CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS P4263T Universal Low Profile Tilt Mount for 42” to 63” Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone: (001).714.632.7100 Fax: (001).714.632.
P4263T Contents Weight Limit................................................................................................................................................................................... 2 Warning Statements...................................................................................................................................................................... 2 Installation Tools................................................................................................
P4263T Installation Tools The following tools may be required depending upon your particular installation. They are not included. Electronic Stud Finder ¼˝ Drill Bit for Wood Stud 7/16˝ Drill Bit for Steel Stud* /16˝ Concrete Drill Bit** Hand Held Drill 5 2 1 Pencil Level Protective Eyewear Socket Wrench Tape Measure ½˝ Socket Hammer** Phillips Tip Screwdriver M10 Socket* * Optional tools for steel stud installations. ** Optional tools for concrete installations.
P4263T Parts List (cont’d) Mounting Hardware M4 x 16mm Screw (Qty 6) M8 x 16mm Screw (Qty 6) M4 x 25mm Screw (Qty 6) M8 x 25mm Screw (Qty 6) M4 x 30mm Screw (Qty 6) M8 x 30mm Screw (Qty 6) M5 x 16mm Screw (Qty 6) M8 x 45mm Screw (Qty 6) M5 x 25mm Screw (Qty 6) M8 x 70mm Screw (Qty 4) M5 x 30mm Screw (Qty 6) M6 x 16mm Screw (Qty 6) M6 x 25mm Screw (Qty 6) M6 x 30mm Screw (Qty 6) M6 x 45mm Screw (Qty 6) Page 4 Visit the Premier Mounts website at http://www.premiermounts.
P4263T Features Leveling Screws Allows for leveling adjustments of the flat panel after mounting. Cable/Electrical Cut Out A large cut out on the wall plate allows for easy cable access and power distribution installations. Directional Mounting Arrow Directional Mounting Arrow lets you know which edge is up. Low Profile Design Holds the flat panel less than 2″ from the wall. Mounting Slots Allow for a variety of stud configurations and lateral shift adjustments when mounting your flat panel.
P4263T Installing the Wall Plate Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the top of the P4263T wall mount indicates which edge is the top. Mounting Safety Two people are recommended to for the installation of this mount. Determining the Mounting Surface If you will be installing your P4263T mount to wood studs, proceed to the “Wood Stud Installation” section.
P4263T Installing the Wall Plate (cont’d) Step 3 Drill a “pilot hole” in the center of the upper right mark using a ¼″ drill bit and power drill. Only use a ¼″ drill bit when drilling the pilot holes. Step 4 Place the wall plate against the wall and align it with ®® the pilot hole. Insert one (1) 5/16″ x 3″ lag bolt and one (1) 5/16″ washer into the upper right mounting hole and tighten using a socket wrench and ½″ socket. Do not overtighten the lag bolt. Step 5 Level the wall plate.
P4263T Installing the Wall Plate (cont’d) Step 7 Insert one (1) ®® /16″ x 3″ lag bolt and one (1) 5/16″ washer into each pilot hole Tighten all lag bolts using a socket wrench and ½″ socket. 5 Do not overtighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. Proceed to the “Installing the Mounting Bracket” section. Concrete Installation The supplied 5/16″ concrete wedge anchors must be used for concrete installation.
P4263T Installing the Wall Plate (cont’d) Step 3 Insert a concrete wedge anchor into each hole. ®® ¯¯ If necessary, lightly tap each concrete wedge anchor into place with a hammer. Remove the nuts and washers from all four (4) concrete wedge anchors. Replace the washers which you removed from the concrete wedge anchors with the 5/16″ washers shown in the parts list on Page 3. Step 4 Place the wall plate against the wall over the ®® threaded shafts of the concrete wedge anchors.
Installing the Wall Plate (cont’d) P4263T Step 2 Place the wall plate against the wall in the desired ®® ¯¯ °° ±± viewing location. Adjust the wall plate to match the locations of the steel studs. Level the wall plate. Use a pencil and mark 2 upper and 2 lower locations where you will be drilling holes for the steel stud anchors. Set the wall plate to one side in a safe location. Step 3 Use a power drill and ®® 7 /16″ drill bit to drill a hole at each of the marks.
P4263T Installing the Wall Plate (cont’d) Step 5 Align the wall plate over the steel stud anchor sleeves. ®® Insert a steel stud anchor screw and a / ″ washer into 5 ¯¯ X 16 each steel stud anchor sleeve. Use a Phillips screwdriver and tighten each steel stud anchor screw until it is just snug. X Do not overtighten the steel stud anchor screws. Do not use a power drill to tighten the steel stud anchor screws. Proceed to the “Installing the Mounting Bracket” section.
P4263T Installing the Mounting Bracket (cont’d) Universal Washer Installation Premier Mounts’ Universal Washers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat panels. M8 M5, M6 M4 Do not place excessive pressure on the back of the flat panel, as this may damage your flat panel. The Universal Washer must be installed between the head of the mounting screw and the mounting bracket as shown.
P4263T Installing the Mounting Bracket (cont’d) Attaching the Mounting Bracket to the Flat Panel This section presumes that you have read and understood these sections: ●● Selecting the Proper Mounting Hardware ●● Universal Washer Installation ●● Universal Spacer Installation Place your flat panel screen-side down on a soft, flat ®® ¯¯ °° surface. Identify the number and location of the thread inserts on the back of your flat panel.
Attaching the Flat Panel to the Wall Plate P4263T This section requires two people. Do not release your flat panel until you are certain that top and bottom hooks of both mounting brackets are securely seated on the upper and lower mounting rails of the wall panel. Raise the flat panel past the top and bottom mounting rails on the wall panel. ®® Slide the flat panel down slowly, keeping it close to the wall. ¯¯ Engage the top and bottom mounting brackets to the rails of the wall plate.
P4263T Tilt Adjustment Adjusting the Flat Panel Friction Tilt Angle Place one hand at the center top edge of the ®® ¯¯ flat panel. Place the other hand on the center bottom edge of the flat panel. Using the upper hand, gently pull the top of the flat panel towards you while the lower hand gently pushes the bottom of the flat panel away from you. Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the flat panel.
Technical Specifications P4263T All measurements are in inches [millimeters]. Page 16 Visit the Premier Mounts website at http://www.premiermounts.
P4263T Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
