Product manual 4179 Universal AC / DC transmitter PERFORMANCE MADE SMARTER T E M P E R AT U R E | I . S . I N T E R FA C E S | CO M M U N I C AT I O N I N T E R FA C E S | M U LT I F U N C T I O N A L | I S O L AT I O N | D I S P L AY No. 4179V10 0 - UK From serial no.
6 Product Pillars to meet your every need Individually outstanding, unrivalled in combination With our innovative, patented technologies, we make signal conditioning smarter and simpler. Our portfolio is composed of six product areas, where we offer a wide range of analog and digital devices covering over a thousand applications in industrial and factory automation.
Universal AC / DC transmitter 4179 Table of contents Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbol identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety instructions . . . . . . . . . . . . . . . . . . . . . . .
Warning GENERAL This device is designed for connection to hazardous electric voltages. Ignoring this warning can result in severe personal injury or mechanical damage. To avoid the risk of electric shock and fire, the safety instructions of this guide must be observed and the guidelines followed. The specifications must not be exceeded, and the device must only be applied as described in the following. Prior to the commissioning of the device, this installation guide must be examined carefully.
Safety instructions Definitions Hazardous voltages have been defined as the ranges: 75 to 1500 Volt DC, and 50 to 1000 Volt AC. Technicians are qualified persons educated or trained to mount, operate, and also trouble-shoot technically correct and in accordance with safety regulations. Operators, being familiar with the contents of this manual, adjust and operate the knobs or potentiometers during normal operation.
How to demount system 4000 Picture 1: The device is detached from the DIN rail by moving the bottom lock down. When front LED flashes red or 4511/4501 display shows AO.ER The 4179 is designed with a high safety level. Therefore, the device continuously measures the output current. If "S4-20" is selected during configuration, and output current drops to 0 mA, the 4511/4501 display will indicate "AO.ER" and the front LED will turn red. (A 0 mA output can be caused by an open output loop).
Universal AC/DC transmitter 4179 • Measures AC current and voltage signals and converts these into uni-/bipolar DC current and voltage signals ∼ • Outputs passive or active current signals • Programming, process monitoring and diagnostics via 4511 / 4501 • Response time < 0.75 s and excellent accuracy better than 0.3% • Universally powered by 21.6…253 VAC / 19.2...300 VDC Application • The 0... 5 AAC range makes it possible to accurately measure a typical current transformer. • The 0...
Applications Input signals: Current Voltage 44 43 (N) 42 (N) 41 Output signals: Current & voltage 12 14 + + 10 V 10 V } (±) 1V 13 + 11 Power connection: 21.6...253 VAC or 19.2...
PR 4511/4501 display / programming front Functionality The simple and easily understandable menu structure and the explanatory help texts guide you effortlessly and automatically through the configuration steps, thus making the product very easy to use. Functions and configuration options are described in the section ”Configuration / operating the function keys”. Application • Communications interface for modification of operational parameters in 4179.
Order 4179 = Universal AC / DC transmitter Accessories 4501 = Display / programming front 4511 = Communication enabler Electrical specifications Environmental conditions: Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Calibration temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accuracy, the greater of general and basic values: General values Input type Absolute accuracy Temperature coefficient All ≤ ±0.3% of span* ≤ ±0.01% of span* / °C Basic values Input type Basic accuracy Temperature coefficient Current 1.5 mA 50 µA/ °C Voltage 1.5 mVAC 50 µVAC /°C EMC - immunity influence . . . . . . . . . . . . . . . . . . . . . . . . < ±0.5% of span* Extended EMC immunity: NAMUR NE 21, A criterion, burst . . . . . . . . . . . . . . . .
Passive 2-wire mA: Programmable ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0...20 and 4...20 mA Direct or Inverted action V-curve function, 100-0-100% . . . . . . . . . . . . . . . . . . . . . . . . . . 20-0-20 mA External 2-wire loop supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5...
Configurable input error indication and input limits Configurable input error detection To increase system safety and integrity, users can program a high and low input error detection level. Input signals outside the selected error indication levels will cause the output of the device to go to the programmed error state. The error is indicated in display line 1 as IN.ER and at the same time the backlight flashes.
Output limits and error indications – current output: Input limit check disabled Input limit check Low and / or High enabled Output span Output limit Output limit Output limit Output limit low high low high Output error Output error Output error Output error indication, indication, indication, indication, NONE ZERO DOWN UP 4...20 mA 0 mA 23 mA 3.8 mA 20.5 mA 23 mA 3.5 mA 0 mA No error indication 0...20 mA 0 mA 23 mA 0 mA 20.5 mA 23 mA 0 mA 0 mA No error indication ±10 mA -11.5 mA 11.
4511/4501 display readout of input error detection and signal ”outside range” Configurable input error detection - readout (IN.ER): Input Range Readout Limit CURR All IN.ER See table on page 14 VOLT All IN.ER See table on page 14 Display readout below min. / above max. (-1999, 9999): Input Range All All Readout Limit -1999 Display readout <-1999 9999 Display readout >9999 Readout at hardware error Error search Readout Cause Check measurement of analog output AO.
