. Feed extra cable back into the neck tube. 2.
38 Assembling and Maintaining TRM 800-Series Treadmills Threading the Cable Assembly (P30 and P20) Earlier in the installation, you threaded the necessary cables through the frame of the base unit and out the passthrough opening in the console mount. As you line up the back plate on the console with the console mount, you must make sure that the cable assembly passes correctly through the openings in both components.
39 Installing the Console Connecting Cables (P30) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and connectors. Figure 25: Cable connections, P30 console Table 3.
40 Assembling and Maintaining TRM 800-Series Treadmills Connecting Cables (P20) After the console has been seated, separate the individual cables out of the end of the cable assembly and attach them to the appropriate circuit connectors inside the console. Refer to the following diagram and table to identify the cables and connectors. Figure 26: Cable connections, P20 console Table 4.
Installing the Console 41 Completing the Console Installation (P30 and P20) Before you complete the final installation steps, double-check the connections you have made. Make sure that all cables are fully and securely connected, and that any unneeded cables are tied back properly. To complete the installation: 1. Feed extra cable back into the neck tube. 2.
42 Assembling and Maintaining TRM 800-Series Treadmills Reassembling the Treadmill Fairing After the console is in place, reattach the two cover panels of the treadmill fairing. Important: In the following procedure, do not allow the fasteners to break or pinch any cables. To reassemble the fairing: 1. Verify that the cable assembly is secure inside the cable clips and that the ferrite bead on the base unit data cable is tied securely into place in the left arm of the treadmill. 2.
Installing the Console 43 Verifying That the Heart Rate Display Is Operational To verify that the heart rate display is operational: 1. Begin exercising on the equipment. 2. Grasp both touch-sensitive handlebars. Note: The heart rate is read within ten seconds. During that time, the heart on the display flashes. 3. Look at the HEART RATE display. After a few seconds, a number appears indicating your heart rate. 4.
44 Assembling and Maintaining TRM 800-Series Treadmills
Chapter 3 Maintenance To keep the equipment functioning properly, perform the minor maintenance tasks in this section at the intervals shown on the maintenance checklist. Failure to maintain the equipment as described in this section could void the Precor Limited Warranty. DANGER To reduce the risk of electrical shock, always disconnect the equipment from its power source before cleaning it or performing any maintenance tasks.
46 Assembling and Maintaining TRM 800-Series Treadmills Alternatively, you can clean the equipment with Athletix fitness equipment cleaning wipes (for more information, visit www.athletixproducts.com) CAUTION: Read and follow the manufacturer’s instructions, particularly dilution instructions, before using any cleaner on Precor fitness equipment.
47 Maintenance Weekly Maintenance Perform the following maintenance tasks every week: 1. 2. 3. 4. 5. 6. Elevate the tread to maximum incline, then turn off the power switch or circuit breaker and unplug the unit from the wall outlet. Clean the floor under the equipment using a vacuum cleaner or a damp mop. When the floor is completely dry, reconnect the power and return the treadmill to the level position.
48 Assembling and Maintaining TRM 800-Series Treadmills 5. Check the belt tension of the step-up and drive belts. 6. Clean and lubricate the lift motor screw with an approved grease such as SuperLube® with Teflon® or Mobil 1® synthetic grease (adjustable-ramp models only). 7. Check all fasteners for proper tightness and torque. 8. Replace all covers. 9. Verify that the unit sits squarely on the floor. All of its feet should be touching the floor and the unit should not rock or wobble when in use.
49 Maintenance If the belt tracks off center ... Then loosen ... To the left The right adjusting bolt To the right The left adjusting bolt 3. Recheck the belt position as described under Checking the Alignment of the Running Belt. Note: If slippage occurs, tighten both adjusting bolts evenly until it stops. Do not overtighten the belt. Checking the Alignment of the Running Belt Proper alignment allows the belt to remain centered and ensures smooth operation.
50 Assembling and Maintaining TRM 800-Series Treadmills 6. Observe the belt from the rear of the treadmill for a few minutes. The belt should remain centered along the running bed. If it drifts off center, adjust it. Refer to Treadmill: Adjusting the Running Belt. Important: Failure to align the belt may cause the belt to tear or fray, which is not covered by the Precor Limited Warranty. 7. Press the red STOP button to stop the belt. 8. Turn the treadmill OFF.
51 Maintenance Long-Term Storage If you do not expect anyone to use the equipment for a long time, perform the following tasks to prepare it for storage: Turn it OFF. If it has a power cord, disconnect the cord. If it has an optional power adapter, connect the adapter to prevent damage to the internal battery. Position it so that it will not become damaged and will not interfere with people or other equipment.
52 Assembling and Maintaining TRM 800-Series Treadmills
Chapter 4 Treadmill Safety Features Before allowing users on Precor equipment, review the Important Safety Instructions in this manual. You should also teach your patrons how to use the equipment safely, according to the guidelines on. Entering the Safety Code When the equipment is shipped from the factory, safety code protection is not active. After you have activated the safety code, you must inform your patrons that the equipment requests a safety code to prevent unauthorized use.
54 Assembling and Maintaining TRM 800-Series Treadmills Using the Treadmill Safety Clip The treadmill is equipped with two different stop functions, which behave as follows: If the user … Then the treadmill belt … And the console … Presses down on the red Slows to a STOP button stop Shows that the exercise workout is paused Slows to a Pulls on the lanyard stop attached to the safety clip and trips the restart switch Shows the words PUSH TO RESET SWITCH and an arrow pointing to the Restart switch Th
Treadmill Safety Features 55 If the restart switch trips during exercise, perform the following steps: 1. Reattach the safety clip if necessary. 2. Press the restart switch down until it clicks, returning it to its normal position. Note: If the restart switch trips, all information about the current workout is deleted. 3. Start the workout from the beginning, reducing the time as needed to account for the amount of exercise that has been completed.
56 Assembling and Maintaining TRM 800-Series Treadmills
Chapter 5 Commercial Cardiovascular Equipment Limited Warranty PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND CONDITIONS. Limited Warranty. Precor Incorporated warrants all new Precor products to be free from defects in materials and manufacture for the warranty periods set forth below.
58 Assembling and Maintaining TRM 800-Series Treadmills Options / Accessories Many options or accessories have components that are connected internally or mounted inside the electronic console. The following guidelines determine the warranty for these components. If the internal components are installed by the factory or by an authorized dealer as part of the original sale and delivery, they have a warranty that is identical to the warranty of the equipment in which they are connected or mounted.
Commercial Cardiovascular Equipment Limited Warranty 59 This Limited Warranty shall not apply to: 1. Software version upgrades. 2. Software defects that do not materially and negatively affect the normal performance of the product under normal conditions of use. 3.
60 Assembling and Maintaining TRM 800-Series Treadmills EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.
Assembling and Maintaining TRM 800-Series Treadmills Precor Incorporated 20031 142nd Avenue NE P.O.
