INSTALLATION INSTRUCTIONS Short-Throw Projector Wall Mount Model: CPD10WALLARM NORTH AMERICA EUROPE AUSTRALIA AND OCEANIA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Swallow House, Shilton Industrial Estate, Shilton, Coventry, England CV79JY Phone: 1.800.368.9700 Fax: 1.800.832.
CPD10WALLARM Contents Weight Capacity. ........................................................................................................................................................ 2 Warning Statements. ................................................................................................................................................. 2 Installation Tools. .................................................................................................................................
CPD10WALLARM Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store.
CPD10WALLARM Determining the Installation Height Legend In order to determine the installation height and throw distance, the projector bracket must be mounted to the projector. Please refer to the Installation Instructions prior to performing the following steps. A- Distance from ground to the top of the screen/whiteboard (viewable area). Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the screen/whiteboard (B).
CPD10WALLARM Wood Stud Installation Step 1 THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION. Do NOT overtighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or damage to property. Use a stud finder to determine the exact center of wall studs in the vicinity of the wall plate. Step 2 Use a pencil to mark the first mounting point, just above your height mark (from the "Determining the Installation Height" section).
CPD10WALLARM Wood Stud Installation (cont'd) Step 5 Use four (4) 516˝ x 3” lag bolts and four (4) flat washers to mount the wall plate to the wooden studs. Use a ½” socket and socket wrench to finish this step. Do not overtighten the lag bolts. Lag Bolt and Flat Washer X Insert and gently tap the wall plate covers into place. Proceed to the "Removing the End Cover" section. ½˝ Socket and Wrench X Removing the End Cover Locate the end cover.
CPD10WALLARM Attaching the Projector Arm Step 1 Locate the mounting hook cutout on the top of the wall plate. Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts. Slowly lower and let the projector arm rest against the wall plate. If using the storage feature of the product, it may be easier to route any wiring at this time (please see the "Cable Management" section). Mounting Hook Cutout MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT.
CPD10WALLARM Extension Arm Installation Please see the Operator’s Manual to determine the correct throw distance (the distance from the projector to the screen). The throw distance must be determined prior to mounting the projector. Slide the extension arm into the open end of the CPD10WALLARM (the front of the mount). Adjust length so that the center of the adjustable mounting bracket matches the throw distance calibration.
CPD10WALLARM Adjustable Mounting Bracket Installation (cont.) Step 2 Secure and fingertighten two (2) M6 x 16mm security head screws. If the adjustable mounting bracket needs to be adjusted, the four (4) M6 x 12mm security screws may be loosened so that the bracket can be moved ±2˝. Fingertighten all hardware. Do not tighten the mounting hardware at this time. Proceed to the "Base Box Installation" section.
CPD10WALLARM Projector Bracket Installation Step 1 Invert the projector and place it on a soft, flat surface. Remove any foot levelers that might prevent bracket installation. Locate the mounting points on the projector. Place the bracket on the projector. Align the mount holes on the bracket with the mounting points on the projector. Projector shown is for example purposes only. Images not to scale. Step 2 Insert one (1) M4 x 10mm screw into each mounting point.
CPD10WALLARM Throw Distance Calculation Please review the Operator’s Manual that came packaged with your projector before attaching the upper mounting bracket. The correct throw distance (the distance from the projector to the screen) must be determined prior to mounting the projector. Refer to the projectors Users Manual to determine the distance from the lens to the front of the screen (X). Measure the distance from the front of the lens to the center of the projector (Y).
CPD10WALLARM Utilizing the Storage Feature Step 1 The storage feature may be used to store electronic components. There is an accessible door on each side of the storage enclosure. It may be securely held shut with the use of four (4) M5 x 8mm security head screws. It may be easiest to pre-wire all cables down the arm (or extension) at this time. Open the storage door that is located on the side of the wall plate. Place the electronic components inside the storage enclosure.
CPD10WALLARM Cable Management The cable access holes are located at the end of the short throw mount and on the wall plate. Route the cables through one end of the CPD10WALLARM and out the other end. Attach the end cover with an M5 x 8mm security head screw. CPD10WALLARM Electronic Components Cable Opening Cables Cable Opening Projector Connections Technical Specifications All measurements are in inches(mm). Installation Instructions Visit Premier Mounts website at http://www.mounts.
CPD10WALLARM Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.