Connections Supply 31 32 33 Inputs: Current Voltage 41 42 43 44 41 42 43 44 Outputs: Current 2-wire transmitter Voltage, 1 V Voltage, 10 V 11 12 13 14 11 12 13 14 11 12 13 14 11 12 13 14 - mA + (±) 16 mA - + - V (±) 4179V100-UK + - V (±) +
4179V100-UK Voltage input Current input 41 (N) 42 43 44 A/D HW Watchdog Green 4179 CPU Red D /A 50 500 1V I- / V- 11 10 V I+ A I+V V V 21.6...253 VAC or 19.2...300 VDC V Supply N.C.
Configuration / operating the function keys Documentation for routing diagram. In general When configuring the 4179, you will be guided through all parameters and you can choose the settings which fit the application. For each menu there is a scrolling help text which is automatically shown in line 3 on the display.
Language (LANG): In the menu ”LANG” you can choose between 7 different language versions of help texts that will appear in the menu. You can choose between UK, DE, FR, IT, ES, SE and DK. Output function (OFUN): Here the output characteristics can be set to either Direct (DIR) or Inverted (INV) function. Output type and range are set in the normal programming menu. If the selected output range is starting at zero, V-curved output function (VFUN) can also be selected.
Routing diagram If no key is activated for 1 minute, the display will return to the default state 1.0 without saving configuration changes. 1 Increase value / choose next parameter 2 Decrease value / choose previous parameter 3 Save the chosen value and proceed to the next menu Hold 3 Back to previous menu / return to menu 1.0 without saving. 0-5 0-2.5 0-1 0-0.5 CUST 12 Power up 0000 9999 12 40.0 % 10.4 mA *0 3 0000 PASSW. Txt 1 NO YES 12 Correct No NO 3 CURR VOLT 12 3 ADV.
blank : : % @F @C 12 111.1 11.11 1.111 1111 12 9999 -9999 12 9999 -9999 12 UNIT 1.111 0.00 5.000 DEC.P Txt 7 DISP.LO Txt 8 DISP.HI Txt 9 A RMS Txt 6 -/+20 -/+10 S4-20 4-20 0-20 12 CURR VOLT 12 3 CURR CURR 3 ANA.OUT Txt 10 4-20 PASS ACTI 12 ACTI 3 O.RANGE Txt 11 3 OUT.MOD Txt 13 *3 *2 -/+10 1-5 -/+5 0-5 -/+1 0.2-1 2-10 0-1 0-10 12 VOLT 0-10 3 3 O.
YES NO 12 NO 0.00 0.00 12 3 ILIM.L Txt 50 VRMS Txt 51 NO *15 22 0.00 UP ZERO DOWN NONE 12 UP YES NO 12 3 OUT.ERR Txt 54 YES VRMS Txt 53 NO *16 230 3 ILIM.H Txt 52 *15 Limits are dependent on input type and the selected input range: High limit: 'Minimum input' Low limit, CURR: 0 AAC Low limit, VOLT: 0 VAC 300 230 12 UP ZERO DOWN NONE 12 UP 60.0 0.0 12 3 OUT.ERR Txt 54 *16 Limits are dependent on input type and the selected input range: Low limit: 'Maximum input' High limit, CURR: 5.
Routing diagram, advanced settings (ADV.SET) MEM, DISP, CAL, SIM, PASS, LANG, OFUN 12 SAVE LOAD 12 MEM SAVE 3 SETUP Txt 15/1 3 MEMORY Txt 16 9 0 12 DISP CAL 3 3 SETUP Txt 15/2 A.OUT LINE 3 Txt 20 YES NO 12 5.000 0.000 12 YES NO 12 5.000 0.000 12 NO 3 3 NO 3 3 NO 3 5.000 *5 YES NO 12 3 A RMS Txt 24 CAL.HI Txt 23 NO NO 2.500 YES NO 12 3 USE.CAL Txt 25 *5 To default state 1.0 3 A RMS Txt 27 NO NO 3 3 5.000 0.000 12 ENA.SIM Txt 26 3 0.000 A RMS Txt 22 CAL.
Help text overview [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20] [21] [22] [23] [24] [25] [26] 24 Set correct password Enter advanced setup menu? Select current input Select voltage input Select 0...5 A input range Select 0...2.5 A input range Select 0...1 A input range Select 0...0.5 A input range Select custom current input range Select 0...230 V input range Select 0...120 V input range Select 0...2.83 V input range Select 0...1 V input range Select 0...
Document history The following list provides notes concerning revisions of this document. Rev.
We are near you, all over the world Our trusted red boxes are supported wherever you are All our devices are backed by expert service and a 5-year warranty. With each product you purchase, you receive personal technical support and guidance, day-to-day delivery, repair without charge within the warranty period and easily accessible documentation. We are headquartered in Denmark, and have offices and authorized partners the world over. We are a local business with a global reach.
Benefit today from PERFORMANCE MADE SMARTER PR electronics is the leading technology company specialized in making industrial process control safer, more reliable and more efficient. Since 1974, we have been dedicated to perfecting our core competence of innovating high precision technology with low power consumption. This dedication continues to set new standards for products communicating, monitoring and connecting our customers’ process measurement points to their process control systems.
