CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Elliptical Ceiling Mount for 37” to 63” Flat Panels Model: ECM-3763Q NORTH AMERICA EUROPE 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations Phone: (001).714.632.7100 Fax: (001).714.632.
ECM-3763Q Contents Installation Tools. ...................................................................................................................................................... 3 Parts List................................................................................................................................................................... 3 Mounting Hardware. ............................................................................................................................
ECM-3763Q Installation Tools The following tools may be required, dependent upon your particular installation. These tools are not provided by Premier Mounts, but you can purchase them at your local hardware store. Tape Measure Protective Eye Wear Phillips Tip Screwdriver Pencil 10mm Wrench Ladder Parts List Your Premier Mounts product is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation.
ECM-3763Q Parts List (cont’d) Standard Hardware M4 x 16mm Phillips Head Screw (Qty 32) M4 x 25mm Phillips Head Screw (Qty 16) M5 x 12mm Phillips Head Screw (Qty 24) M5 x 16mm Phillips Head Screw (Qty 24) M5 x 20mm Phillips Head Screw (Qty 24) M5 x 25mm Phillips Head Screw (Qty 16) M5 x 50mm Phillips Head Screw (Qty 16) M6 x 12mm Phillips Head Screw (Qty 32) M6 x 20mm Phillips Head Screw (Qty 24) M6 x 30mm Phillips Head Screw (Qty 24) M8 x 20mm Phillips Head Screw (Qty 24) M8 x 25mm Phillips Head Scr
ECM-3763Q Features Decorative Cover Please refer to Page 11 for instructions on how to install the decorative covers. Quad Mount Please see Page 6 for installation instructions. 3LSH &RXSOHU Please see Page 6 for installation instructions. Elliptical Tilt Mount Please see Page 9 for installation procedures for the elliptical tilt mount. Mounting Bracket Arm Please see Page 10 for attachment instructions.
ECM-3763Q Installing the Ceiling Mount A 2” NPT threaded pipe must be firmly secured to the ceiling structure before performing the following steps. For more height flexibility, use Premier Mounts’ adjustable-height ceiling adapter (AST-2446) (sold separately). 2" NPT Pipe The Phillips set screw must be backed out in order for the NPT threaded pipe to attach to the threaded coupler. ➊ Align the ECM-3763Q threaded coupler with the threaded end of the NPT threaded pipe.
ECM-3763Q Selecting the Mounting Hardware Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded ® ¯ ° ± inserts found on the back of the flat panel. Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. Mark the straw or toothpick 1/8” above the depth of the threaded insert, as shown in Figure 1.
ECM-3763Q Griplate™ Washer Installation Premier Mounts’ Griplate™ Washers are designed to accommodate the various M4, M5, M6 and M8 hole sizes required by flat panels. Do not place excessive pressure on the back of the flat panel, as this may damage your flat panel. M8 M6 M5 M4 The Griplate™ Washer must be installed between the head of the mounting screw and the mounting bracket as shown.
ECM-3763Q Inserting the Hex Head Bolts Locate the two (2) upper mounting holes located on the back of the elliptical tilt mount. Attach two (2) M6 x 12mm hex head bolts and two (2) M6 split flat washers. Thread the hex bolts into the hole until there is a ¼˝ gap between the head of the hex head bolt and the mounting surface of the elliptical tilt mount. Repeat Steps 1 through 3 for all four of the elliptical tilt mounts. Do not completely tighten the hex head bolts at this time.
ECM-3763Q Attaching the Flat Panel Install the mount according to the instructions provided by Premier Mounts. Ensure all structural reinforcements have been made before attaching the flat panel to the ECM-3763Q. Do not release the flat panel until the mounting bracket arms are fully resting on the elliptical mounting bar. Raise the mounting bracket arms and the attached flat panel over the elliptical mounting bar of the ECM-3763Q )LJXUH .
ECM-3763Q Attaching Decorative Covers first Step 1 When attaching the decorative covers, verify the direction of the covers. The smaller mounting hole should be in position above the larger mounting hole. ➊ ➋ ➌ Insert and tighten an M6 x 25mm Pan Combo screw in the larger mounting hole of each mounting bracket arm. Place the first decorative cover over the first mounting bracket arm and push firmly into place. Repeat Step 1 for the next decorative cover.
ECM-3763Q Tilt Positioning Adjusting the Flat Panel Friction Tilt Angle Adjusting the Flat Panel to the Original Position Place one hand at the center top edge of the Place one hand at the center top edge of the flat flat panel. Place the other hand on the center bottom edge of the flat panel. Using the upper hand, gently pull the top of the flat panel towards you while the lower hand gently pushes the bottom of the flat panel away from you.
ECM-3763Q Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What Premier Mounts Will Do At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is defective.
